- DL manuals
- Lantronix
- Server
- MatchPort b/g Pro
- Command Reference Manual
Lantronix MatchPort b/g Pro Command Reference Manual
Summary of MatchPort b/g Pro
Page 1
Part number 900-534 revision d may 2013 matchport b/g pro embedded device server command reference.
Page 2
Matchport® b/g pro embedded device server command reference 2 copyright and trademark © 2013 lantronix, inc. All rights reserved. No part of the contents of this book may be transmitted or reproduced in any form or by any means without the written permission of lantronix. Matchport® and lantronix® a...
Page 3
Matchport® b/g pro embedded device server command reference 3 table of contents list of figures _____________________________________________________________ 4 list of tables ______________________________________________________________ 5 1: about this guide 6 chapter summaries ____________________...
Page 4
Matchport® b/g pro embedded device server command reference 4 list of figures figure 3-1 cli level hierarchy ______________________________________________________ 12 figure 3-2 login level commands ___________________________________________________ 13 figure 3-3 enable level commands______________...
Page 5
Matchport® b/g pro embedded device server command reference 5 list of tables table 4-8 xcr groups ____________________________________________________________ 20 table 4-9 xsr groups and items ____________________________________________________ 33 table 5-1 commands and levels _____________________...
Page 6: About This Guide
Matchport® b/g pro embedded device server command reference 6 1: about this guide this guide describes how to configure the matchport® b/g pro embedded device server using the command line interface (cli) and/or extensible markup language (xml). Cli provides an interactive mode for accessing the dev...
Page 7
1: about this guide matchport® b/g pro embedded device server command reference 7 additional documentation visit the lantronix web site at www.Lantronix.Com/support/documentation for the latest documentation and the following additional documentation. Caution caution: means you might do something th...
Page 8: Overview
Matchport® b/g pro embedded device server command reference 8 2: overview evolution os® software is the lantronix® cutting-edge operating system that supports three convenient configuration methods: web manager, command line interface (cli), and extensible markup language (xml). For more information...
Page 9: Command Line Interface
Matchport® b/g pro embedded device server command reference 9 3: command line interface this chapter describes accessing the matchport® b/g pro embedded device server by using telnet, ssh, or serial ports to configure the matchport, navigating the command line interface (cli), typing keyboard shortc...
Page 10
3: command line interface matchport® b/g pro embedded device server command reference 10 to configure the lantronix device server locally using a serial port, connect a terminal or a pc running a terminal emulation program to one of the device server's serial ports. Configure the terminal for 9600 b...
Page 11
3: command line interface matchport® b/g pro embedded device server command reference 11 using keyboard shortcuts and cli one useful shortcut built into evolution os operating system is that the complete text of a command does not have to be entered to issue a command. Typing just enough characters ...
Page 12
3: command line interface matchport® b/g pro embedded device server command reference 12 figure 3-1 cli level hierarchy (login) enable ssl cli http arp ethernet link if 1 ip ip filter query port rss snmp syslog tcp tftp udp terminal network ftp serial packing modem disconnect connect accept tunnel s...
Page 13
3: command line interface matchport® b/g pro embedded device server command reference 13 commands at the login level, shown in figure 3-2 , do not affect current configuration settings and are not displayed initially. If you type ?>, you will see the login sub-commands. These commands provide diagno...
Page 14: Configuration Using Xml
Matchport® b/g pro embedded device server command reference 14 4: configuration using xml the matchport® b/g pro embedded device server provides an extensible markup language (xml) interface that you can use to configure device server devices. Every configuration setting that can be issued from the ...
Page 15
4: configuration using xml matchport® b/g pro embedded device server command reference 15 notes: the name for each (specified with the name attribute) is the group name listed in the web manager xcr groups or with the “xcr list” cli command. See the matchport b/g pro user guide for more information ...
Page 16
4: configuration using xml matchport® b/g pro embedded device server command reference 16 record, group, item, and value tags a is a logical grouping of configuration parameters and must contain one or more elements. It must have a name attribute and may have an instance attribute. A is a specific g...
Page 17
4: configuration using xml matchport® b/g pro embedded device server command reference 17 figure 4-5 xml example of multiple items figure 4-6 xml example with multiple groups importing and exporting an xml configuration file an xcr can be imported or exported using the following methods: filesystem—...
Page 18
4: configuration using xml matchport® b/g pro embedded device server command reference 18 settings specified. This can be done on any level, including the root. Special tags in the xml allow for providing root and enable level passwords so that this can also be done at the password prompt. Web brows...
Page 19
4: configuration using xml matchport® b/g pro embedded device server command reference 19 the following syntax can be used to export configurations to a file on the device server’s file system: xcr export file> xcr export file> groups and/or group:instances> the same guidelines above regarding impor...
Page 20
4: configuration using xml matchport® b/g pro embedded device server command reference 20 the “xml paste passwords” name is used with the “passwords” name and “cli login” and “cli enable level” values to specify the passwords to use when the device has been configured with password protection. The p...
Page 21
4: configuration using xml matchport® b/g pro embedded device server command reference 21 cli (continued) quit connect line accepts text containing control characters, for example, a represents control-a default: l inactivity timeout , ... Default: 15 minutes cp group (attribute of “instance” is req...
