1. DL manuals
  2. LaserLine
  3. Car Alarm
  4. 212
  5. User Manual

LaserLine 212 User Manual

Summary of 212

  • Page 1

    ® gb 290i2/212/291/213 insurance approved alarm/immobiliser user guide car ala rm systems isut291-213uk.P65 11/05/2006, 18.53 1.

  • Page 2

    Warning alarms must not be steam cleaned or pressure washed. Before carrying out any electrical work on the vehicle isolate the system by removing system fuse/vehicle battery or damage to the alarm may result! These systems are manufactured from the highest quality components to ensure a long troubl...

  • Page 3

    Operating instructions you would have received from your installer, two remote controls (see fig. 1) and have been shown the location of the status led (fig. 2). Functions button a: arming/disarming of the alarm (290i2/ 212); button a: arming/disarming of the alarm and immobiliser (291/213); button ...

  • Page 4

    Disarming the alarm system press button a (arm/disarm), located on the right of the remote control (see fig. 1). The direction indicator lights will flash once and the alarm may give one audible tone (programmable function) generated at the same time to indicate that the alarm system has been disarm...

  • Page 5

    Immobilisation (291/213 only) when the alarm system is armed, an internal immobiliser (921k) isolates the vehicle starting circuits (e.G. Starter motor/fuel pump) to prevent running of the vehicle. Passive immobilisation (291/213 only) the internal immobiliser (921k) activates automatically after 30...

  • Page 6

    This function only applies if there is no optional electronic key. If all the remote controls have been lost or are malfunctioning, you can disarm the alarm system using the “emergency pin code”. How to know your emergency pin code to display the emergency pin code (pin code), wait 10 seconds after ...

  • Page 7

    How to disarm the alarm using the emergency pin code if your transmitter does not work correctly or has been lost, to disarm the alarm system you must insert the “emergency pin code” by doing the following: 1) with the alarm armed, activate the siren by opening the door on the driver’s side; 2) ente...

  • Page 8

    Example: the code to be inserted is 5 6 0 5 4. First digit 5 - wait 5 flashes for the first digit. After the fifth flash has been completed and the led has turned off, immediately turn on the ignition key for 1 second. Turn the ignition off and after a pause, the led will flash for the next digit of...

  • Page 9

    This facility confirms the correct operation of interior/doors/boot/bonnet detection circuits. This is indicated by a series of audible tones/illumination of the direction indicators and a series of flash- ing of the dashboard led, when one of the circuits is triggered within the pre-alarm time. To ...

  • Page 10

    Alarm auto-diagnostics if an alarm was generated while the system was armed, when the system is disarmed the direction indicator lights will flash briefly (½ second) and an audible tone will be produced to indicate that an alarm condition has occurred. At any time while the system is disarmed and th...

  • Page 11

    If your alarm sounds for no apparent reason, please refer to the diagnostics flash codes for possible condition. Possible causes of the alarm condition could be: - vehicle has been tampered with. - windows/sunroof are not fully closed. - doors/boot/bonnet are not fully closed. - check that the air v...

  • Page 12

    Courtesy lights or the external sidelights, illuminating the area near the car. Pressing button “c” again prior to the 10 seconds causes the lighting to switch off (vehicle with courtesy lights delay system may take longer to switch off). Comfort function* (only for vehicle equipped with comfort clo...

  • Page 13

    Additional siren (290i2/291 only)* this function allows the alarm to be connected to an additional siren/vehicle horn/paging system and can be programmed to obtain a continuous or intermittent output for the entire alarm cycle. Type of sound (290i2/291 only)* two different types of sound can be prog...

  • Page 14

    Auto-learning function allows you to program new remote controls/electronic keys or cancel lost remote controls/electronic keys. To carry out the auto-learning procedure, at least one functioning remote control or electric key must be available. Then do the following: Œ open the door on the driver’s...

  • Page 15

    Battery replacement 1 open the remote by inserting a screwdriver between the two cases of the remote control (fig. 1). Lever to separate the two plastic cases. 2 remove the printed circuit board (fig. 2). 3 remove used battery (fig. 3). 4 insert the new battery taking care to only touch the sides (n...

  • Page 16

    290i2/212 power supply ............................................................................................ 9-15v negative ground current absorbed with alarm armed (with ultrasonic) ................................................ Current absorbed with alarm disarmed (with ultrasonic) .........

  • Page 17

    290i2/212 test approval numbers 290i2 - mirrc reference number: category 2 - 1 tu2 - 1183/1100 290i2 -mirrc reference number: category l2 - 1 tul - 45/1200 212 - mirrc reference number: category 2 - 1 tu2-1368/0506 212 - mirrc reference number: category l2 - 1 tul1-134/0506 291/213 test approval num...

  • Page 18

    Product warranty covers units to be free from defects in manufacture for the lifetime ownership of the original vehicle, in accordance with the terms and conditions of this warranty document. Any product, which is deemed to be defective, will be replaced or repaired. Accessories including remote con...

  • Page 19

    Warranty will not be valid due to the following: 1. Poor response to transmitters due to abnormally high electromagnetic interference. 2. Low battery voltage in transmitters. 3. Abuse or mistreatment of any product or accessory. 4. Loss or damage due to accident, fire, lightening, explosion, flood o...

  • Page 20

    Service inspection 1 yrs 2 yrs 3 yrs 4 yrs please note 7 yrs 6 yrs 5 yrs installer’s stamp cert. No. Reg. No. Date. Signature the above service inspection must be carried out in order to ensure the validity of the customer lifetime warranty installer’s stamp cert. No. Reg. No. Date. Signature instal...

  • Page 21

    Alarm/immobiliser model no. ………...…………….............Make………………………..............……. Accessories fitted ………………………….............................Model………………….....................…… date of installation……………………………….....................Reg.No. ……….…..........……….....……. Customer name……………………………….............

  • Page 22: Return To:

    Return to: laserline direct limited 33, craven court winwick quay warrington cheshire wa2 8qu isut291-213uk.P65 11/05/2006, 18.53 22.

  • Page 23

    Isut291-213uk.P65 11/05/2006, 18.53 23.

  • Page 24

    Our commissioned sales and support agents in the uk are laserline direct limited 33, craven court - winwick quay - warrington - cheshire wa2 8qu dealer stamp cod. Isut291-213uk filename: isut291-213uk.P65 isut291-213uk.P65 11/05/2006, 18.53 24.