1. DL manuals
  2. Leader
  3. Portable Generator
  4. LT 4600A
  5. Instruction Manual

Leader LT 4600A Instruction Manual

Manual is about: MULTIFORMAT VIDEO GENERATOR

Summary of LT 4600A

  • Page 1

    Lt 4600a multiformat video generator instruction manual (main).

  • Page 2

    Table of contents general safety summary ......................................................................................... I 1. Introduction ........................................................................................................ 1 1.1 scope of warranty .........................

  • Page 3

    5.3 black setting display ............................................................................................................... 23 5.4 sdi setting display.................................................................................................................. 23 6. Lt 4600a config...

  • Page 4

    9.1 selecting the black format ..................................................................................................... 41 9.2 adjusting the timing ................................................................................................................ 43 9.2.1 adjusting the tim...

  • Page 5

    10.8 setting logos ........................................................................................................................... 62 10.8.1 loading a logo................................................................................................................. 62 10.8.2 turning t...

  • Page 6

    14.2 menu tree............................................................................................................................ 89 14.2.1 status menu ................................................................................................................ 89 14.2.2 utility menu ......

  • Page 7

    I general safety summary ■ read this before using the instrument this instrument should only be used by persons with sufficient knowledge of electronics who thoroughly understand the contents of this manual. This instrument is not designed or manufactured for households or ordinary consumers. If unq...

  • Page 8

    Ii general safety summary read the warnings and information below thoroughly to avoid death, personal injury, and damage and deterioration of the instrument. ■ warnings concerning the case and panels do not remove the instrument's case or panels for any reason. Touching the internal components of th...

  • Page 9

    Iii general safety summary ■ warnings concerning the power source do not use a power source with a voltage other than the rated power source voltage for the instrument. Doing so could lead to fire. Confirm the voltage of the power source before you connect the power cord to it. Only use a power sour...

  • Page 10

    Iv general safety summary ■ calibration and repairs this instrument has been carefully examined at the factory to ensure that its performance is in accordance with the standards. However, because of factors such as parts wearing out over time, the performance of the instrument may degrade. To ensure...

  • Page 11

    1. Introduction 1 1. Introduction thank you for purchasing this leader instrument. To use this instrument safely, read this instruction manual thoroughly, and make sure that you know how to use the instrument properly. If some point about the operation of this instrument is still unclear after you h...

  • Page 12

    1. Introduction 2 1.3 operating precautions 1.3.1 power supply voltage confirm the voltage of the power source before you connect the power cord to it. The power requirements of this product are indicated on the rear panel. Only use a power source that supplies a voltage within the operating voltage...

  • Page 13

    1. Introduction 3 name description sd sd-sdi hd hd-sdi hd(dl) hd-sdi dual link 3g-a 3g-sdi level a 3g-b 3g-sdi level b 3g collective term for 3g-a and 3g-b ● logo app logo app is a software for converting bitmap data (*.Bmp) into 4-level monochrome data (*.Lg) that can be used on the lt 4600a. It is...

  • Page 14

    2. Specifications 4 2. Specifications 2.1 general the lt 4600a is a compact, 1u half-rack size sdi video signal generator that supports the triple-rate sdi (3g/hd/sd) format. In addition to test pattern output including color bars and sdi check fields, the lt 4600a is equipped with numerous features...

  • Page 15

    2. Specifications 5 ● analog black output equipped with three independent black signals. The timing can be adjusted by selecting a ntsc/pal black burst signal or a hd tri-level sync signal whose clock frequency is the same as in the sdi output format. Ntsc/pal black burst signal with field reference...

  • Page 16

    2. Specifications 6 2.3 specifications 2.3.1 sdi video output ● sdi electrical characteristics bit rate 3g 2.970 gbps, 2.970/1.001 gbps hd, hd (dl) 1.485 gbps, 1.485/1.001 gbps sd 270 mbps output amplitude 800 mvp-p ± 10% overshoot less than 10% rise and fall times 3g ≤ 135 ps (20 to 80%) hd, hd (dl...

  • Page 17

    2. Specifications 7 ● supported formats 3g-a formats and standards color system quantization image frame (field) frequency/scanning compliant standards ycbcr 4:2:2 10 bits 1920×1080 60/59.94/50/p smpte st 274 smpte st 425 12 bits 1920×1080 60/59.94/50/i 30/29.97/25/24/23.98/p 30/29.97/25/24/23.98/ps...

  • Page 18

    2. Specifications 8 hd (dl) formats and standards color system quantization image frame (field) frequency/scanning compliant standards ycbcr 4:2:2 10 bits 1920×1080 60/59.94/50/p smpte st 274 smpte st 372 12 bits 1920×1080 60/59.94/50/i 30/29.97/25/24/23.98/p 30/29.97/25/24/23.98/psf ycbcr 4:4:4 10 ...

