LAZBOY LZ6200 Installation manual

Manual is about: 10 Function Universal Remote Control With Touchscreen Keypad

Summary of LZ6200

  • Page 1

    Comfort. It's what we do. Touchscreen control model lz6200 10 function universal remote control with touchscreen keypad installation guide tm 95 x 190mm 27 ecp will repair or replace the defective parts and return them at ecp's cost by a shipping method selected by ecp. When contacting ecp to obtain...

  • Page 2

    This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expres...

  • Page 3

    23. -numeric key no.8. 24. -scrolls up thru menus and guides. 25. -numeric key no.9. 26. -brings up the menu screen. 27. -scrolls left thru menus and guides. 28. -allows you to control the input source when in tv mode. 29. -numeric key no.0. 30. -allows access to the ok function when scrolling thru ...

  • Page 4

    5 congratulations on the purchase of your la-z-boy universal remote control, a state of the art product which integrates several infra-red devices to deliver complete a/v control at the tip of your fingers. Before operating your remote please read through this manual carefully and save it for future...

  • Page 5

    7 getting started a few helpful hints on terms used in this manual. Lr: la-z-boy universal remote control led : the blue indicator light that flashes with an infra-red command to your equipment. B a c k l i g h t i n g : t h e b a c k l i g h t i n g o n t h e l c d screen/keypad of your la-z-boy re...

  • Page 6

    9 10 1.1. How to charge batteries when it is first unpacked, the supplied battery pack is not fully charged. Be sure to fully charge it before usage for a minimum of 12 hours. Connect with ac adapter connect the ac adapter to the charging terminal. The red led indicator on the cradle will illuminate...

  • Page 7

    12 11 2. How to set up your la-z-boy remote (lr) 2.1. By entering device code you may setup your la-z-boy remote (lr) by the following code entering instructions. 2.1.1. Turn on your device (e.G. Tv). 2.1.2. Refer to the lr infra red device code list; look up the 4-digit device code which correspond...

  • Page 8

    14 13 2.2.7. Aim the lr at your device (e.G. Tv); press the " " (power) key repeatedly every 1-2 seconds until the device has been turned off. The blue led indicator will blink once each time you press the " " (power) key to indicate your remote is scrolling thru the code library. Once your device h...

  • Page 9

    15 16 3. How to set up your la-z-boy remote (lr) by learning commands your lr is equipped with learning capability. This allows you to "teach" your lr certain functions from your original equipment remote. Please follow the steps below. 3.1. Press the desired device mode key (e.G. Tv). The device na...

  • Page 10

    18 17 4. How to set up your la-z-boy remote (lr) by teaching a dual signal if you found a learned programmed key only works occasionally, your device remote may contain dual signals. Try the following steps to learn this command: 4.1. Follow the steps from 3.1 to 3.4. 4.2. Press a desired key once o...

  • Page 11

    20 19 6. O p e r a t i n g t h e l a - z - b o y remote (lr) normal operation 6.3. The backlit keypad of the lr will turn off if no key is pressed for 8 seconds. 6.4. Your lr controls up to 10 devices. Press each device key directly to select the first 5. Press the " shift " key and then a device ke...

  • Page 12

    21 22 note: - if the same device mode key is pressed twice during the activation process (7.1), the blue led indicator will flash six times , indicating the punch through mode will exit and the punch through status will remain unchanged. - setting channel in punch through mode will activate both the...

  • Page 13

    24 23 9. Program smart keys you can program a sequence of steps into your lr such as turn on your tv, turn on your dvd player, turn on your home theater receiver and press play on your dvd payer to watch a movie. All in sequence. You can also program a time delay in the sequence. Each smart key can ...

  • Page 14

    26 25 12. Troubleshooting q. My lr does not work at all! A. Check your a/v device, if the device's main switch is turned off, your lr can not operate your device. A. Check if your battery pack is connected properly and has been charged for a minimum of 12 hours. For details, please refer to section ...