Lawn Genie 416LG Installation And Operating Manual - page 4
Step
2:
Step
3:
PROGRAM WATERING CYCLE START TIMES
DISPLAY EXAMPLE
CYCLE
or
PM
START TIME
Upon power-up cycle No. 1 will preset with a time of 2:00 A.M. You can
enter into memory up to three start times using the
key to change
cycle numbers and numbered keys to program the start times. Start times
programmed will repeat once every 24 hours. At each cycle start time
Stations 1 through 6, programmed to water in Step 3, will water sequen-
tially. NOTE: There must be a minimum of one minute between the end of
the last station's watering and the next start time. lf an overlap does occur
the next start time will be bypassed.
EXAMPLE: Cycle start time C1: 200A
Watering time 10 minutes/station
For 6 stations : 60 minutes.
Next possible Cycle start time C2: 301A
A.
B.
C.
D.
E.
F.
G.
H.
I.
Press Cycle No. 1 is now displayed
Press three or four numbered keys for t i m e
of day.
Press
t o c h a n g e t h e d i s p l a y e d A o r P .
Press
Cycle No. 1 is now entered into memory.
Press
to display Cycle No. 2.
Repeat Steps B, C and D for the second start time.
Press
to display Cycle No. 3.
Repeat Steps B, C and D for the third start time.
Press
lo return the display back to the clock.
IF ONLY ONE START TIME IS DESIRED. PERFORM
STEPS A, B , C, D AND I ONLY.
NOTE: If you press a wrong key press
then re-enter
the correct time. If you should program an invalid time,
NOTE: If you press a wrong key press
then re-enter the
such as 13:00, upon pressing
the display will go
correct program number and watering run time. If you should
blank except for an "E", indicating an error. Press
program an invalid program number, such as 3, upon pressing
and repeat Steps B and D.
the display will go blank except for an "E" indicating
an error. Press clear and repeat Steps B, C and D.
PROGRAM STATION PROGRAM NUMBERS
AND WATERING
RUN TIME
STATION WATERING
CHART
- -
.
KEY NO. PROGRAM
. . _
0 NO
I
. .
DISPLAV EXAMPLE
The Dual Program capability of the control can be achieved as follows:
Divide the valve stations to satisfy your watering needs.
Example:
Sta-
tions 1 through 4 Program 1 (lawn), and Stations 5 and 6 Program 2
(shrubs). These groups of stations may be watered independenlty of
each other or together by using an appropriate program number in Step 4.
Upon power-up all six stations will be preset with Program 1 and a 5
minute watering run time. You are to enter a program number and a
watering run time for each station. The first numbered key pressed will be
the program number while the next one or t w o numbered keys pressed
will be the run time in minutes. (1 to 99 minutes.) NOTE: No matter what
the watering run time a "0" program number will prevent watering. A "0"
only, can not be entered for a watering run time.
A.
B.
C.
D.
E.
F.
G.
H.
I.
Press Station No. 1 is now displayed.
Press LI one numbered key for the selected program
number
P r e s s
one or two numbered keys for the desired
watering run time for Station No. 1.
Press
Station No. 1 is now entered into
memory.
Press
Station No. 2 is now displayed
Repeat Steps B, C and D for Station No. 2
Press
for Station No. 3
Repeat Steps B, C, D and E for a total of six stations.
Press
to return the display back to the clock.