  • Page 19

    2. Specifications 9 ● timing adjustment adjustment range entire frame adjustment unit v lines h clocks (148.5 mhz, 148.5/1.001 mhz, 74.25 mhz, 74.25/1.001 mhz, 27 mhz) ● test patterns 3g, hd 100% color bar, 75% color bar, multiformat color bar (arib std-b28, pattern 2 area can be set to 100% white, ...

  • Page 20

    2. Specifications 10 (can be turned on and off separately) sd action safe area (90%) title safe area (80%) (can be turned on and off separately) * not available when the check field pattern is selected..

  • Page 21

    2. Specifications 11 ● id characters number of characters up to 20 characters size [dots] 32×32, 64×64, 128×128, 256×256 intensity 100%, 75% (black only for the background color) display position anywhere on the display display position adjustment resolution v 1 line h 1 dot blinking display (*1) of...

  • Page 22

    2. Specifications 12 ● channel on/off function each of the y/g, cb/b, and cr/r components can be turned on and off for each channel independently. On outputs the specified y/g, cb/b, or cr/r signal off y/g 040h/000h cb/b 200h/000h cr/r 200h/000h * not available when the check field pattern is select...

  • Page 23

    2. Specifications 13 2.3.2 genlock function external reference input format bnc 75 Ω loop-through compliant standards ntsc black burst signal smpte rp 154, smpte st 170, smpte st 318 pal black burst signal ebu n14, itu-r bt 1700 hd tri-level sync signal smpte st 240, smpte st 274, smpte st 296 sync ...

  • Page 24

    2. Specifications 14 2.3.4 word-clock output output frequency 48 khz output amplitude 5v cmos compatible (when not terminated) output connector bnc outputs 1 timing adjustment adjustment range ±1 aes/ebu frame adjustment unit 512 fs (24.576 mhz) 2.3.5 aes/ebu digital audio output compliant standards...

  • Page 25

    2. Specifications 15 2.3.7 presets presets saves the panel settings (*1) number of presets 10 recall method front panel copy method copy all presets from the lt 4600a to a usb memory device or copy all presets from the usb memory device to the lt 4600a * last memory is not supported. By setting powe...

  • Page 26

    3. Panel description 16 3. Panel description 3.1 front panel no. Name description 1 lcd shows various information. 2 menu switches the menu. See section 4.5, “menu operations.” 3 function enables and disables the key lock. See section 6.2, “turning key lock on and off.” 4 alarm blinks when the fan s...

  • Page 27

    3. Panel description 17 3.2 rear panel no. Name description 1 genlock in genlock input connectors. They are loop-through connectors. They receive hd tri-level sync or ntsc/pal black burst signals. See chapter 7, “genlock function (reference setting.)” 2 black out black output connectors. They output...

  • Page 28

    4. Before use 18 4. Before use 4.1 attaching the cover inlet stopper a cover/inlet stopper is included with the lv 7390. Use this device to prevent the power cord from being pulled free of the ac inlet. To attach the cover/inlet stopper, follow the procedure below. ● attaching the cover/inlet stoppe...

  • Page 29

    4. Before use 19 4.2 turning the power on ● turning the power on the lt 4600a does not have a power switch. Simply connect the power cord. ● starting when the power turns on, the lt 4600a starts to initialize. During initialization, signals are not output, and you cannot use the keys. ● startup comp...

  • Page 30

    4. Before use 20 4.4 connecting a usb memory device to import and export various data, you can use a usb memory device. Use a usb memory device whose capacity is 8 gb or less. You can connect and disconnect a usb memory device with the power turned on. When you connect a usb memory device, the follo...

  • Page 31

    4. Before use 21 ● menu levels with the exception of a portion of the screens, the settings menus show a number to the upper left of the screen. This number indicates the menu level. The larger the number, the deeper the level. To enter a lower level menu, press enter. (in some screens, you can also...

  • Page 32

    5. Status display (status) 22 5. Status display (status) the status display shows the genlock status and the current main settings. This screen is only for viewing; you cannot change the settings. To switch screens, use the and keys. 5.1 genlock status display lt 4600a lock status displays the genlo...

  • Page 33

    5. Status display (status) 23 5.2 genlock setting display genlock st displays the genlock mode selected in section 7.2, “selecting the genlock mode.” ［ＳＴＡＴＵＳ］ ＧＥＮＬＯＣＫ ＳＴ  ＩＮＴＥＲＮＡＬ 5.3 black setting display black 1, black 2, and black 3 display the black format selected in section 9.1, “selecting th...

