1. DL manuals
  2. Laser UK
  3. DJ Equipment
  4. club scene
  5. User Manual

Laser UK club scene User Manual

Manual is about: tri-color laser show system

Summary of club scene

  • Page 1

    User manual hadfield management ltd please read this manual carefully before you initially start-up!.

  • Page 2

    1 open the box for checking thank you for choosing of this product club scene tri-color laser show system. In order to use this product safety and reasonable, please read over this manual carefully before use and the operation must strictly according to this manual to avoid any damage to the product...

  • Page 3

    Danger laser radiation! Avoid direct eye exposure! Laser radiation can cause eye damage and/or skin damage all protective measures for a safe operation of this laser must be applied. Safety instructions - if the device has been exposed to drastic temperature fluctuation, do not switch it on immediat...

  • Page 4

    - if this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. - furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, product rear view function table: 3 1 mic audio...

  • Page 5

    10 ilda in ilda standard signal input 11 ilda thru ilda standard signal through 12 on/off key switch for power supply 13 ac in ac 110-240v 50/60hz operation instrution 1. Sound&dmx control mode you can choose sound or dmx control mode through the 10 th switch: while it is switched to off position, t...

  • Page 6

    1.2 dmx control mode for dmx mode, the 10th dip switch must be on. Then, set the dmx base address with the binary system “0” or “1” through switch 1-9 examples: 5 dmx address dmx address 1 33 65 113 161 225 dmx base adds. 1-10 setting: (on is 1, off is 0) 1 ~ 10 function 0,0,0,0,0,0,0,0,0,0 sound co...

  • Page 7

    The device has 10 operating channels. If you set the first on dmx address “1”, the next dmx device can follow at address 20. Dmx channels assignment: 6 channel dmx512 value function 0--63 sound control (3-10ch useless) 64--127 auto mode (3-10ch useless) 128--191 dmx control 1.Control mode 192--255 a...

  • Page 8

    2. Sd card controlling mode 2.1 sd card controlling settings panel the panel can be used to access some important parameters for the ilda projector. If the memory of the panel is empty, it displays “err” at power-on. At normal function, if parameters are set correctly, the panel displays the actual ...

  • Page 9

    Sequences normally will not be interrupted. Limits dmx base address 1 – 512 intensity 0 – 99 orientation 0 – 7 limits will be controlled automatically by the panel. If trying to set a value beyond the limits, the panel automatically corrects to an allowed value during input. Intensity for the projec...

  • Page 10

    2.3 dmx channels assignmet 9 channel1: show select l this channel is used for show selection; one of the first 16 shows (including pause) can be selected. Channel2: show select h 16 banks of shows, 16 shows each, 256 shows can be selected using this function. Channel3: size (projection size) when yo...

  • Page 11

    When using own cards or reformat cards by using a pc with windows** operating system, it is not ensured, that the cards are formatted fat16. Depending on the memory size of the card, windows** can format these to fat12, fat16 or fat32 file system. The poseidon will not work with other file systems t...

  • Page 12

    Fig. 1configuration software dmx-base address input here the dmx-base address, from where the group of 16 control channels starts. 11 possible values are 1-512. Maximum sum of base address plus highest used control channel is 512. Any overflow will be watched by the software and a message will be di...

  • Page 13

    Fig. 3 dmx-channel selection showselect l this dmx-function cannot be disabled! Input here the channel for show selection. When just this channel is used for show selection, one of the first 16 shows (including pause) can be selected. Showselect h input the channel number corresponding to this funct...

  • Page 14

    Input the channel number corresponding to this function here. When you change size by the use of dmx-control, a fader position of 0 (minimum) can cause a standing laser beam. This can be a dangerous condition! It is recommended not to use this dmx-control and use the fixed global value instead, or t...

  • Page 15

    Fig. 4showtable when clicking in a row under filename, a dialog opens for selecting a file. The same file can be used in different rows of the table. Watch that the card (removable media) is selected as the path. Then you can be sure, that your show file is available on the card. It is also possible...

  • Page 16

    Fig. 5 fig. 6 speed pps framerepeat (fig. 7) this value only will be used when framerepeat is not controlled by dmx-channel. Fig. 7 framerepeat displaymode (fig. 8) here, one of four possible displaymodes can be selected. Pause is fixed to one mode and the trigger shows only offer 2 modes. Displaymo...

  • Page 17

    These are complete and interruptable. Complete the current running show will be outputted completely, before any new showselection is possible. Interruptable the current running show will be aborted, when a new show is selected. The following combinations are possible: loop/complete the current show...

  • Page 18

    Interface to the ilda in connector on the rear panel using the included pc controlling cable. If you want to make your own cable, you should comply with the blow signal definition table of ilda-db-25f pinouts. Signal name pin notes x+ 1 -5 to +5v y+ 2 -5 to +5 v red+ 5 0v to 2.5v green+ 6 0v to 2.5v...