O p t i o w n e r ' s m a n u a l - 1 1. Contents 2. Introduction 3. Features 4. 5. Specifications 6. Amplifier installation 7. 8. Features and controls 9. 10. 11. 12. System wiring 13. 14. Troubleshooting.
O p t i o w n e r ' s m a n u a l - 2 thank you for purchasing the lanzar opti class-d amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service. The opti class-d amplifier has been designed using the latest in electr...
O p t i o w n e r ' s m a n u a l - 3 low - frequency information for subwoofer only. High efficient power stiffly regulated pwm power supplies. Mosfet switches maintain rated power over a wide range of battery voltages. Adjustable from 50hz to 150hz with a slope of 24db per octave. This allows for ...
O p t i o w n e r ' s m a n u a l - 4 90db 15hz to 150hz (+/-3db) 400 50hz~150hz, 24db/octave 15hz~40hz, 24db/octave 0~+18db 200mv to 8v 10k ohm 100 ohm 10.08" x 2.12" x 14.96" 30a x 4 0 to 180 800w mono 1000w mono 1300w mono 0.1% opti 1400d 500w mono 2600w mono n/a 90db 15hz to 150hz (+/-3db) 400 5...
1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wir...
Input line out min max 15 40 150 50 0db 18db 0 180 phase bass boost low pass level speaker pwr prot l r data link slave master mode sub sonic 0 180 150 50 0db 18db min max 15 40 subsonic bass boost level input line out l r remote power protection phase shift low pass data link slave master bridged m...
O p t i o w n e r ' s m a n u a l - 8 9. Power & protection indicators- provide instant information on status of amplifier, including short-circuit and thermal overload alerts. 7. Bridged mode 8. Bass boost remote control input 1. Line out rca jacks - the line out allows you to build multiple amplif...
Input line out min max 15 40 150 50 0db 18db 0 180 phase bass boost low pass level speaker pwr prot l r data link slave master mode sub sonic o p t i o w n e r ' s m a n u a l - 1 0 b+ rem gnd power fuses subwoofer speaker impedance 1~8 ohm to output from head unit to remote gain controller opti 150...
Input line out min max 15 40 150 50 0db 18db 0 180 phase bass boost low pass level speaker pwr prot l r data link slave master mode sub sonic input line out min max 15 40 150 50 0db 18db 0 180 phase bass boost low pass level speaker pwr prot l r data link slave master mode sub sonic o p t i o w n e ...
O p t i o w n e r ' s m a n u a l - 1 3 before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. Check for good ground connection. Check that remote dc terminal has at least 13.8v dc. Check that there is battery powe...
O p t i o w n e r ' s m a n u a l - 1 4 check for shorts on speaker leads. Check that the volume control on the head unit is turned down low. Remove speaker leads, and reset the amplifier. If the protection led still comes on, then the amplifier is faulty. Check that the minimum speaker impedance fo...
Lanzar audio inc. 1600 63rd street, brooklyn, ny 11204 (718)535-1800 www.Lanzar.Com.
