Full fet class ab amplifier.
Mosfet switches maintain rated power over a wide range of battery voltages pwm(pulse-width-modulated) system. 2 ohm stable stereo operation stereo, bridge mode and tri-mode system application compatible variable input level controls for each pair of channels variable high and low pass crossover cont...
When crossover mode selector is in low pass mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 50 hz - 500 hz. L ow p ass f ilter when crossover mode selector is in high pass mode, this control limits the...
When crossover mode selector is in high and low pass mode, this control limits the frequencies which will be distributed to the speakers to those above the value to which this is set within the range 50 hz - 500 hz. H igh & l ow p ass f ilter determines the mode of built-in crossover: low pass(permi...
Frequency response input sensitivity s/n ratio channel separation low pass filter bass boost control dimensions(inches) fuse(s) rms at 2 ohms at 4 ohms bridged speaker impedance t.H.D 4 ohms power peak at 4 ohms 10hz ~40khz >90db >65db 50hz~500hz 0 ~+18db (60 hz fixed) 8.66"x2.15"x9.45" 20a x 2 950w...
1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wir...
Left speaker right speaker speaker impedance 2~4 ohm to output from heat unit 2 c h a n n e l s t e r e o c o n f i g u r a t i o n 20a x 2 25a x 2 25a x 3 dct202 dct252 dct282 model fuses to car stereo auto antenna fuse.
Speaker impedance 4~8 ohm 2 c h a n n e l b r i d g e d m o d e c o n f i g u r a t i o n to output from heat unit 20a x 2 25a x 2 25a x 3 dct202 dct252 dct282 model fuses to car stereo auto antenna fuse.
To car stereo auto antenna speaker impedance 4~8 ohm left speaker 2 c h a n n e l t r i - m o d e c o n f i g u r a t i o n to output from heat unit 20a x 2 25a x 2 25a x 3 dct202 dct252 dct282 model fuses right speaker fuse.
4 c h a n n e l s t e r e o c o n f i g u r a t i o n to output from heat unit to car stereo auto antenna 4ch speaker 3ch speaker 2ch speaker 1ch speaker fuse.
4 c h a n n e l b r i d g e d m o d e c o n f i g u r a t i o n to car stereo auto antenna to output from heat unit speaker impedance 4~8 ohm speaker impedance 4~8 ohm fuse.
4 c h a n n e l t r i - m o d e c o n f i g u r a t i o n to output from heat unit fuse to car stereo auto antenna 4ch speaker 3ch speaker 2ch speaker 1ch speaker speaker impedance 4~8 ohm speaker impedance 4~8 ohm.
Stop stop 2-channel amplifier (operating in stereo) 2-channel amplifier (operating in bridged mono) yes! No! 4 ohm + _ 4 ohm + _ 4 ohm 4 ohm + _ + _ + _ + _ + _ two 4-ohm speakers, wired in stereo, will present a 4 ohm load to each channel of the amplifier. Most two- channel amplifiers will work wel...