Page 22
4: configuration using xml matchport® b/g pro embedded device server command reference 22 email (attribute of “instance” is a number.) (continued) priority urgent, high, normal, low, very low default: normal cp group trigger value ethernet (attribute of “instance” is “eth0”.) speed auto, 10, 100 def...
Page 23
4: configuration using xml matchport® b/g pro embedded device server command reference 23 http server (continued) log format default: %h %t "%r" %s %b "%{referer}i" "%{user-agent}i" authentication timeout default: 30 minutes icmp state enable, disable default: enable interface (attribute of “instanc...
Page 24
4: configuration using xml matchport® b/g pro embedded device server command reference 24 ip filter delete entries enable, disable if enabled, deletes any existing entries before adding “filter entry”. Filter delete ip address deletes a specific ip filter entry. Net mask deletes a specific ip filter...
Page 25
4: configuration using xml matchport® b/g pro embedded device server command reference 25 modbus tcp server state enable, disable default: disable additional port , ... Default: response timeout default: 3000 milliseconds rss trace input enable, disable default: disable power management state enable...
Page 26
4: configuration using xml matchport® b/g pro embedded device server command reference 26 snmp state enable, disable default: enable read community value is secret, hidden from user view. Default: public write community value is secret, hidden from user view. Default: private system contact system n...
Page 27
4: configuration using xml matchport® b/g pro embedded device server command reference 27 ssh server host rsa keys public key private key host dsa keys public key private key delete authorized users authorized user delete name authorized user (attribute of “instance” is required for the authorized u...
Page 28
4: configuration using xml matchport® b/g pro embedded device server command reference 28 tcp (continued) max retrans max retrans syn ack send data telnet state enable, disable default: enable port default: 23 max sessions default: 3 terminal (attribute of “instance” is either “network” or a number....
Page 29
4: configuration using xml matchport® b/g pro embedded device server command reference 29 tunnel accept (attribute of “instance” is a number.) (continued) block serial enable, disable default: disable block network enable, disable default: disable password password value is secret, hidden from user ...
Page 30
4: configuration using xml matchport® b/g pro embedded device server command reference 30 tunnel connect (attribute of “instance” is a number.) (continued) email connect , ... Default: email disconnect , ... Default: cp output goup connection value, disconnection value tunnel disconnect (attribute o...
Page 31
4: configuration using xml matchport® b/g pro embedded device server command reference 31 tunnel serial (attribute of “instance” is a number.) dtr asserted while connected, continuously asserted, unasserted, truport default: asserted while connected vip state enable, disable default: disable wlan ch...
Page 32
4: configuration using xml matchport® b/g pro embedded device server command reference 32 wlan profile(attribute of an “instance” is “default_ adhoc_profile” or “default_infrastru cture_profile”) (continued) security suite key type passphrase wep authentication wep key size wep tx key index wep key ...
Page 33
4: configuration using xml matchport® b/g pro embedded device server command reference 33 xml status record groups and items table 4-9 lists the supported xml status record (xsr) groups and items. These groups and items show the status of the device in xml form and can only be exported. The xsr sche...
Page 34
4: configuration using xml matchport® b/g pro embedded device server command reference 34 ethernet driver (within group “buffer pool”.) buffer headers total free used max used cluster pool cluster size total free used max used filesystem filesystem size available space clean space dirty space file a...
Page 35
4: configuration using xml matchport® b/g pro embedded device server command reference 35 ftp status running inactive connections rejected accepted last client ip address port hardware cpu type speed memory flash size ram size http state enabled disabled logging entries bytes http log entry (attribu...
Page 36
4: configuration using xml matchport® b/g pro embedded device server command reference 36 icmp in messages messages discarded errors destination unreachable time exceeded messages parameter problems source quench requests redirects ping requests ping replies timestamp requests timestamp replies addr...
Page 37
4: configuration using xml matchport® b/g pro embedded device server command reference 37 interface (attribute of “instance” is “eth0”.) generic status no link link up disabled unknown errors (error text) none ethernet (present only for eth0.) speed 10 100 duplex full half arp encapsulation arpa typ...
Page 38
4: configuration using xml matchport® b/g pro embedded device server command reference 38 interface (attribute of “instance” is “eth0”.) (continued.) transmit octets unicast non unicast discards errors broadcast packets multicast packets filtered packets deferred multiple retries one retry underflow...
Page 39
4: configuration using xml matchport® b/g pro embedded device server command reference 39 interface (attribute of an “instance” is “wlan0”) (continued) in receives header errors address errors unknown protocols discarded delivered out requests discards discards no route reassembly timeout needed suc...
Page 40
4: configuration using xml matchport® b/g pro embedded device server command reference 40 line (attribute of “instance” is a number.) receiver bytes breaks parity errors framing errors overrun errors no receive buffer errors queued bytes flow control n/a stop go transmitter bytes breaks queued bytes...
Page 41
4: configuration using xml matchport® b/g pro embedded device server command reference 41 line (with no instance.) (within group “line” with instance.) (continued) flow control hardware none software xon char xoff char memory main heap condition clean corrupt total memory available memory fragments ...
