1. DL manuals
  2. Lanpro
  3. Switch
  4. LP-SGW2404FP
  5. Installation Manual

Lanpro LP-SGW2404FP Installation Manual

Manual is about: 24 copper poe + 4 fiver gigabit managed switch

Summary of LP-SGW2404FP

  • Page 1

    Lpsgw2404fp_ig_enb01w lp-sgw2404fp 24 copper poe + 4 fiber gigabit managed switch rev1.0.0

  • Page 2: Fcc Statement

    Fcc statement this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Thi...

  • Page 3: Contents

    Contents package contents ..........................................................................1 chapter 1 introduction.....................................................................2 1.1 intended audience ..................................................................2 1.2 guide overv...

  • Page 4: Package Contents

    1 package contents the following contents should be found in your package: one lp-sgw 2404fp switch one power cord one console cable one ground cable two mounting brackets and other fittings installation guide resource cd for lp-sgw2404fp switch, including: • user guide • cli reference guide • other...

  • Page 5: Chapter 1

    2 chapter 1 introduction thank you for choosing the lp-sgw2404fp. The switch provides a friendly management interface and excellent performance. 1.1 intended audience this guide is intended for network administrators familiar with it concepts and network terminology. 1.2 guide overview this installa...

  • Page 6: Chapter 2

    3 chapter 2 device description 2.1 introduction to the device the lp-sgw 2404fp switch, designed for workgroups and departments, provides wire-speed performance and abundant layer 2 management features. It provides a variety of service features and multiple powerful functions with high security. The...

  • Page 7: 2.3

    4 + gvrp (garp vlan registration protocol) allows automatic learning and dynamic assignment of vlans. Quality of service + supports l2/l3 granular cos with 4 priority queues per port. + rate limiting confines the traffic flow accurately according to the preset value. Security + supports multiple ind...

  • Page 8

    5 storage temperature -40 ℃ ~ 70℃ operating humidity 10% ~ 90% rh non-condensing storage humidity 5% ~ 90% rh non-condensing.

  • Page 9: Chapter 3

    6 chapter 3 mounting device 3.1 precautions to ensure a long-term and stable performance of the switch, please pay attention to the following before the installation. 1) safety requirements • before cleaning the switch, cut off the power supply. Do not clean it by the waterish cloth, and never use a...

  • Page 10

    7 1) set the switch on a flat surface strong enough to support the entire weight of the switch with all fittings. 2) remove the adhesive backing papers from the rubber feet. 3) turnover the switch and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the switch. F...

  • Page 11: 3.3

    8 figure 3-3 mounting switch 3.3 connect to ground connecting the switch to ground is to quickly release the lightning over-voltage and over-current of the switch, which is also a necessary measure to protect the body from electric shock. In different environments, the switch may be grounded differe...

  • Page 12: Chapter 4

    9 chapter 4 switch appearance description 4.1 front panel the front panel of lp-sgw2404fp is configured as follows: figure 4-1 lp-sgw2404fp front panel  leds lp-sgw 2404fp has an led mode switch button which is for switching the led status indication. When the speed led is on, the port led is indic...

  • Page 13

    10 when the poe led is on, the port led is indicating the power supply status. Led status indication power on the switch is powered on. Flashing power supply is abnormal. Off the switch is powered off or power supply is abnormal. System on/off the switch works improperly flashing the switch works pr...

  • Page 14: 4.2

    11 port is 1000mfd. 4.2 back panel the back panel of the switch is configured as follows: figure 4-2 lp-sgw2404fp back panel  grounding terminal: the switch already comes with lightning protection mechanism. You can also ground the switch through the pe (protecting earth) cable of ac cord or with g...

  • Page 15: Chapter 5

    12 chapter 5 configuration 5.1 configure the switch via gui 1. Connect the ethernet ports of the switch to the pc. 2. To access the gui of the switch, open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the enter key. Figure 5...

  • Page 16: 5.2

    13 figure 5-3 main page of the switch 5.2 configure the switch via cli you can log on to the switch and access the cli by the following two methods: 1. Log on to the switch by the console port on the switch. 2. Log on to the switch remotely by a telnet or ssh connection through an ethernet port. 5.2...

  • Page 17

    14 “lp-sgw 2404fp>” will appear after pressing the enter button. It indicates that you can use the cli now. 5.2.2 logon by telnet to log on to the switch by a telnet connection, please take the following steps: 1. Firstly cli commands about configuring telnet login mode, login authentication informa...

  • Page 18

    15 appendix a: troubleshooting q1. What could i do if i forgot the username and password of the switch? 1. Connect the console port of the pc to the console port of the switch and open hyper terminal. 2. Power off and restart the switch. When you are prompted that “press ctrl-b to enter the bootutil...

  • Page 19

    16 3. Turn off the power. After a while, turn on the power again. 4. Make sure the ip address of your pc is set within the subnet of the switch. 5. If you still cannot access the configuration page, please restore the switch to its factory defaults. Then the ip address should be set as 192.168.0.X (...