  • Page 34

    6. Lt 4600a configuration (utility setting) 24 6. Lt 4600a configuration (utility setting) utility setting is used to configure the basic lt 4600a settings. These settings are not stored to presets. 6.1 turning the backlight on and off to turn the lcd backlight on or off, follow the procedure below....

  • Page 35

    6. Lt 4600a configuration (utility setting) 25 6.3 configuring presets presets contain lt 4600a settings that you registered. Presets can be imported and exported through a usb memory device. A preset can be recalled automatically at startup. 6.3.1 saving presets you can save up to 10 presets by fol...

  • Page 36

    6. Lt 4600a configuration (utility setting) 26 6.3.4 exporting the presets to export the presets from the lt 4600a to a usb memory device, follow the procedure below. This feature is useful when you want to use multiple lt 4600as with the same settings. All 10 presets are exported to a single file. ...

  • Page 37

    6. Lt 4600a configuration (utility setting) 27 6.4 setting logos the logos (.Lg format) that you create with the supplied logo application can be imported into the lt 4600a and overlaid on sdi signals. Up to four logos can be imported. Imported logos are retained even if the lt 4600a is restarted or...

  • Page 38

    6. Lt 4600a configuration (utility setting) 28 6.4.3 exporting a logo to export a logo selected in section 6.4.1, “selecting a logo,” to a usb memory device, follow the procedure below. While the presets are being exported, an indicator appears to show the progress. When the original screen returns,...

  • Page 39

    6. Lt 4600a configuration (utility setting) 29 6.5 configuring ethernet settings 6.5.1 setting the ip address to set the ip address, subnet mask, and default gateway, follow the procedure below. For the new ip address to take effect, you need to restart the lt 4600a. When you restart the lt 4600a, s...

  • Page 40

    6. Lt 4600a configuration (utility setting) 30 6.5.4 setting the trap transmission destination to set the ip address of the snmp manager to send snmp traps to, follow the procedure below. ３．ＭＡＮＡＧＥＲ ＩＰ １９２．１６８．０００．０００ procedure utility setting → ethernet → snmp trap → manager ip 6.5.5 setting the com...

  • Page 41

    6. Lt 4600a configuration (utility setting) 31 6.5.6 retrieving the mib file to copy the mib file, which is used for snmp, from the lt 4600a to a usb memory device, follow the procedure below. ２．ＧＥＴ ＭＩＢ ＦＩＬＥ ■ＯＫ □ＣＡＮＣＥＬ procedure utility setting → ethernet → get mib file ● usb memory device file str...

  • Page 42

    6. Lt 4600a configuration (utility setting) 32 6.6 setting the date and time to set the date and time, follow the procedure below. The date and time are used in data exporting, genlock log, and so on. The date and time are reset to their factory default values (2012/01/01 00:00:00) each time the lt ...

  • Page 43

    7. Genlock function (reference setting) 33 7. Genlock function (reference setting) 7.1 genlock function this chapter will explain how to use the lt 4600a for the following two lock modes. Lock mode reference signal description internal mode internal the internal reference signal is used. The factory...

  • Page 44

    7. Genlock function (reference setting) 34 7.1.2 genlock mode 1. Under reference setting, set genlock mode to stay-in-sync. Reference section 7.2, “selecting the genlock mode” 2. Under reference setting, select lock format. Select the reference signal format. Reference section 7.3, “selecting the ge...

  • Page 45

    7. Genlock function (reference setting) 35 ● panel display when you apply a reference signal, tracking fast appears under lt4600a lock status, and ext under ref blinks in green. This indicates that the reference signal is being drawn in. When genlock is complete, external appears under lt4600a lock ...

  • Page 46

    7. Genlock function (reference setting) 36 7.2 selecting the genlock mode to select the genlock mode, follow the procedure below. If you select stay-in-sync when the mode is already in stay-in-sync mode, a message “re-adjust ok?” will appear. This is used to relock when stay-in-sync operation is in ...

  • Page 47

    7. Genlock function (reference setting) 37 7.4 adjusting the timing (fine adjustment) when the lt 4600a is locked in genlock mode, to finely adjust the black signal relative to the reference signal, follow the procedure below. The procedure here adjusts the timing of black signals 1 to 3 simultaneou...

  • Page 48

    7. Genlock function (reference setting) 38 7.5.3 saving the log to save the genlock log in log format to a usb memory device, follow the procedure below. The content of a file in log format can be viewed using wordpad and other text editors. １．ＧＥＮＬＯＣＫ ＬＯＧ ＳＡＶＥ ■ＯＫ □ＣＡＮＣＥＬ procedure reference setting...

