Lasko 5775 Important Instructions & Operating Manual - page 2
FUNCIONAMIENTO
(Figuras 1 a 3)
1. Cuidadosamente retire el Calefactor de la bolsa y de la caja.
2. Coloque el Calefactor sobre una superficie firme y plana.
Los
tacos de plástico o hule, tales como las patas de esta unidad,
pueden pegarse a la superficie de los muebles y/o a los pisos de
madera. La unidad podría dejar un residuo capaz de oscurecer,
manchar o dejar marcas permanentes en el acabado de ciertas
superficies de muebles, incluyendo superficies de madera y/o
pisos de madera.
3. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes en
este estado podrían sobrecalentarse y representar un
peligro de incendio grave; si queda cubierto por una
cortina o tela, el peligro de incendio es todavía mayor.
4.
Cuando el Calefactor se conecte por primera vez, se oirá un
“bip” y la Luz de Encendido se encenderá indicando que hay
electricidad en la unidad. La Luz de Encendido permanecerá
encendida hasta que el Calefactor sea desconectado del
tomacorriente eléctrico.
5.
ENCIENDA el Calefactor oprimiendo el Botón de Encendido
.
6.
Cuando se lo encienda por primera vez
, el Calefactor estará en
calor Alto (1500 vatios) en Máx. (La luz Alta estará encendida
permanentemente y la luz de Máximo estará titilando).
7. Oprima el Botón de Encendido una vez más y el Calefactor
estará en Calor Bajo, indicado por la luz permanente junto a
Bajo.
8. Oprimir el Botón de Encendido por tercera vez APAGARÁ
el Calefactor.
9. Cuando el Calefactor está APAGADO, la luz roja en la parte
frontal del Calefactor permanecerá encendida hasta que el
Calefactor sea desconectado del tomacorriente eléctrico.
ADVERTENCIA:
EL TEJIDO DE MALLA PLASTICO DE LA
PARRILLA ESTÁ CALIENTE CUANDO EL CALEFACTOR ESTÁ
EN FUNCIONAMIENTO.
Función de Oscilación:
Oprimir el Botón de Oscilación ( ) le permitirá al Calefactor
oscilar hacia atrás y hacia delante. Para detener la oscilación,
vuelva a oprimir el Botón de Oscilación ( ). Cuando el
calefactor esté en control automático de temperatura, la función
de oscilación se detendrá cuando se alcance la temperatura
fijada y reiniciará cuando el calefactor vuelva a encenderse.
Rev. D 3/14
2
5775ES
7
5775ES
Rev. D 3/14
MODELO 5775
Función de Temperatura
(Figura 2)
1. Para ambientar la habitación a una temperatura específica, oprima
el Botón de Temperatura (TEMP) hasta la posición deseada. La
luz debajo de la temperatura seleccionada continuará titilando
hasta que la habitación alcance la temperatura deseada. Cuando
el calefactor esté colocado en la posición MAX, la unidad no
se apagará cuando. Para mayor eficiencia, el termostato sólo
funcionará en calor ALTO.
Función de Temporizador
(Figura 3)
1. La Función de Temporizador puede ser activada cuando la
pantalla del Calefactor se encuentre en cualquier velocidad
o temperatura. Esta función le permite a usted seleccionar la
cantidad de tiempo que el Calefactor estará en funcionamiento
antes de apagarse automáticamente, de 1 hora a 7 horas. Oprimir
el Botón de Temporizador aumentará la cantidad de tiempo, en
combinaciones de 1,2 y 4 horas. Oprimir el botón continuamente
resultará en que el temporizador quede fijado para un lapso de
7 horas. El Calefactor se apagará cuando el tiempo fijado haya
transcurrido. La unidad puede ser apagada oprimiendo el Botón
de Encendido. NOTA: Cuando el botón de temperatura esté
colocado en la posición MAX, la unidad se apagará cuando
el período de tiempo haya expirado.
Función de Temperatura
Figura 2
Figura 3
Función de Temporizador
Botón de
Temporizador
Botón de
Temperatura
SAVE THESE INSTRUCTIONS
• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT
PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET
ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT
PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON SAME CIRCUIT AS HEATER.
• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS
TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING.
IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
• MakecertainthatthepowersourceconformstotheelectricalrequirementsoftheHeater.
• ExtremecautionisnecessarywhenanyHeaterisusedbyornearchildrenorinvalids.TheHeatershouldnotbeleftoperatingunattended.
Never leave children unattended when the heater is on or plugged in.
• Thisappliancehasapolarizedplug(onebladeiswiderthantheother).Toreducetheriskofelectricshock,thisplugisintendedtofit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
• DONOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where
flammable or explosive chemicals are stored, or in wet atmospheres.
• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
• AlwaysunplugHeaterwhennotinuse.UnplugpowercordbeforeservicingormovingtheHeater.
• Donotinsertorallowfingersorforeignobjectstoenteranyventilationorexhaustopeningasitmaycauseanelectricshock,fire,or
damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
• Donotblockairintakesorexhaustinanymanner.Donotplaceonsoftsurfaces,likeabed,whereopeningsmaybecomeblocked.
Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug
the power cord.
Read all instructions before using this Heater.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
WARNING
CAUTION
• AlwaysplacetheHeateronastable,flat,levelsurfacewhenoperating,toavoidthechanceoftheHeateroverturning.LocatethePowerCordso
the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners,
or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
• ThisHeaterisHOTwheninuse.Toavoidburns,donotletbareskintouchhotsurfaces.AlwaysusehandlewhenmovingthisHeater.Keepcom-
bustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep
them at least 1 foot (0.3 m) from the sides and rear.
• ThisHeaterisnotintendedforuseinwetordamplocations.ThisHeaterisnotintendedforuseinbathrooms,laundryareasandsimilarindoor
locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
• DONOT use Heater outdoors.
• ThisHeaterisnotsuitableforuseinagriculturalfacilitiesincludingareaswherelivestock,poultryorotheranimalsareconfined.Pleaserefer to
National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricul-
tural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
• ThisHeaterisnotsuitableforuseinhazardouslocations.PleaserefertoNationalElectricCode(NEC)Article500orapplicablestateorlocal
codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS
OF NEC ARTICLE 500 (2008).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
theinterferencebyoneormoreofthefollowingmeasures:•Reorientorrelocatethereceivingantenna.•Increasetheseparationbetweentheequip-
mentandreceiver.•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.•Consultthedealeror
an experienced radio/TV technician for help. The user is cautioned that changes and modifications made to the equipment without the approval of
manufacturer could void the user’s authority to operate this equipment.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
WARNING
Pantalla del calefactor
Luz de Encendido
Figura 1