Laser Pegs Zippy 004 Assembly Instruction Manual
Environmental Phenomena
* The unit may malfunction if subjected to radio-frequency interference. It SHOULD revert to
normal operation when the interference stops. If not, it may become necessary to turn the power
off and back on, or remove and reinstall the batteries.
* In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory,
requiring the user to reset the devise by removing and reinstalling the batteries.
Please read this manual before you begin!
Failure to follow this manual’s instructions may
result in damage to the Zippy Do® Power Base
and/or the Zippy Do® pieces. Not adhering to
these instructions will void the manufacturer’s
warranty. The packaging must be kept because
it contains important information.
This manual is copyright and cannot be reproduced or used online without Laser
Pegs®Ventures LLC permission. Copyright 2014 © All Rights Reserved US Patent
#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures
LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: Support@LaserPegs.com
Compatible with other construction kits
www.LaserPegs.com
WARNING:
CHOKING HAZARD
-
Small parts.
Not for children under 3 yrs.
Do not submerge in water.
Construction Compatible
EN71, RoHS COMPLIANT
This product complies to
all safety requirements
of ASTM F 963
Zippy Do® Parts List
by
To construct with Laser Pegs®, slide two pieces together to form
a connection. Slide each piece on and off smoothly. (Laser Pegs®
pieces sold separately).
Connecting Pegs
*To avoid short-circuits, keep metal objects and other
unauthorized materials from obstructing the peg holes.
Remove the Phillips head
screw with a 4mm screw
driver.
Requires
3-LR44 Button Cell
Batteries
Screw
Battery Compartment
Cover
Batteries
Power Switch
Battery
Compartment
1. Remove the Phillips head screw.
2. Remove the Battery Compartment Cover.
3. Place three (3) LR44 batteries in the correct
position. (Batteries are to be inserted with the correct
polarity).
4. Replace the Battery Compartment Cover.
5. Replace the Phillips head screw.
6. Slide Power Switch to turn on!
7. Do not mix old and new batteries.
8. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (nickel-cadmium, NiMH) batteries!
9. Exhausted batteries are to be removed
from the power base.
10. Batteries should be recycled or disposed of as per
state and local guidelines.
11. Non-rechargeable batteries are not to be recharged.
12. Rechargeable batteries are only to be recharged under
adult supervision.
13. Rechargeable batteries are to be removed from the
toy before being recharged.
14. The supply terminals are not to be short-circuited.
15. Do NOT throw batteries into fire!
Replacing Batteries
x1
x1
x1
For Boys And Girls
Ages 3 And Up
LIGHTED
CONSTRUCTION SET INCLUDES:
• 21 Construction Parts
• Zippy Do® Power Base
• Instruction Manual
Requires 3-LR44 Batteries
Batteries
Included
12 Models+
004
ANY CREATION YOU CAN BUILD
x3
x1
underside of Zippy Do® Power Base
Power Switch
Slide Power Switch to turn on/off/flash
Slide Power Switch to cycle through different light settings.
®
This Product contains a button battery. If swallowed, it could
cause severe injury or death in just 2 hours.
Seek medical attention immediately.
The toy is not to be connected to more than
the recommended number of power supplies
x1
x2
x1
x1
x2
x1
x2
x1
x4
WARNING: STROBE LIGHTS
MAY CAUSE SEIZURES
Connects to other
Laser Pegs® pieces
BATTERIES ARE TO BE INSERTED
INTO THE TOY BY AN ADULT ONLY!
ONLY ADULTS SHOULD INSTALL THE BATTERIES
CAR
PLANE
HELICOPTER
SKI PLANE