  • Page 49

    8. Configuring the system (system setting) 39 8. Configuring the system (system setting) system setting is used to configure the lt 4600a operation. Note that if you change the system settings, the settings specified using black setting and sdi setting are reset to their factory defaults. 8.1 select...

  • Page 50

    8. Configuring the system (system setting) 40 8.3 selecting the sdi output signal to select the sdi output mode, follow the procedure below. ２．ＳＤＩ １  ＊３Ｇ－ＳＤＩ－ＬｖＡ ＯＵＴＰＵＴ ＣＨＡＮＧＥ ？ ■ＯＫ □ＣＡＮＣＥＬ ２．ＳＤＩ ２  ＊３Ｇ－ＳＤＩ－ＬｖＡ ＯＵＴＰＵＴ ＣＨＡＮＧＥ ？ ■ＯＫ □ＣＡＮＣＥＬ ２．３Ｇ－ＬｖＢ／ＤＵＡＬ ＬＩＮＫ  ＊３Ｇ－ＳＤＩ－ＬｖＢ ＯＵＴＰＵＴ ＣＨＡＮＧＥ ？ ■ＯＫ □ＣＡＮＣＥ...

  • Page 51

    9. Analog black output (black setting) 41 9. Analog black output (black setting) three analog black signals are output from the black out connectors on the rear panel. You can set the output signals using black setting. Specify the settings under black setting after you have finished configuring the...

  • Page 52

    9. Analog black output (black setting) 42 blk* format system select 60.00hz group 59.94hz group 50.00hz group 720p/30 yes no no 720p/29.97 no yes no 720p/25 no no yes 720p/24 yes no no 720p/23.98 no yes no ntsc bb fd fd fd ntsc bb+ref yes yes yes ntsc bb+id yes yes yes ntsc bb+ref+id yes yes yes nts...

  • Page 53

    9. Analog black output (black setting) 43 9.2 adjusting the timing note that if you change the black format, the timing adjustment specified here is reset to its factory default. Reference section 9.1, “selecting the black format” 9.2.1 adjusting the timing (frame) to adjust the black signal relativ...

  • Page 54

    9. Analog black output (black setting) 44 9.2.3 adjusting the timing (dot) to adjust the black signal relative to the reference signal at the dot level, follow the procedure below. (the adjustment range provided below is the maximum. The range depends on the format.) you can also adjust at the time ...

  • Page 55

    10. Sdi output (sdi setting) 45 10. Sdi output (sdi setting) two sdi signals are output from the sdi out connectors on the rear panel. You can set the output signals using sdi setting. Specify the settings under sdi setting after you have finished configuring the system settings. Note that if you ch...

  • Page 56

    10. Sdi output (sdi setting) 46 the selectable format and color system combinations are shown below. Formats not listed cannot be selected. In addition, the formats that you can select vary depending on the frequency group that you selected in section 8.1 “selecting the frequency group.” ● 3g-a outp...

  • Page 57

    10. Sdi output (sdi setting) 47 ● 3g-b output format color system system select 422(ycbcr) 10 bits 422(ycbcr) 12 bits 444(ycbcr) 10 bits 444(ycbcr) 12 bits 444(rgb) 10 bits 444(rgb) 12 bits 1080i/60 no yes yes yes yes yes 60.00hz 1080i/59.94 no yes yes yes yes yes 59.94hz 1080i/50 no yes yes yes yes...

  • Page 58

    10. Sdi output (sdi setting) 48 ● hd/sd output format color system system select 422(ycbcr) 10 bits 422(ycbcr) 12 bits 444(ycbcr) 10 bits 444(ycbcr) 12 bits 444(rgb) 10 bits 444(rgb) 12 bits 1080i/60 yes no no no no no 60.00hz 1080i/59.94 fd no no no no no 59.94hz 1080i/50 yes no no no no no 50.00hz...

  • Page 59

    10. Sdi output (sdi setting) 49 the selectable patterns depend on the output format as shown below. Pattern format 3g/hd(dl)/hd 525i/59.94 625i/50 color bar 100% yes yes yes color bar 75% yes yes no multi cb 100% yes no no multi cb 75% yes no no multi cb (+i) yes no no smpte color bar no yes no ebu ...

  • Page 60

    10. Sdi output (sdi setting) 50 smpte color bar ebu color bar bbc color bar check field blue field 100% green filed 100% red field 100%.

  • Page 61

    10. Sdi output (sdi setting) 51 flat field 0% flat field 100% 10.2.2 turning pattern scrolling on and off to turn pattern scrolling on and off, follow the procedure shown below. If the check field pattern is selected, the patter will not scroll even if this is set to on. ４．ＳＣＲＯＬＬ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ pro...