Page 42
4: configuration using xml matchport® b/g pro embedded device server command reference 42 ssh state active waiting disabled totals uptime bytes in bytes out tcp retransmission algorithm vanj timeout minimum timeout maximum connections maximum open active open passive failed resets established errors...
Page 43
4: configuration using xml matchport® b/g pro embedded device server command reference 43 tunnel (attribute of “instance” is a number.) aggregate completed connects completed accepts disconnects dropped connects dropped accepts octets from serial octets from network connect connection time accept co...
Page 44: 5: Commands And Levels
Matchport® b/g pro embedded device server command reference 44 5: commands and levels click the level in the tree structure and it will take you to the command list for that level. Root • enable (enable) • configure (config) • arp (config-arp) • bridge 1 (config-bridge:bridge0) • cli (config-cli) • ...
Page 45
5: commands and levels matchport® b/g pro embedded device server command reference 45 • snmp (config-snmp) • traps (config-snmp-traps) • syslog (config-syslog) • tcp (config-tcp) • terminal 1 (config-terminal:1) • terminal 2 (config-terminal:2) • terminal network (config-terminal:network) • tftp (co...
Page 46
5: commands and levels matchport® b/g pro embedded device server command reference 46 • dns (dns) • email 1 (email:1) • cp (email-cp:1) • email 2 (email:2) • cp (email-cp:2) • email 3 (email:3) • cp (email-cp:3) • email 4 (email:4) • cp (email-cp:4) • filesystem (filesystem) • line 1 (line:1) • line...
Page 47
5: commands and levels matchport® b/g pro embedded device server command reference 47 • host 3 (tunnel-connect-host:2:3) • host 4 (tunnel-connect-host:2:4) • host 5 (tunnel-connect-host:2:5) • host 6 (tunnel-connect-host:2:6) • host 7 (tunnel-connect-host:2:7) • host 8 (tunnel-connect-host:2:8) • ho...
Page 48
5: commands and levels matchport® b/g pro embedded device server command reference 48 bytes may run together or be separated by optional punc- tuation: 123abc "12 3a bc" 12,3a,bc 12.3a.Bc 12:3a:bc note that quotes must enclose the value if it contains spaces. Aes encrypt key text sets the accept tun...
Page 49
5: commands and levels matchport® b/g pro embedded device server command reference 49 no local port uses the default port number as the local port for accept mode tunneling. The default port is 10000 + #, where # is the line number for this tunnel. No tcp keep alive disables the accept mode tcp keep...
Page 50
5: commands and levels matchport® b/g pro embedded device server command reference 50 aes encrypt key sets the accept tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123abc "12 3a bc" 1...
Page 51
5: commands and levels matchport® b/g pro embedded device server command reference 51 accept mode tunnel. No email disconnect discontinues sending email alerts upon closing an accept mode tunnel. No local port uses the default port number as the local port for accept mode tunneling. The default port...
Page 52
5: commands and levels matchport® b/g pro embedded device server command reference 52 beacon is 100 msec.) security switch to security level show displays the current configuration. Show history displays the last 20 commands entered during the current cli session. Tx data rate auto-reduction enables...
Page 53
5: commands and levels matchport® b/g pro embedded device server command reference 53 show displays the current configuration. Show history displays the last 20 commands entered during the current cli session. Tx data rate auto-reduction enables tx data rate auto-reduction. Tx data rate fixed enable...
Page 54
5: commands and levels matchport® b/g pro embedded device server command reference 54 exit exits to the config level. No bridging mac address removes the bridging mac address. Show displays the current configuration. Show history displays the last 20 commands entered during the current cli session. ...
Page 55
5: commands and levels matchport® b/g pro embedded device server command reference 55 if the settings do not work, when you reboot the device, it will still have the original settings. Clrscrn clears the screen. Exit exits to the next higher level. No profile removes reference to the profile. Profil...
Page 56
5: commands and levels matchport® b/g pro embedded device server command reference 56 show user show information for a user user set username and rsa or dsa keys user command customizes the user command user generate dsa 1024 generate dsa public and private keys user generate dsa 512 generate dsa pu...
Page 57
5: commands and levels matchport® b/g pro embedded device server command reference 57 = number of the terminal line (serial port) to be con- figured. Terminal network enters the configure-terminal level for the network. Tftp enters the tftp level. Udp changes to the command level for udp configurati...
Page 58
5: commands and levels matchport® b/g pro embedded device server command reference 58 flush serial disable characters already in the serial data buffer are retained upon establishing a connect mode tunneling connection. Flush serial enable flushes the serial data buffer upon establishing a connect m...
Page 59
5: commands and levels matchport® b/g pro embedded device server command reference 59 connections. Connect mode any character enables the tunneling server to establish a tunneling con- nection when a character is received on the corresponding line (serial port). Connect mode disable disables connect...
Page 60
5: commands and levels matchport® b/g pro embedded device server command reference 60 no email disconnect discontinues sending email alerts upon closing a connect mode tunnel. Promote host promotes the identified host, exchanging it place with the host above it, to adjust the order of the defined ho...
Page 61
5: commands and levels matchport® b/g pro embedded device server command reference 61 group specify a cp group that shall trigger an email. = configurable pin group. No group disables the trigger to send an email. No trigger value clears the value that shall trigger an email. Show shows the current ...
