Laser Pegs NFL003 Lift the House Assembly instruction
x2 AV
v v
Each Laser Peg® is color coded on the circuit board inside
each shape. There is No LED In The 90 Degree Peg.
Laser Pegs
®
link that
allows you to connect to
other construction kits.
Triangle Power
Base
Color
Code
All additional model instructions can
be downloaded at www.LaserPegs.com
MODEL INSTRUCTIONS
Laser Pegs
®
Stackable
Laser Peg® Parts List
Construction Parts List
SQUARE
PEG
90° PEG
45° PEG
Y PEG
There is No LED In The 90 Degree Peg
x4
x4
x2
x1
x2
x4
x4
x4
x2
x2
x2
x4
x8
x4
x2
x8
x8
x2
HELMET PEG
STRAIGHT
T-PEG
SQUARE
M-M PEG
x1
x2
x2
x2
x2
x2
x1
x1
x2
x4
x2
x2
x2
x4
x6
x2
x2
x2
x2
x2
x2
x4
STACKABLE
FOOTBALL PEG
x2
x2
x2
WHEEL PEG
x4
Please read manual before you begin! Failure to
follow this manual’s instructions may result in
damage to the Triangle Power base, AC adapter
and/or Laser Pegs®. Not adhering to these
directions will void the manufacturer’s warranty.
Packing has to be kept since it contains
important information.
Compatible with other construction kits
WARNING:
CHOKING HAZARD
-
Small parts.
Not for children under 3 yrs.
Do not submerge in water.
Construction Compatible
EN71, RoHS COMPLIANT
This product complies to
all safety requirements
of ASTM F 963
For Boys And Girls
Ages 5 And Up
24 Models+
LIGHTED
CONSTRUCTION SET INCLUDES:
• 32 Laser Pegs®
• 96 Construction Parts
• Triangle Power Base
• Instruction Manual
Requires 3 AA Batteries
Batteries NOT
Included
Any creation you can build
To construct with Laser Pegs®, slide two pieces together to form a
connection. Slide each piece on and off smoothly. To build away from the
Triangle Power Base, use the peg cord in one of the top three peg holes to
illuminate your model! The 90° pegs are essential to construction but they
DO NOT ILLUMINATE.
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2013 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.com
www.LaserPegs.com
Connecting Pegs
Press button
to turn on/off
Push button to cycle
through 3 different
light settings.
Power Button
Peg Holes
AC Adapter
Connection
Remove the three Philips head
screws with a 4mm screw driver.
Requires (3AA) Batteries
Using an
AC Adapt
er
Remove all batteries
from Laser Pegs® power
base before using the
5 volt AC adapter.
When using an AC
Adapter, NEVER
place the adapter
plug into the Tri-
angle power base
top peg holes.
When Using Batteries
WARNING! Each Laser Peg® draws current from the batteries. Therefore, the more
pegs you use, the quicker you will deplete your battery power! As the power
weakens, the current will slowly fail and some Laser Pegs® will illuminate (typically
the reds and yellows) and some won’t. When the Laser Pegs® dim the Laser Pegs®
are not broken, they just need stronger batteries or an AC Adapter.
You have 3 simple options...
1. Use a 5 volt AC Adapter –available from www.LaserPegs.com
2. Change the batteries.
3. Use high quality batteries. They will last a little longer, but they will still deplete
rapidly the more laser pegs you connect!
*To avoid short-circuits, keep metal objects and
other un-authorized materials from obstructing
the peg holes.
The AC adapter and the power base are to be regularly examined for damage
to the cord, plug, enclosure and other parts, and in the event of such damage,
they must not be used until the damage has been repaired.
1. Remove screws.
2. Place three AA batteries in the correct
position - as displayed inside the Triangle
Power Base.
3. Push RED button to turn on!
4. Do not mix old and new batteries.
5. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium)
batteries!
6. Exhausted batteries are to be removed
from the power base.
7. Never connect more than 200 Laser Pegs®
8. Non-rechargeable batteries are not to be
recharged.
9. Rechargeable batteries are only to be
charged under adult supervision.
10. Rechargeable batteries are to be removed
from the toy before being charged.
11. Batteries are to be inserted with the
correct polarity.
12. The supply terminals are not to be short-
circuited.
Never connect more than 200
Laser Pegs® when using a 5 volt
(2000mA) AC Adapter.
FOOTBALL PEG
HELMET PEG
NFL Series Helmet and Football Peg
Your NFL Series Laser Pegs® kit comes with a set of licensed NFL team
decal stickers. There are two stickers per team included. These stickers can
be affixed to the sides of the Helmet Peg or the the Football Peg.
Your NFL Series Laser Pegs® kit also includes bonus material from the
NFL Rush Zone.
Affixing NFL Team Logo Stickers
There will be two (2) sheets of NFL logo stickers included inside each
individual NFL Series Laser Peg® kit. These sheets of stickers will have a
set of two (2) team logos that can be placed on either side of the Helmet
or Football Peg. Before applying stickers to the pegs, it is advisable to first
wipe any dirt, oil or residue that maybe on the surface of the pegs due to
handling with a clean dry cloth. This will help ensure proper adhesion to
the peg’s surface.
The NFL Series Laser Pegs® kit includes the Football and Helmet Peg.
These shapes can be used with any other existing Laser Pegs® kit. Both the
Football and Helmet Pegs illuminate.
Supplied NFL team stickers will be reflected so that they will remain in
the correct orientation when they are applied to either side of the Helmet
or Football Pegs.
WARNING!
Do not ingest stickers or backing sheet. This could be potentially
dangerous and may cause severe injury. So keep away from small children.
Apply Sticker to
side of Helmet Peg.
Apply Sticker to side
of Football Peg.
The NFL Series
Laser Pegs® kit
Football Peg has only
one mating end.
The NFL Series
Laser Pegs® kit
Helmet Peg(s) Is
included.
Additional stickers are included
LIMITED
EDITION
When applying the NFL Series
Laser Peg® Team Logo Stickers
TRIDENT PEG