1. DL manuals
  2. LCN
  3. Door Opening System
  4. Benchmark III 9130
  5. Installation Instructions Manual

LCN Benchmark III 9130 Installation Instructions Manual

Manual is about: automatic electromechanical swinging door operator

Summary of Benchmark III 9130

  • Page 1

    Installation instructions 740158-00 benchmark ® iii swing operator models: 9130, 9140, & 9150 121 west railroad avenue princeton, il 61356-0100 800-526-2400 fax: 800-248-1460 www.Lcn.Ingersollrand.Com 740158-00(1) © 2008 ingersoll-rand company limited.

  • Page 2

    Page 2 of 19 general 2 replacement parts and system components 2 1. Pre-installation site and product check 4 2. Operator installation 5 3. Wiring 9 4. Arm and cover installation 10 5. Operational check 12 6. Operator adjustment 15 7. Release for service 17 8. Benchmark iii software 18 general the b...

  • Page 3

    Page 3 of 19 replacement parts & system components (cntd).

  • Page 4

    Page 4 of 19 1.1 check that the product model is correct for the required application. 1.2 check that all parts listed on the bill of material are in the shipping container. 1.3 check the architectural drawings and final approved shop drawings for the position of frame and structural openings. 1.4 c...

  • Page 5

    Page 5 of 19 2.1 remove control box from operator mounting bracket, then remove motor/gearbox from bracket: 2.2 prepare header/frame and door: 27” pull system ..............................Page 6 full length pull system..................Page 6 27” push system ............................Page 7 full ...

  • Page 6

    Page 6 of 19 27” pull system header/frame and door preparation full length pull system header/frame and door preparation center operator cover (with end caps removed) over opening and mark a vertical line at each end. Align ends of operator mounting bracket and switch bracket with vertical lines and...

  • Page 7

    Page 7 of 19 27” push system header/frame and door preparation full length push system header/frame and door preparation center operator cover (with end caps removed) over opening and mark a vertical line at each end. Align ends of operator mounting bracket and switch bracket with vertical lines and...

  • Page 8

    Page 8 of 19 double push system header/frame and door preparation center operator cover (with end caps removed) over opening and mark a vertical line at each end. Align ends of operator mounting bracket and switch bracket with vertical lines and adjust vertical position per diagram below. Mark and p...

  • Page 9

    Page 9 of 19 tion 3.1 refer to the appropriate wiring diagram for the control box (page 19) or the diagram supplied for custom applications. Connect the following cables: • ground cable (ground the operator properly with the earth from main supply) • hall effect cable (do not wrap the hall effect ca...

  • Page 10

    Page 10 of 19 warning keep hands, clothing, wires, tools, etc., away from operator motor when the operator motor is turned on 4.1 make sure the operator powers is turned off. 4.2 install a jumper across the control box main act and main act. 4.3 turn the operator power switch to on. The operator mot...

  • Page 11

    Page 11 of 19 4.5.2 for pull systems, slide the pull arm roller into the track, then insert a track cap on each end of the track and attach the track to the door: pull arm 4.6 adjust arm: 4.6.1 for pull systems, remove the locking screw from the arm. 4.6.2 for push system, remove the locking screw f...

  • Page 12

    Page 12 of 19 4.9 test the operator. (see chapter 5: operational check on page 13) 4.10 adjust the operator as required. (see chapter 6: operator adjustment on page 15) 4.11 snap the optional end cap insert (in bag of screws) into end cap opposite the on/off switch. 4.12 install the cover assembly o...

  • Page 13

    Page 13 of 19 5.1 set the key switch to auto (if used) and turn on the operator power switch. 5.2 activate the operator using the activation device. The operator will perform one sizing cycle. Sizing cycle: occurs after power is turned on and a legitimate activation signal is received. During the si...

  • Page 14

    Page 14 of 19 5.7.2 door close safety: when the door is in fully open position, activate the safety device and the door should remain open. 5.8 when the door is operating properly, continue with step 4.10 on page 12. 5. Operational check (cntd).

  • Page 15

    Page 15 of 19 see table below and diagrams (page 16) for operator feature adjustment. After adjusting, cycle the door several times to check for proper operation. Then continue with step 4.11 on page 12. Note adjust operator for the slowest operation practical, in accordance with the latest revision...

  • Page 16

    Page 16 of 19 - + less more backcheck position latch position more less + - - + less more open speed time delay more less + - backcheck speed more less + - - + less more close speed off on 4 pb png dly 6. Operator adjustment (cntd).

  • Page 17

    Page 17 of 19 7.1 remove all tools, installation equipment and debris from the vicinity of the door. 7.2 mandatory: install all safety, traffic control and instruction labels onto the door, as required. Failure to do this will leave the installer liable for any accidents that occur. 7.3 give verbal ...

  • Page 18

    Page 18 of 19 8.1 operation: 8.1.1 sizing from start-up (sizing), the door will activate via: • 1-way input (main act and main act). • 2-way input (3-way on, 3-way ho and 3-way gnd) with key switch in the on position, uses either main act or aux act input • key switch in hold open position. The firs...

  • Page 19

    Page 19 of 19 8.3 wiring 8. Benchmark iii software (cntd).