Page 62
5: commands and levels matchport® b/g pro embedded device server command reference 62 = binary to output (typically 1 or 0). Default connection value restores the default value for accept mode connection. Default disconnection value restores the default value for accept mode disconnection. Disconnec...
Page 63
5: commands and levels matchport® b/g pro embedded device server command reference 63 show shows the current configuration. Show history displays the last 20 commands entered during the current cli session. Write stores the current configuration in permanent memory. Cpm (cpm) level commands add to a...
Page 64
5: commands and levels matchport® b/g pro embedded device server command reference 64 auto show tlog continuously displays the internal trouble log. Auto show upload continuously displays the status of firmware upload. Clrscrn clears the screen. Default long name restores the default product long na...
Page 65
5: commands and levels matchport® b/g pro embedded device server command reference 65 asserted. No stop character removes the stop character. No timeout disables disconnect after timeout feature for tunneling sessions. Show displays the current configuration. Show history displays the last 20 comman...
Page 66
5: commands and levels matchport® b/g pro embedded device server command reference 66 remove host removes an entry from the dns cache. Show show dns status and cache entries. Show history displays the last 20 commands entered during the current cli session. Write stores the current configuration in ...
Page 67
5: commands and levels matchport® b/g pro embedded device server command reference 67 clear log clears all entries from the mail log. Clear mail counters sets the email counters to zero. Clrscrn clears the screen. Cp enters the next lower level. Default local port sets the local port (used to send e...
Page 68
5: commands and levels matchport® b/g pro embedded device server command reference 68 to sets to addresses for email alerts. = a quoted, semicolon separated list of email ad- dresses. Write stores the current configuration in permanent memory. Email 2 (email:2) level commands auto show statistics co...
Page 69
5: commands and levels matchport® b/g pro embedded device server command reference 69 server port sets the port used by the smtp server. = port used for smtp on the server side. Show displays the current configuration. Show history displays the last 20 commands entered during the current cli session...
Page 70
5: commands and levels matchport® b/g pro embedded device server command reference 70 priority high sets x-priority for email alerts to 2 (high). Priority low sets x-priority for email alerts to 4 (low). Priority normal sets x-priority for email alerts to 3 (normal). Priority urgent sets x-priority ...
Page 71
5: commands and levels matchport® b/g pro embedded device server command reference 71 no reply to removes the reply to address for email alerts. No subject removes subject used for email alerts. No to removes the to addresses for email alerts. Overriding domain sets a domain name that will be used w...
Page 72
5: commands and levels matchport® b/g pro embedded device server command reference 72 no clear interfaces counters unzeros interface session counters ping ping destination continuously with 5 second timeout ping ping destination n times with 5 second timeout ping ping destination n times with x time...
Page 73
5: commands and levels matchport® b/g pro embedded device server command reference 73 rmdir remove a directory show show file system statistics show history displays the last 20 commands entered during the current cli session. Show tree show all files and directories from current directory tftp get ...
Page 74
5: commands and levels matchport® b/g pro embedded device server command reference 74 aes encrypt key sets the connect tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123abc "12 3a bc" ...
Page 75
5: commands and levels matchport® b/g pro embedded device server command reference 75 validate certificate enable requires verification of the server certificate when con- necting. Vip disable makes connections using the specified address. Vip enable makes connections using the vip name. Vip name se...
Page 76
5: commands and levels matchport® b/g pro embedded device server command reference 76 protocol ssl uses ssl protocol for connect mode tunneling. Protocol tcp uses tcp protocol for connect mode tunneling. Protocol tcp aes uses tcp protocol with aes encryption for connect mode tunneling. Protocol teln...
Page 77
5: commands and levels matchport® b/g pro embedded device server command reference 77 ssh username sets the username for logging into the host via ssh. = username. Write stores the current configuration in permanent memory. Host 10 (tunnel-connect-host:2:10) level commands address sets the remote ho...
Page 78
5: commands and levels matchport® b/g pro embedded device server command reference 78 protocol telnet uses telnet protocol (with iac) for connect mode tunnel- ing. Protocol udp uses udp protocol for connect mode tunneling. Protocol udp aes uses udp protocol with aes encryption for connect mode tunne...
Page 79
5: commands and levels matchport® b/g pro embedded device server command reference 79 clrscrn clears the screen. Default protocol restores the default protocol as "tcp". Default tcp keep alive restores the default 45 second connect mode tcp keep alive timeout. Exit exits to the next higher level. No...
Page 80
5: commands and levels matchport® b/g pro embedded device server command reference 80 host change to config host level name sets the name of the host. = name of the host. No name clears the name of the host. No remote address clears the remote address of the host. No ssh username clears the ssh user...
Page 81
5: commands and levels matchport® b/g pro embedded device server command reference 81 exit exits to the next higher level. No address removes the remote host address used to establish tun- neling connections. No aes decrypt key removes the connect tunnel aes decrypt key. No aes encrypt key removes t...
Page 82
5: commands and levels matchport® b/g pro embedded device server command reference 82 aes decrypt key text sets the connect tunnel aes decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. Aes encrypt key sets ...