  • Page 62

    10. Sdi output (sdi setting) 52 10.2.4 setting the pattern scroll speed to select the pattern scroll speed, follow the procedure below. The unit is dot/field (frame). If the speed is set to 0, the pattern will not scroll. The value takes effect immediately. Pressing cancel does not revert the settin...

  • Page 63

    10. Sdi output (sdi setting) 53 10.3 adjusting the timing note that if you change the sdi format, the timing adjustment specified here is reset to its factory default. Reference section 10.1, “selecting the sdi format” 10.3.1 selecting the timing reference to select the output timing used as a refer...

  • Page 64

    10. Sdi output (sdi setting) 54 10.3.4 adjusting the timing (time) to adjust the sdi signal relative to the reference signal at the time level, follow the procedure below. (the adjustment range provided below is the maximum. The range depends on the format.) you can also adjust at the dot level inst...

  • Page 65

    10. Sdi output (sdi setting) 55 10.4.1 settings shared by links if the output signal is 3g-b, the link b settings can be linked to link a settings by following the procedure below to select on. It is possible to set the link b settings even when this is set to on, but the values will be ignored. ４．Ｅ...

  • Page 66

    10. Sdi output (sdi setting) 56 10.4.4 turning the audio on and off to turn the audio on or off at the group level, follow the procedure below. ４．ＡＵＤＩＯ ＯＮ／ＯＦＦ ＊■Ｇ１ ■Ｇ２ ■Ｇ３ ■Ｇ４ procedure sdi setting → sdi → embedded audio → audio on/off: on / off 10.4.5 selecting the resolution to select the resoluti...

  • Page 67

    10. Sdi output (sdi setting) 57 10.4.8 setting the level to set the level of the selected channel, follow the procedure below. ７．ＬＥＶＥＬ －２０ ｄＢＦＳ procedure sdi setting → sdi → embedded audio → group * set → ch select → group * ch* → level: -60 - -20 - 0 10.4.9 setting clicks you can insert click sound...

  • Page 68

    10. Sdi output (sdi setting) 58 90% area = on / 4:3 area = off 90% area = on / 4:3 area = on 10.6.2 turning the 80% marker on and off to turn the 80% marker on and off, follow the procedure below. If the 4:3 marker is off, the 80% marker is displayed at the outer frame of the picture. If the 4:3 mar...

  • Page 69

    10. Sdi output (sdi setting) 59 10.7 setting id characters 10.7.1 turning id characters on and off to turn id characters on and off, follow the procedure below. If the check field pattern is selected, the id characters will not be displayed even if this is set to on. ３．ＩＤ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ procedure s...

  • Page 70

    10. Sdi output (sdi setting) 60 10.7.3 setting the position of id characters to set the position of the id characters, follow the procedure below. The values represent the coordinates at the upper left corner of the id characters. The upper left corner of the pattern is 0. The value takes effect imm...

  • Page 71

    10. Sdi output (sdi setting) 61 10.7.7 setting the id character blinking time to set the id character blinking time, follow the procedure below. ４．ＩＤ ＢＬＩＮＫ ＯＮ ＴＩＭＥ ＋１ ｓｅｃ ４．ＩＤ ＢＬＩＮＫ ＯＦＦ ＴＩＭＥ ＋１ ｓｅｃ procedure sdi setting → sdi → id character → id blink → id blink on time: +1 - +9 (on-time) → id blink...

  • Page 72

    10. Sdi output (sdi setting) 62 10.8 setting logos the logos (.Lg format) that you create with the supplied logo application can be imported into the lt 4600a and overlaid on sdi signals. 10.8.1 loading a logo to display a logo, you need to load it first. You can either load a logo that has been imp...

  • Page 73

    10. Sdi output (sdi setting) 63 10.8.3 setting the logo position to set the logo position, follow the procedure below. The values represent the coordinates at the upper left corner of logo. The upper left corner of the pattern is 0. The value takes effect immediately. Pressing cancel does not revert...

  • Page 74

    10. Sdi output (sdi setting) 64 10.8.5 selecting the logo background to select whether to make the area set to level 0 transparent, follow the procedure below. ３．ＬＯＧＯ ＢＡＣＫＧＲＯＵＮＤ □ＯＮ ■ＯＦＦ procedure sdi setting → sdi → logo → logo background: on / off logo background = on logo background = off.

