DL manuals
Lawn-Boy
Snow Blower
33005
Operator's Manual

Lawn-Boy 33005 Operator's Manual

Manual is about: Lawn-Boy Insight Series Snowthrower

Page of 16

Download

Print this page

Bookmark us

Form No. 3353-639 Rev A

Insight™ Series Snowthrower

Model No. 33006—Serial No. 260000001 and Up

Operator's Manual

Introduction

Read this information carefully to learn how to operate and

maintain your product properly and to avoid injury and

product damage. You are responsible for operating the

product properly and safely.

You may contact Lawn-Boy directly at www.Lawn-Boy.com

for product and accessory information, help finding a

dealer, or to register your product.

Whenever you need service, genuine Lawn-Boy parts, or

additional information, contact an Authorized Service

Dealer or Lawn-Boy Customer Service and have the

model and serial numbers of your product ready. Figure 1

identifies the location of the model and serial numbers on

the product. Write the numbers in the space provided.

G001113

Figure 1

1. Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has safety

messages identified by the safety alert symbol (Figure 2),

which signals a hazard that may cause serious injury or

death if you do not follow the recommended precautions.

Figure 2

1. Safety alert symbol

This manual uses 2 other words to highlight information.

Important calls attention to special mechanical information

and Note emphasizes general information worthy of special

attention.

Warning

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

This spark ignition system complies with Canadian

ICES-002

The enclosed

Engine Owner’s Manual

is supplied

for information regarding the US Environmental

Protection Agency (EPA) and the California Emission

Control Regulation of emission systems, maintenance,

and warranty. Replacements may be ordered through

the engine manufacturer.

Safety

This snowthrower meets or exceeds the B71.3

specifications of the American National Standards

Institute in effect at the time of production.

Read and understand the contents of this manual

before the engine is ever started.

This is the safety alert symbol. It is used to alert you

to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible

injury or death.

Improperly using or maintaining this snowthrower

could result in injury or death. To reduce this potential,

comply with the following safety instructions.

The following instructions have been adapted from the

ANSI/OPEI standard B71.3-2005 and the ISO 8437:1989

standard.

This snowthrower is capable of amputating hands and feet

and throwing objects. Failure to observe the following

safety instructions could result in serious injury.

Training

•

Read, understand and follow all instructions on the

machine and in the manual(s) before operating this unit.

Be thoroughly familiar with the controls and the proper

use of the equipment. Know how to stop the unit and

disengage the controls quickly.

8111 Lyndale Avenue South

Bloomington, MN 55420

Register at www.Lawn-Boy.com.

Original Instructions (EN)

Printed in the USA

1 2 3 4 5 6 7 Next › »

Summary of 33005

Page 1
Form no. 3353-639 rev a insight™ series snowthrower model no. 33006—serial no. 260000001 and up operator's manual introduction read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the prod...
Page 2: Preparation
• never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction. • keep the area of operation clear of all persons, particularly small children. • exercise caution to avoid slipping or falling. Preparation • thoroughly inspect the area where th...
Page 3: Maintenance And Storage
Maintenance and storage • check all fasteners at frequent intervals for proper tightness to be sure the equipment is in safe working condition. • never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or cloth...
Page 4
104-4135 105-1978 reorder part no. 108-7339 4.
Page 5: Setup
105-1981 reorder part no. 105-3523 110-3417 setup 1. Installing the upper handle 1. Remove the handle knob (figure 3). G001285 1 2 figure 3 1. Handle knob 2. Handle rod 2. Remove the handle rod from the handle (figure 3). 3. Attach the upper handle to the lower handle (figure 4). G001286 figure 4 5.
Page 6: 2. Adjusting The Handle
4. Hold the upper handle in place and install the handle rod from the left side of the upper handle (figure 5). G001287 figure 5 5. Install the handle knob on the handle rod and tighten the knob until it is snug. 6. Adjust the handle height if necessary. Refer to adjusting the handle height. 7. Chec...
Page 7: Product Overview
Product overview g001164 1 2 3 4 5 6 7 8 figure 9 1. Discharge chute 5. Control panel 2. Chute handle 6. Handle knob 3. Control bar 7. Rotor blades (inside the housing) 4. Upper handle 8. Fuel tank cap 1 2 3 4 5 6 g001165 figure 10 1. Key switch 4. Recoil start 2. Primer 5. Cord connection 3. Electr...
Page 8: Starting The Engine
Starting the engine 1. Turn the ignition key clockwise to the on position (figure 13). G001276 figure 13 2. Move the choke lever to the right (figure 14). G001277 figure 14 3. Firmly push in the primer 2 times with your thumb, holding the primer in for a second before releasing it each time (figure ...
Page 9: Starting The Rotor Blades
Starting the rotor blades to start the rotor blades, hold the control bar against the handle (figure 19). G001283 figure 19 stopping the rotor blades to stop the rotor blades, release the control bar (figure 20). G001284 figure 20 adjusting the discharge chute to adjust the discharge chute and the c...
Page 10: Maintenance
Maintenance note: determine the left and right sides of the machine from the normal operating position. Recommended maintenance schedule(s) maintenance service interval maintenance procedure after the first operating hour • check the control cable both initially and after the first hour of operation...
Page 11: Storage
Adjusting the cable 1. Unhook the end of the control cable spring from the control bar (figure 24). G001290 1 figure 24 1. End of control cable spring 2. Move the z-fitting to a higher or lower hole om the adjuster link as needed to obtain the 6-1/2-inch (16.5 cm) gap between the control bar and the...
Page 12
6. Choke or prime the engine, start it a third time, and run the engine until it will not start. 7. Slowly pull the recoil starter until you feel resistance due to compression pressure, then stop. 8. Release the starter tension gradually by allowing the rope to go back slowly to prevent the engine f...
Page 16
Insight™ snow products the lawn-boy no-worry waranty a warranty (limited warranty for commercial use) conditions and products covered lawn-boy, inc. And its affiliate, lawn-boy warranty company, promise to repair any lawn-boy product used for residential purposes* if defective in materials or workma...