Page 83
5: commands and levels matchport® b/g pro embedded device server command reference 83 sets the timer. = timer value, in milliseconds. Validate certificate disable skips verification of the server certificate when connect- ing. Validate certificate enable requires verification of the server certifica...
Page 84
5: commands and levels matchport® b/g pro embedded device server command reference 84 spaces. Aes encrypt key sets the connect tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run together or be separated by optional punc- tuation: 123abc "12...
Page 85
5: commands and levels matchport® b/g pro embedded device server command reference 85 ing. Validate certificate enable requires verification of the server certificate when con- necting. Vip disable makes connections using the specified address. Vip enable makes connections using the vip name. Vip na...
Page 86
5: commands and levels matchport® b/g pro embedded device server command reference 86 protocol ssh uses ssh protocol for connect mode tunneling. Protocol ssl uses ssl protocol for connect mode tunneling. Protocol tcp uses tcp protocol for connect mode tunneling. Protocol tcp aes uses tcp protocol wi...
Page 87
5: commands and levels matchport® b/g pro embedded device server command reference 87 cli session. Ssh username sets the username for logging into the host via ssh. = username. Write stores the current configuration in permanent memory. Host 13 (tunnel-connect-host:2:13) level commands address sets ...
Page 88
5: commands and levels matchport® b/g pro embedded device server command reference 88 protocol tcp aes uses tcp protocol with aes encryption for connect mode tunneling. Protocol telnet uses telnet protocol (with iac) for connect mode tunnel- ing. Protocol udp uses udp protocol for connect mode tunne...
Page 89
5: commands and levels matchport® b/g pro embedded device server command reference 89 auto show statistics show connection statistics clrscrn clears the screen. Default protocol restores the default protocol as "tcp". Default tcp keep alive restores the default 45 second connect mode tcp keep alive ...
Page 90
5: commands and levels matchport® b/g pro embedded device server command reference 90 exit exits to the configuration level. Host change to config host level name sets the name of the host. = name of the host. No name clears the name of the host. No remote address clears the remote address of the ho...
Page 91
5: commands and levels matchport® b/g pro embedded device server command reference 91 alive timeout. Exit exits to the next higher level. No address removes the remote host address used to establish tun- neling connections. No aes decrypt key removes the connect tunnel aes decrypt key. No aes encryp...
Page 92
5: commands and levels matchport® b/g pro embedded device server command reference 92 spaces. Aes decrypt key text sets the connect tunnel aes decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. Aes encrypt k...
Page 93
5: commands and levels matchport® b/g pro embedded device server command reference 93 tcp keep alive enables tcp keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. Validate certificate disable skips verification of the server certificate when connect- ing. Vali...
Page 94
5: commands and levels matchport® b/g pro embedded device server command reference 94 note that quotes must enclose the value if it contains spaces. Aes encrypt key sets the connect tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run togethe...
Page 95
5: commands and levels matchport® b/g pro embedded device server command reference 95 validate certificate disable skips verification of the server certificate when connect- ing. Validate certificate enable requires verification of the server certificate when con- necting. Vip disable makes connecti...
Page 96
5: commands and levels matchport® b/g pro embedded device server command reference 96 protocol ssh uses ssh protocol for connect mode tunneling. Protocol ssl uses ssl protocol for connect mode tunneling. Protocol tcp uses tcp protocol for connect mode tunneling. Protocol tcp aes uses tcp protocol wi...
Page 97
5: commands and levels matchport® b/g pro embedded device server command reference 97 cli session. Ssh username sets the username for logging into the host via ssh. = username. Write stores the current configuration in permanent memory. Host 16 (tunnel-connect-host:2:16) level commands address sets ...
Page 98
5: commands and levels matchport® b/g pro embedded device server command reference 98 protocol tcp aes uses tcp protocol with aes encryption for connect mode tunneling. Protocol telnet uses telnet protocol (with iac) for connect mode tunnel- ing. Protocol udp uses udp protocol for connect mode tunne...
Page 99
5: commands and levels matchport® b/g pro embedded device server command reference 99 auto show statistics show connection statistics clrscrn clears the screen. Default protocol restores the default protocol as "tcp". Default tcp keep alive restores the default 45 second connect mode tcp keep alive ...
Page 100
5: commands and levels matchport® b/g pro embedded device server command reference 100 exit exits to the configuration level. Host change to config host level name sets the name of the host. = name of the host. No name clears the name of the host. No remote address clears the remote address of the h...
Page 101
5: commands and levels matchport® b/g pro embedded device server command reference 101 alive timeout. Exit exits to the next higher level. No address removes the remote host address used to establish tun- neling connections. No aes decrypt key removes the connect tunnel aes decrypt key. No aes encry...
Page 102
5: commands and levels matchport® b/g pro embedded device server command reference 102 spaces. Aes decrypt key text sets the connect tunnel aes decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. Aes encrypt ...
Page 103
5: commands and levels matchport® b/g pro embedded device server command reference 103 tcp keep alive enables tcp keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. Validate certificate disable skips verification of the server certificate when connect- ing. Val...
Page 104
5: commands and levels matchport® b/g pro embedded device server command reference 104 note that quotes must enclose the value if it contains spaces. Aes encrypt key sets the connect tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run togeth...