  • Page 75

    10. Sdi output (sdi setting) 65 10.9 configuring lip sync combining the lt 4600a and our waveform monitor lv 5770(a) makes it possible to measure the offset between the video signal and the audio signal that occurs in the transfer route for each channel. Prepare an lv 5770(a) with an lv 5770ser08/09...

  • Page 76

    10. Sdi output (sdi setting) 66 10.9.2 description of lip sync patterns a lip sync pattern is divided into three areas. From the top, they are the pattern, raster, and scale areas. Audio is turned on or muted in sync with the image signal. ● pattern the pattern specified by pattern is displayed. Mar...

  • Page 77

    11. Aes/ebu digital audio output (aes/ebu setting) 67 11. Aes/ebu digital audio output (aes/ebu setting) two 48 khz aes/ebu signals synchronized with video signals are output from the aes/ebu connectors on the rear panel. You can set the output signal using aes/ebu setting. In aes/ebu setting, you c...

  • Page 78

    11. Aes/ebu digital audio output (aes/ebu setting) 68 11.4 selecting the pre-emphasis mode to select the pre-emphasis mode, follow the procedure below. ２．ＥＭＰＨＡＳＩＳ □５０／１５ □ＣＣＩＴＴ ■ＯＦＦ procedure aes/ebu setting →aes/ebu 1 → emphasis: 50/15 / ccitt / off 11.5 settings shared by channels you can link the...

  • Page 79

    11. Aes/ebu digital audio output (aes/ebu setting) 69 11.8 setting clicks you can insert click sounds into the selected channel. Follow the procedure below to set the insertion interval in the range of 1 sec to 4 sec. This setting is valid when lipsync enable is set to disable. ４．ＣＬＩＣＫ  ＊ＯＦＦ ↵ proc...

  • Page 80

    12. Word-clock output (wclk setting) 70 12. Word-clock output (wclk setting) a 48 khz word-clock signal synchronized to the video signal is output from the wclk out connector on the rear panel. You can set the output signal using wclk setting. 12.1 adjusting the timing to adjust the word-clock signa...

  • Page 81

    13. Snmp 71 13. Snmp by using snmp (simple network management protocol), you can check the lt 4600a status from an snmp manager. In addition, when the fan stops or other errors occur, traps can be sent from the lt 4600a to an snmp manager. * the ethernet features of the lt 4600a have only been confi...

  • Page 82

    13. Snmp 72 4. On the snmp manager, set the ip address of the trap transmission destination. Oid: 1.3.6.1.4.1.Leader(20111).Lt4600(28).Trap(100).Target(1).Managerip(1).0 you can also set it from the lt 4600a menu. 5. On the snmp manager, set trap transmission to enable(1). Oid: 1.3.6.1.4.1.Leader(20...

  • Page 83

    13. Snmp 73 ro: read only. R/w: read and write..

  • Page 84

    13. Snmp 74 13.4.1 status group ● fanunit(1) group mib oid syntax access value description fanstatus fanunit.1 integer ro 2 stop 3 operation ● genlocksts(2) group mib oid syntax access value description genstatus genlocksts.1 integer ro 1 disable 2 internal 3 unlock 4 locked 5 stay-in-sync 13.4.2 re...

  • Page 85

    13. Snmp 75 mib oid syntax access value description 64 625p/50 13.4.3 analogblack group ● output1(1) group mib oid syntax access value description blk1format output1.1 integer ro 1 1080i/60 2 1080i/59.94 3 1080i/50 4 1080p/30 5 1080p/29.97 6 1080p/25 7 1080p/24 8 1080p/23.98 15 1080psf/24 16 1080psf...

  • Page 86

    13. Snmp 76 ● output2(2) group mib oid syntax access value description blk2format output2.1 integer ro same as output1(1) group ● output3(3) group mib oid syntax access value description blk3format output3.1 integer ro same as output1(1) group 13.4.4 serialdigital group ● sdi1(1) group mib oid synta...

  • Page 87

    13. Snmp 77 mib oid syntax access value description 2026 3g-a 444(ycbcr) 10 bit 720p/25 2027 3g-a 444(ycbcr) 10 bit 720p/24 2028 3g-a 444(ycbcr) 10 bit 720p/23.98 3001 3g-a 444(ycbcr) 12 bit 1080i/60 3002 3g-a 444(ycbcr) 12 bit 1080i/59.94 3003 3g-a 444(ycbcr) 12 bit 1080i/50 3007 3g-a 444(ycbcr) 12...

  • Page 88

    13. Snmp 78 mib oid syntax access value description 10009 hd 422(ycbcr) 10 bit 1080p/25 10010 hd 422(ycbcr) 10 bit 1080p/24 10011 hd 422(ycbcr) 10 bit 1080p/23.98 10015 hd 422(ycbcr) 10 bit 1080psf/24 10016 hd 422(ycbcr) 10 bit 1080psf/23.98 10021 hd 422(ycbcr) 10 bit 720p/60 10022 hd 422(ycbcr) 10 ...

