LD WS1000 User Manual - page 5
1
2
3
System Setup
GROUP
GROUP
GROUP
GROUP
CHANNEL
CHANNEL
CHANNEL
CHANNEL
SCAN
SCAN
SCAN
SCAN
FREQ
FREQ
FREQ
FREQ
1
2
3
4
GROUP
CHANNEL
SCAN
FREQ
6
GROUP
CHANNEL
SCAN
FREQ
5
Group and Channel Selection:
Press
“
set
”
button,
“
Group
”
flash, press
or to choose the appreciate frequency group, as shown on the left ;
press
“
SET
”
again ,
“
CHANNEL
”
flashes,press or to choose the
appreciate channel, as
shown on the left shown.
For best results when operating multiple systems, set all
systems to a
single group: then set each system to a unique
channel within that group.
Receiver Volume Setting:
The receiver has electric volume control, as on the normal display, press
or directly to control the output volume
(altogether 64
steps
) as
shown on the left.
We recommend a Set-Up between level 42 to 45.
Normal Display:
RF level,group no,channel no,frequenay as left .
Infrared Frequency Scanning :
Note:
In multiple receivers system,
every receiver's address must be
different!
Turn off the transmitter and open the battery canister (only at bodypack -
handheld has the IR receiver at the bottom of the mic see page 5 point 6)
turn the IR window on the receiver IR window, press
“
ASC
”
button,
and turn on the transmitter again.
Turn the Bodypack receiver IR port on the receiver IP window,then press
“
ASC
”
button, and then press the
“
ASC
”
button on
the bodypack transmitter.
The receiver keeps
transmitting sync frequencies each time you press
the
“
ASC
”
button, and the sign
“
INFRARED
”
flash as shown on the left.
Each time turn on the transmitter and press the
“
ASC
”
button at the
receiver, the reiceiver will start the IR receiving system for 25 seconds.
The handheld transmitter lights up when the IR receiver system starts,
the whole display within the backpack transmitter flashes
(the IR indicator light also flashes at the same time)
Attention:
The
distance of the receiver and the transmitter should be
less than 0.5m as the IR connection is setting; only can turn one
transmitter IR window on the receiver at each IR connection when
multi-system is using.
Auto-Scan Function:
The WS1000 Series has a frequency Auto-Scan Function which makes
it easier to find the next interference free Channel within 1 group.
It may can happen that you still have to find the next interference free
channel manual.
Press “SET” Button 3x until “SCAN” flash. Press or to start the Auto
Scan Run, which may will find the next next interference free Channel
within the selected group.
Battery Status:
The handheld transmitter and the bodypack transmitter had six
levels,as shown on the left.
Group and Channel Display:
After the finishing the connection of the receiver and the transmitter,
the transmitters receiver keeps displaying the numbers of the group
and channel for 5 seconds, as shown on the left, then back to the
normal status display.
Normal Display:
The transmitters shows battery power and working frequency, as
shown on the left.
Receiver Programming
1
1
2
2
3
4
3
6
Transmitter Status Display
5
Handheld
Transmitter
Bodypack
Transmitter
Rack-Mounting the Receiver
7
8
Two TNC connecting cable (included)
Two TNC connector (inlcuded)
One Receiver
(with 19” Rack Ears)
Ten TNC connecting cable (included)
Two TNC connector (included)
Four receivers
WS100DA Antenna Distributor
(optional)
(19” Rack Ears Included)
A
A
B
B
6
5
4
3
2
1
6
5
4
3
2
1
-5
-5
-3
-3
0
0
+3
+3
+6
+6
AF
AF
RF
RF
V
V
SET
IR
GROUP
CHANNEL
SCAN
FREQ
GROUP
CHANNEL
SCAN
FREQ
POWER
- 20
- 20
-10
-10
ASC
ASC
SET
WS 1000 R2
PHONES
PHONES
UHF PLL Diversity
Dual Channel Wireless Receiver
POWER
UHF ANTENNA DISTRIBUTE IMPLEMENT
WS100AD
WS100AD
ANTEN NA-B
ANT -1
ANT -1
ANT -2
ANT -2
ANT -3
ANT -3
ANT -4
ANT -4
ANTEN NA-A
D.C.12-18V IN
200mA
+ -
Maintain a line of sight between
transmitter and antenna.
WS 1000 R2
WS 1000 R2
WS 1000 R2
WS 1000 R2