Page 105
5: commands and levels matchport® b/g pro embedded device server command reference 105 validate certificate disable skips verification of the server certificate when connect- ing. Validate certificate enable requires verification of the server certificate when con- necting. Vip disable makes connect...
Page 106
5: commands and levels matchport® b/g pro embedded device server command reference 106 protocol ssh uses ssh protocol for connect mode tunneling. Protocol ssl uses ssl protocol for connect mode tunneling. Protocol tcp uses tcp protocol for connect mode tunneling. Protocol tcp aes uses tcp protocol w...
Page 107
5: commands and levels matchport® b/g pro embedded device server command reference 107 cli session. Ssh username sets the username for logging into the host via ssh. = username. Write stores the current configuration in permanent memory. Host 4 (tunnel-connect-host:2:4) level commands address sets t...
Page 108
5: commands and levels matchport® b/g pro embedded device server command reference 108 protocol tcp aes uses tcp protocol with aes encryption for connect mode tunneling. Protocol telnet uses telnet protocol (with iac) for connect mode tunnel- ing. Protocol udp uses udp protocol for connect mode tunn...
Page 109
5: commands and levels matchport® b/g pro embedded device server command reference 109 auto show statistics show connection statistics clrscrn clears the screen. Default protocol restores the default protocol as "tcp". Default tcp keep alive restores the default 45 second connect mode tcp keep alive...
Page 110
5: commands and levels matchport® b/g pro embedded device server command reference 110 exit exits to the configuration level. Host change to config host level name sets the name of the host. = name of the host. No name clears the name of the host. No remote address clears the remote address of the h...
Page 111
5: commands and levels matchport® b/g pro embedded device server command reference 111 alive timeout. Exit exits to the next higher level. No address removes the remote host address used to establish tun- neling connections. No aes decrypt key removes the connect tunnel aes decrypt key. No aes encry...
Page 112
5: commands and levels matchport® b/g pro embedded device server command reference 112 spaces. Aes decrypt key text sets the connect tunnel aes decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. Aes encrypt ...
Page 113
5: commands and levels matchport® b/g pro embedded device server command reference 113 tcp keep alive enables tcp keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. Validate certificate disable skips verification of the server certificate when connect- ing. Val...
Page 114
5: commands and levels matchport® b/g pro embedded device server command reference 114 note that quotes must enclose the value if it contains spaces. Aes encrypt key sets the connect tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run togeth...
Page 115
5: commands and levels matchport® b/g pro embedded device server command reference 115 validate certificate disable skips verification of the server certificate when connect- ing. Validate certificate enable requires verification of the server certificate when con- necting. Vip disable makes connect...
Page 116
5: commands and levels matchport® b/g pro embedded device server command reference 116 protocol ssh uses ssh protocol for connect mode tunneling. Protocol ssl uses ssl protocol for connect mode tunneling. Protocol tcp uses tcp protocol for connect mode tunneling. Protocol tcp aes uses tcp protocol w...
Page 117
5: commands and levels matchport® b/g pro embedded device server command reference 117 cli session. Ssh username sets the username for logging into the host via ssh. = username. Write stores the current configuration in permanent memory. Host 7 (tunnel-connect-host:2:7) level commands address sets t...
Page 118
5: commands and levels matchport® b/g pro embedded device server command reference 118 protocol tcp aes uses tcp protocol with aes encryption for connect mode tunneling. Protocol telnet uses telnet protocol (with iac) for connect mode tunnel- ing. Protocol udp uses udp protocol for connect mode tunn...
Page 119
5: commands and levels matchport® b/g pro embedded device server command reference 119 auto show statistics show connection statistics clrscrn clears the screen. Default protocol restores the default protocol as "tcp". Default tcp keep alive restores the default 45 second connect mode tcp keep alive...
Page 120
5: commands and levels matchport® b/g pro embedded device server command reference 120 exit exits to the configuration level. Host change to config host level name sets the name of the host. = name of the host. No name clears the name of the host. No remote address clears the remote address of the h...
Page 121
5: commands and levels matchport® b/g pro embedded device server command reference 121 alive timeout. Exit exits to the next higher level. No address removes the remote host address used to establish tun- neling connections. No aes decrypt key removes the connect tunnel aes decrypt key. No aes encry...
Page 122
5: commands and levels matchport® b/g pro embedded device server command reference 122 spaces. Aes decrypt key text sets the connect tunnel aes decrypt key with up to 16 bytes. Each byte is represented by a single character. Note that quotes must enclose the value if it contains spaces. Aes encrypt ...
Page 123
5: commands and levels matchport® b/g pro embedded device server command reference 123 tcp keep alive enables tcp keep alive for connect mode tunneling and sets the timer. = timer value, in milliseconds. Validate certificate disable skips verification of the server certificate when connect- ing. Val...
Page 124
5: commands and levels matchport® b/g pro embedded device server command reference 124 note that quotes must enclose the value if it contains spaces. Aes encrypt key sets the connect tunnel aes encrypt key with up to 16 bytes. Each byte is represented by two adjacent hex digits. Bytes may run togeth...