  • Page 89

    13. Snmp 79 mib oid syntax access value description 23002 3g-b 444(ycbcr) 12 bit 1080i/59.94 23003 3g-b 444(ycbcr) 12 bit 1080i/50 23007 3g-b 444(ycbcr) 12 bit 1080p/30 23008 3g-b 444(ycbcr) 12 bit 1080p/29.97 23009 3g-b 444(ycbcr) 12 bit 1080p/25 23010 3g-b 444(ycbcr) 12 bit 1080p/24 23011 3g-b 444...

  • Page 90

    13. Snmp 80 mib oid syntax access value description 32002 hd(dl) 444(ycbcr) 10 bit 1080i/59.94 32003 hd(dl) 444(ycbcr) 10 bit 1080i/50 32007 hd(dl) 444(ycbcr) 10 bit 1080p/30 32008 hd(dl) 444(ycbcr) 10 bit 1080p/29.97 32009 hd(dl) 444(ycbcr) 10 bit 1080p/25 32010 hd(dl) 444(ycbcr) 10 bit 1080p/24 32...

  • Page 91

    13. Snmp 81 mib oid syntax access value description 35011 hd(dl) 444(rgb) 12 bit 1080p/23.98 35012 hd(dl) 444(rgb) 12 bit 1080psf/30 35013 hd(dl) 444(rgb) 12 bit 1080psf/29.97 35014 hd(dl) 444(rgb) 12 bit 1080psf/25 35015 hd(dl) 444(rgb) 12 bit 1080psf/24 35016 hd(dl) 444(rgb) 12 bit 1080psf/23.98 s...

  • Page 92

    13. Snmp 82 mib oid syntax access value description 9 g1: on g2: off g3: off g4: off 10 g1: on g2: off g3: off g4: on 11 g1: on g2: off g3: on g4: off 12 g1: on g2: off g3: on g4: on 13 g1: on g2: on g3: off g4: off 14 g1: on g2: on g3: off g4: on 15 g1: on g2: on g3: on g4: off 16 g1: on g2: on g3:...

  • Page 93

    13. Snmp 83 13.4.5 trap group ● target(1) group mib oid syntax access value description managerip target.1 ip address r/w *.*.*.* trap transmission destination trapaction target.2 integer r/w 1 enable 2 disable 13.5 extended trap id event name description object data 1 fanunitstatus fan unit status ...

  • Page 94

    14. Appendix 84 14. Appendix 14.1 list of settings a list of settings that you can specify on the lt 4600a is provided below. The description of each item is as follows: presets y items that are saved to presets n items that are not saved to presets last memory y at startup, settings that are set to...

  • Page 95

    14. Appendix 85 14.1.2 reference setting setting value (maximum) factory default value preset last memory genlock mode internal / stay-in-sync internal y m lock format 1125i/60 / 1125i/59.94 / 1125i/50 / 1125p/30 / 1125p/29.97 / 1125p/25 / 1125p/24 / 1125p/23.98 / 1125psf/24 / 1125psf/23.98 / 750p/6...

  • Page 96

    14. Appendix 86 14.1.4 black setting setting value (maximum) factory default value preset last memory blk1 format 1080i/60 / 1080i/59.94 / 1080i/50 / 1080p/30 / 1080p/29.97 / 1080p/25 / 1080p/24 / 1080p/23.98 / 1080psf/24 / 1080psf/23.98 / 720p/60 / 720p/59.94 / 720p/50 / 720p/30 / 720p/29.97 / 720p...

  • Page 97

    14. Appendix 87 setting value (maximum) factory default value preset last memory down & right / right h speed 0 - +256 0 y m v speed 0 - +256 0 y m scroll on/off on / off off y m speed +1 - +255 +1 y m change on/off on / off off y m 0h timing serial / legacy legacy y m v-phase ±1124 0 y m h-phase [d...

  • Page 98

    14. Appendix 88 setting value (maximum) factory default value preset last memory logo h-position 0 - +1919 0 y m level 3 100h - eb0h eb0h y m level 2 100h - eb0h a20h y m level 1 100h - eb0h 590h y m level 0 100h - eb0h 100h y m logo background on / off off y m logo on/off on / off off y m lipsync o...

