1. DL manuals
  2. Laser Technology
  3. Measuring Instruments
  4. TruPulse 200X
  5. Quick Reference Field Manual

Laser Technology TruPulse 200X Quick Reference Field Manual

Summary of TruPulse 200X

  • Page 1

    Trupulse ® 200x quick reference field guide lti part #0144893.

  • Page 2: Lti Technical Support:

    Lti technical support: toll free: 1.877.696.2584 phone: 1.303.649.1000 email: support@lasertech.Com web: www.Lasertech.Com lti hours of operation: monday through friday 8:00 am to 5:00 pm (mst) (excluding holidays) lti corporate headquarters: 6912 south quentin street centennial, co 80112 usa lti yo...

  • Page 3: Trupulse

    Trupulse ® 200x display indicators: inclination horizontal distance vertical distance closest slope distance farthest missing line height continuous laser status battery life feet meters yards degrees percent filter upper and lower main display ( ) cross hair / aiming point inches centimeters gate.

  • Page 4: 1-Shot Distance:

    Measured by trupulse: 1-shot distance: 2-shot missing line: 2-shot height: 3-shot height: trupulse ® 200x values & key code: = horizontal distance = slope distance = vertical distance = height = inclination = missing line = fire button = mode button = forward button = back button ( ) = in-scope top ...

  • Page 5: [1] Press         Until

    Change display brightness level: change units of measurements: [1] press until ( ) . [2] press until desired brightness level ( ) . [3] press ( ) to accept the brightness level. [1] press until ( ) . [2] press to scroll through unit options ( ) , ( ) . [3] press to accept the units of measurement ( ...

  • Page 6: Filter Mode:

    Filter mode: continuous mode: [1] press until ( ) . [2] press to choose ( ) or ( ) . [3] press to accept selection. [1] press until ( ) . [2] press to choose ( ) or ( ) . [3] press to accept selection. When filter mode is on, make sure you have the foliage filter attached to the receive lens and tha...

  • Page 7: Targeting Mode:

    Targeting mode: [1] press until ( ) . [2] press to choose mode: standard ( ) ; farthest ( ) ; closest ( ) . [3] press to accept selection. Helpful tips: [1] targeting mode is not accessible when filter mode is on. [2] filter symbol , continuous mode symbol and any other mode symbol will show on righ...

  • Page 8: (         )

    [1] the minimum gate values are 1 meter, 4 feet and 2 yards. The maximum gate values are 500 meters, 1640 feet and 500 yards. [2] to increase gate value when gate is already on, press until ( ) then press again to change increments. Helpful tips: gate function: in this mode, the trupulse 200x will o...

  • Page 9: [1] Press        Until

    [1] press until ( ) . [2] press to choose bluetooth on ( ) , off ( ) or enc ( ) . [3] press to accept selection. Turn on or off bluetooth ® : [1] each time the tp200x is powered on, it will retain the same settings that were last set/used. [2] to perform a factory reset, simultaneously press-and-hol...

  • Page 10: Measure Distance:

    Measure distance: in hd mode, it will automatically measure sd and inc, then calculate vd and hd. The values will output via serial and/or bluetooth. Measurements are from the center of laser to target. [1] press until ( ) is displayed. [2] aim at target where you have a clear line of sight then lon...

  • Page 11: Measure Height In 3 Shots:

    Measure height in 3 shots: this routine is ideal for flat, vertical objects that do not lean. To shoot through brush, use the filter mode, foliage filter and a reflector. [1] press until ( ) is displayed. [2] aim anywhere you have a clear line of sight and long press ( ) [3] ( ) aim to the bottom an...

  • Page 12: Measure Height In 2 Shots:

    Measure height in 2 shots: the 2-shot ht works well on leaning objects but requires a clear line of sight for both shots. [1] press until ( ) is displayed. [2] aim at the top of the target and long press ( ) . Note the value. [3] aim to the bottom of the target and long press ( ) . Note the value. [...

  • Page 13: Measure 2-D Missing Line:

    Measure 2-d missing line: position yourself where shot 1 and 2 are made looking in the same direction with a clear line of site to both targets. The exception is the vd solution, which will always be accurate no matter which direction shot 1 and 2 are taken. [1] press until ( ) is displayed. [2] aim...

  • Page 14

    Www.Lasertech.Com.