Page 125
5: commands and levels matchport® b/g pro embedded device server command reference 125 validate certificate disable skips verification of the server certificate when connect- ing. Validate certificate enable requires verification of the server certificate when con- necting. Vip disable makes connect...
Page 126
5: commands and levels matchport® b/g pro embedded device server command reference 126 protocol ssh uses ssh protocol for connect mode tunneling. Protocol ssl uses ssl protocol for connect mode tunneling. Protocol tcp uses tcp protocol for connect mode tunneling. Protocol tcp aes uses tcp protocol w...
Page 127
5: commands and levels matchport® b/g pro embedded device server command reference 127 cli session. Ssh username sets the username for logging into the host via ssh. = username. Write stores the current configuration in permanent memory. Http (config-http) level commands auth creates a new http serv...
Page 128
5: commands and levels matchport® b/g pro embedded device server command reference 128 delete auth user deletes an existing user for an http server authentica- tion directive. = uri of the server. = username. Exit returns to the config level. Log format sets the log format string for the http server...
Page 129
5: commands and levels matchport® b/g pro embedded device server command reference 129 write stores the current configuration in permanent memory. Icmp (config-icmp) level commands auto show statistics continuously shows icmp statistics clear counters zeros counters clrscrn clears the screen. Exit e...
Page 130
5: commands and levels matchport® b/g pro embedded device server command reference 130 show displays the current configuration. Show history displays the last 20 commands entered during the current cli session. Show status show interface status state disable disables the interface. State enable enab...
Page 131
5: commands and levels matchport® b/g pro embedded device server command reference 131 ip (config-ip) level commands auto show statistics continuously shows ip statistics clear counters zeros counters clrscrn clears the screen. Default ip time to live restores the default ip time to live. Default mu...
Page 132
5: commands and levels matchport® b/g pro embedded device server command reference 132 write stores the current configuration in permanent memory. Key 1 (config-profile-security-wep-key:default_adhoc_profile:1) level commands apply wlan try out wlan settings without saving them to flash. If the sett...
Page 133
5: commands and levels matchport® b/g pro embedded device server command reference 133 tuation: 123abc "12 3a bc" 12,3a,bc 12.3a.Bc 12:3a:bc note that quotes must enclose the value if it contains spaces. Key text sets key. Each byte is represented by a single character. Note that quotes must enclose...
Page 134
5: commands and levels matchport® b/g pro embedded device server command reference 134 cli session. Write stores the current configuration in permanent memory. Key 4 (config-profile-security-wep-key:default_infrastructure_profile:4) level commands apply wlan try out wlan settings without saving them...
Page 135
5: commands and levels matchport® b/g pro embedded device server command reference 135 command mode always sets the current line to always be in command mode. Command mode cp sets the current line to enter command mode under con- trol of a cp. Command mode cp specifies the cp group and trigger value...
Page 136
5: commands and levels matchport® b/g pro embedded device server command reference 136 kill session kills command mode session on the line line enters the line level. = number of the line (serial port) to be configured. Lpd enters the configure lpd level. = number of the line (lpd serial port) to be...
Page 137
5: commands and levels matchport® b/g pro embedded device server command reference 137 write stores the current configuration in permanent memory. Xoff char sets the xoff character for use with software flow control on this line. The character may be input as text, control, decimal, or hex. A contro...
Page 138
5: commands and levels matchport® b/g pro embedded device server command reference 138 default data bits restores the default of eight data bits. Default flow control restores the default of no flow control. Default interface restores the default interface type to this line. Default parity restores ...
Page 139
5: commands and levels matchport® b/g pro embedded device server command reference 139 reassert asserts line status with current configured values. Show displays the current status. Show command mode shows the command mode settings for the current line. Show history displays the last 20 commands ent...
Page 140
5: commands and levels matchport® b/g pro embedded device server command reference 140 roaming disable disables roaming. Roaming enable enables roaming to other access points with the same ssid. Scan scan the radio environment for all networks. Scan scan the radio environment for the named network. ...
Page 141
5: commands and levels matchport® b/g pro embedded device server command reference 141 clrscrn clears the screen. Exit exits to the enable level. Kill kills the current print job on the specified line. = lpd line with print job. Show displays lpd status for the specified line. = lpd line to display....
Page 142
5: commands and levels matchport® b/g pro embedded device server command reference 142 no queue name removes the queue name. No soj text removes the start-of-job string. Ppp enters the serial line ppp level. Queue name sets the name of the queue that this lpd line belongs to. = name for the queue. S...
Page 143
5: commands and levels matchport® b/g pro embedded device server command reference 143 eoj text binary sets the end-of-job text allowing for binary characters. = string in binary format that will be sent to the printer at the end of each print job. Within [] use binary decimal up to 255 or hex up to...
Page 144
5: commands and levels matchport® b/g pro embedded device server command reference 144 additional port sets an additional tcp server port. Clrscrn clears the screen. Default response timeout restores the default modbus response timeout. Exit exits to the config level. Kill connection kills modbus co...
Page 145
5: commands and levels matchport® b/g pro embedded device server command reference 145 verbose response enable sends modem response codes out on the serial line. Write stores the current configuration in permanent memory. Modem (tunnel-modem:1) level commands clrscrn clears the screen. Connect strin...
