LDR Astro 200 C LED 5600K Operating Instructions Manual - page 8
Astro
LED
followspot
User’s
Manual
–
1.0
Luci
della
Ribalta
srl,
Via
Berna
14,
46042
Castel
Goffredo
(MN)
Italy
Tel.
+39
0376
771
777
–
fax
+39
0376
772
140
–
info@ldr.it
–
web
www.ldr.it
7
Fig
4:
Control
panel
details
STATUS
:
7
‐
segment,
4
‐
digit
display
for
DMX
address
and
system
setup
and
status
details.
SYSTEM
:
LED
operational
status
indicator.
Normally
off,
flashes
red
if
the
LED
source
is
over
temperature.
SIGNAL
:
Continuous
yellow
=
DMX
OK.
Flashing
yellow
=
invalid
DMX.
Off
=
no
DMX.
POWER
:
Continuous
green
when
power
is
applied.
MANUAL
:
Rotary
intensity
control
if
the
dimming
mode
is
set
to
‘local’
UP/DOWN
:
Buttons
to
step
forward
or
backwards
in
the
menu
or
settings.
ENTER
:
Confirms
selection.
RESET
:
Returns
all
settings
to
factory
default.
12.
LOCAL
CONTROL
PANEL
OPERATION
The
following
operational
features
may
be
set
directly
using
the
rear
control
panel.
12.1
To
set
DMX
dimming
address
1.
On
power
up,
the
default
display
shows
A001
.
Press
ENTER
and
the
display
shows
A.0.0.1.
2.
Use
the
up/down
buttons
to
select
the
intensity
DMX
address.
This
must
be
a
unique
address
and
not
used
for
any
other
functions.
3.
Press
ENTER
and
the
display
will
show
the
new
address.
12.2
To
change
from
DMX
to
local
control
1.
From
the
DMX
address
display;
press
the
down
arrow
to
show
dL01.
Press
ENTER
and
the
display
changes
to
d.L.0.1.
2.
Use
the
up/down
buttons
to
select
2
for
manual
control
or
1
for
DMX
control.
3.
Press
ENTER
and
the
display
will
show
the
selected
mode.
4.
This
feature
can
be
also
overridden
from
the
control
desk
(details
below).
12.3
To
change
LED
temperature
priority
(from
Live
Show
mode
to
longer
life
mode)
The
LED
priority
setting
defaults
to
high
performance
to
maintain
light
levels
for
TV
recordings,
or
specific
scenes
of
a
live
show.
A
temperature
control
feature
is
included
to
lengthen
the
life
of
the
LED
source
by
reducing
intensity
proportionally
as
the
temperature
reaches
a
critical
limit
(greater
than
65°C
/
140°F).
Note
:
switching
the
temperature
priority
ON
can
lengthen
the
LED
life,
but
this
may
result
in
the
light
level
dimming
automatically
in
hot
ambient
conditions.
1.
From
the
DMX
address
display;
press
the
down
arrow
to
show
5L00.
Press
ENTER
and
the
display
changes
to
5.L.0.0.
(i.e.
over
temperature
protection
OFF).
2.
Use
the
up/down
buttons
to
change
to
5.L.0.1.
(i.e.
over
temperature
protection
ON).
3.
Press
ENTER
and
the
display
will
show
the
selected
mode.
4.
This
feature
can
be
also
controlled
from
the
desk
(details
below).