1. DL manuals
  2. LaserLine
  3. Car Alarm
  4. 996
  5. Installation Manual

LaserLine 996 Installation Manual

Manual is about: Car Alarms Systems

Summary of 996

  • Page 1

    English 13 cod. Is 996e installation guide mod. 996 kit car alarms systems is996v2 ita-ing.Pm6 05/03/98, 16.27 13.

  • Page 2

    English 14 installation guide look the car's handbook up before disconnecting battery negative pole, paying particular attention to the air-bag device and audio equipment codes. Handle the central unit with care. - yellow wires: connect one yellow wire to the right direction indicator and the other ...

  • Page 3

    English 15 operating instructions alarm armed: push button 1of the remote control. Arming is signalled by two flashes of the direction lights and two acoustic signals (if ref. 904 has been connected to orange wire).When the alarm has armed, the led fitted in the dashboard flashes. Alarm disarmed: pu...

  • Page 4

    English 16 self diagnostic led functions this function lets you verify the cause of an alarm condition. When the alarm is disarmed by radio control, observing the led will allow you to identify the cause of the alarm condition. Led off: no alarm occured 2 flashes/pause: an alarm caused by ultrasonic...

  • Page 5

    English 17 self coding remote control and electronic keys handsets in case you lose a remote or need to code a new one your installer will be able to quickly re-code and replace it in the following way: l ) ensure alarm is disarmed with the original remote handset. 2) turn ignition to on position. 3...

  • Page 6

    English 18 dip switch coding table ! Attention • when the alarm is disarmed no function is activated. • when ignition key is on it is not possible to arm the alarm. • if there are three consecutive alarm conditions caused by the same detector (ultra- sonics sensor/push buttons), after the third cicl...

  • Page 7

    English 19 diagram 1 electronic key white red ground j18 j17 j24 red(siren) battery ignition switch direction light door/boot contact windows closers module art. 811,824,828 positive output during the alarm (max. 3a) engine immobilisation siren connection central door locking ultrasonic sensor white...

  • Page 8

    English 20 j8-j9: use for the second engine stop.Locate supply to coil,fuel pump or electronic ignition module.Cut this wire. Connect j9 to the supply side of the cut wire and connect j8 to the load side of the cut wire. Solder and insulate joints carefully. J7: connect to a quality ground. Do not r...

  • Page 9

    English 21 diagram "3/a" for vehicles with multi point centralised door locks (negative pole type) green/black- yellow/black: connect to ground grey/black: negative impulse for closing brown/black: negative impulse for opening light blue/black - red/black: not used diagram "3/b" for vehicles with mu...

  • Page 10

    English 22 place dip switches before making connections diagram "3/b" positive pole type diagram "3/a" negative pole type place dip switches before making connections dip switch no. 2 off: 1 second pulse dip switch no. 2 on: 3 seconds pulse dip switch no. 1 on: 25 seconds pulse (lock only) do not us...

  • Page 11

    English 23 place dip switches according to the diagram before making connections diagram "3/d" control for electro-pneumatic motor diagram "3/c" control only from one position place dip switches according to the diagram before making connections cut door pump green-black grey-black brown-black yello...

  • Page 12

    English 24 996kit meet the requirements of the 89/336 directive concerning the electromag- netic compatibility (emc) and ets 300/220 rule concerning the radio frequency device. Insert the wire coming from the alarm as shown in the picture below important the recommended position of the siren in the ...