Page 146
5: commands and levels matchport® b/g pro embedded device server command reference 146 packing mode timeout sets packing mode to accumulate data and transmit it after a specified amount of time (timeout). Send character sets the send character for packing mode. The character may be input as text, co...
Page 147
5: commands and levels matchport® b/g pro embedded device server command reference 147 = timeout value, in milliseconds. Trailing character sets the trailing character for packing mode. The character may be input as text, control, decimal, or hex. A control character has the form c. A decimal value ...
Page 148
5: commands and levels matchport® b/g pro embedded device server command reference 148 exit exits to the configuration level. Line enters the line level. = number of the line (serial port) to be configured. Local ip sets the local ip address and network mask. Formats accepted: 192.168.1.1 (default m...
Page 149
5: commands and levels matchport® b/g pro embedded device server command reference 149 no local ip removes the local ip address. No password removes the ppp authentication password. No peer ip removes the peer ip address. No username removes the ppp authentication username. Password sets the passwor...
Page 150
5: commands and levels matchport® b/g pro embedded device server command reference 150 feed enable enables rss feed. Max entries sets the maximum number of rss feed entries. Persist disable disables rss feed data persistence. Persist enable enables rss feed data persistence. Show displays the curren...
Page 151
5: commands and levels matchport® b/g pro embedded device server command reference 151 wpax enters the next lower level. Write stores the current configuration in permanent memory. Security (config-profile-security:default_adhoc_profile) level commands advanced switch to advanced level apply wlan tr...
Page 152
5: commands and levels matchport® b/g pro embedded device server command reference 152 clrscrn clears the screen. Default dtr restores default dtr control, asserted while connected. Dtr asserted while connected asserts dtr whenever a connect or accept mode tunnel connection is active. Dtr continuous...
Page 153
5: commands and levels matchport® b/g pro embedded device server command reference 153 snmp (config-snmp) level commands clrscrn clears the screen. Default read community clears the snmp read-only community. Default system description restores the snmp system description to its default. Default syst...
Page 154
5: commands and levels matchport® b/g pro embedded device server command reference 154 show history displays the last 20 commands entered during the current cli session. Show statistics displays the ssh server statistics. State disable disables the ssh server. State enable enables the ssh server. Wr...
Page 155
5: commands and levels matchport® b/g pro embedded device server command reference 155 show history displays the last 20 commands entered during the current cli session. Show statistics displays the syslog statistics. State disable disables syslog logging. State enable enables syslog logging. Write ...
Page 156
5: commands and levels matchport® b/g pro embedded device server command reference 156 = local port number. Show displays the current configuration. Show history displays the last 20 commands entered during the current cli session. Show statistics displays the telnet statistics. State disable disabl...
Page 157
5: commands and levels matchport® b/g pro embedded device server command reference 157 terminal network enters the configure-terminal level for the network. Terminal type sets the terminal type. Tunnel enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. Write store...
Page 158
5: commands and levels matchport® b/g pro embedded device server command reference 158 tunnel enters the tunnel level. = number of the tunnel line (serial port) to be con- figured. Write stores the current configuration in permanent memory. Terminal network (config-terminal:network) level commands b...
Page 159
5: commands and levels matchport® b/g pro embedded device server command reference 159 figured. Write stores the current configuration in permanent memory. Tftp (config-tftp) level commands allow file creation disable prohibits the tftp server from creating files on the file system. Allow file creat...
Page 160
5: commands and levels matchport® b/g pro embedded device server command reference 160 = number of the line (lpd serial port) to be config- ured. Modem enters the modem level for this tunnel. No clear counters unzeros all tunnel counters packing enters the packing level for this tunnel. Ppp enters t...
Page 161
5: commands and levels matchport® b/g pro embedded device server command reference 161 exit exits to the configuration level. No clear counters unzeros ip counters show history displays the last 20 commands entered during the current cli session. Show statistics shows udp statistics write stores the...
Page 162
5: commands and levels matchport® b/g pro embedded device server command reference 162 tx key index 2 selects key 2 for transmission encryption. Tx key index 3 selects key 3 for transmission encryption. Tx key index 4 selects key 4 for transmission encryption. Write stores the current configuration ...
Page 163
5: commands and levels matchport® b/g pro embedded device server command reference 163 topic init disable disables this wlan verbosity topic. Topic init enable enables this wlan verbosity topic. Topic ioctl disable disables this wlan verbosity topic. Topic ioctl enable enables this wlan verbosity to...
Page 164
5: commands and levels matchport® b/g pro embedded device server command reference 164 eap-ttls option mschap sets the eap-ttls authentication protocol option to mschap. Eap-ttls option mschapv2 sets the eap-ttls authentication protocol option to mschap v2. Eap-ttls option pap sets the eap-ttls auth...
Page 165
5: commands and levels matchport® b/g pro embedded device server command reference 165 clrscrn clears the screen. Default authentication restores the authentication method to the default value (psk). Default eap-ttls option restores the eap-ttls protocol options to the default (eap- mschap v2). Defa...
Page 166
5: commands and levels matchport® b/g pro embedded device server command reference 166 show shows the current configuration. Show history displays the last 20 commands entered during the current cli session. Username sets the value of the username. = value in characters (max 63). Validate certificat...