  • Page 99

    14. Appendix 89 14.2 menu tree the screen shows the initial settings. 14.2.1 status menu ＬＴ４６００Ａ ＬＯＣＫ ＳＴＡＴＵＳ ［ ＩＮＴＥＲＮＡＬ ］ ［ＳＴＡＴＵＳ］ ＧＥＮＬＯＣＫ ＳＴ ＩＮＴＥＲＮＡＬ ［ＳＴＡＴＵＳ］ ＳＤＩ２ ＳＡＭＰＬＥ ４２２（ＹＣｂＣｒ） １０ｂｉｔ ［ＳＴＡＴＵＳ］ ＳＤＩ２ ＰＡＴＴ ＣＯＬＯＲ ＢＡＲ １００％ ［ＳＴＡＴＵＳ］ ＳＤＩ２ ＦＯＲＭＡＴ １０８０ｉ／５９．９４ ［ＳＴＡＴＵＳ］ ＢＬＡＣＫ ３ ＮＴＳＣ ＢＢ ［ＳＴＡＴＵＳ］ ＯＵＴＰＵＴ ＭＯＤ...

  • Page 100

    14. Appendix 90 14.2.2 utility menu ２．ＳＮＭＰ ＴＲＡＰ ＭＡＮＡＧＥＲ ＩＰ ↵ ２．ＳＮＭＰ ＴＲＡＰ ＡＣＴＩＯＮ ↵ ＦＯＲＭＡＴ ＆ ＲＥＢＯＯＴ ＯＫ ？ □ＯＫ ■ＣＡＮＣＥＬ ２．ＧＥＴ ＭＩＢ ＦＩＬＥ □ＯＫ ■ＣＡＮＣＥＬ ＯＶＥＲ ＷＲＩＴＥ ＯＫ ？ □ＯＫ ■ＣＡＮＣＥＬ ２．ＳＮＭＰ ＣＯＭＭＵＮＩＴＹ ＲＥＡＤ ＣＯＭＭＵＮＩＴＹ ↵ ３．ＲＥＡＤ ＣＯＭＭＵＮＩＴＹ Ｌ ＤＲＵｓｅｒ ２．ＭＡＣ ＡＤＤＲＥＳＳ ＊＊：＊＊：＊＊：＊＊：＊＊：＊＊ ３．ＡＣＴＩＯＮ □ＥＮＡＢＬＥ ■ＤＩＳＡＢＬＥ １．ＦＡＣＴＯＲＹ ＤＥ...

  • Page 101

    14. Appendix 91 ＦＯＲＭＡＴ ＆ ＲＥＢＯＯＴ ＯＫ ？ □ＯＫ ■ＣＡＮＣＥＬ ２．ＳＵＢＮＥＴ ＭＡＳＫ ２５ ５ ．２５５．２５５．０００ ２．ＩＰ ＡＤＤＲＥＳＳ １９ ２ ．１６８．０００．０００ ２．ＧＥＴ ＭＩＢ ＦＩＬＥ □ＯＫ ■ＣＡＮＣＥＬ ＯＶＥＲ ＷＲＩＴＥ ＯＫ ？ □ＯＫ ■ＣＡＮＣＥＬ １．ＤＡＴＥ ＆ ＴＩＭＥ ＡＤＪＵＳＴ ２０１ ２ ／０１／０１ ００：００：００ １．ＶＥＲＳＩＯＮ ＤＩＳＰ（ＭＡＩＮ） ＢＯＯＴ：ｖｅｒ０１．００－００００ １．ＶＥＲＳＩＯＮ ＤＩＳＰ（ＭＡＩＮ） ＳＹＳ ：ｖｅｒ０１．００－００００ ０．ＵＴＩＬＩＴＹ ...

  • Page 102

    14. Appendix 92 14.2.3 reference menu ０．ＲＥＦＥＲＥＮＣＥ ＳＥＴＴＩＮＧ ＧＥＮＬＯＣＫ ＬＯＧ ＯＮ／ＯＦＦ ↵ １．ＧＥＮＬＯＣＫ ＬＯＧ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ ０．ＲＥＦＥＲＥＮＣＥ ＳＥＴＴＩＮＧ ＧＥＮＬＯＣＫ ＬＯＧ ＳＡＶＥ ↵ １．ＧＥＮＬＯＣＫ ＬＯＧ ＳＡＶＥ □ＯＫ ■ＣＡＮＣＥＬ ０．ＲＥＦＥＲＥＮＣＥ ＳＥＴＴＩＮＧ ＧＥＮＬＯＣＫ ＬＯＧ ＤＩＳＰ ↵ １．ＧＥＮＬＯＣＫ ＬＯＧ ＤＩＳＰ ００：２０１２／０１／０１ ００：３８ ＣＨＡＮＧＥ ＧＬ ＭＯＤＥ ？ □ＯＫ ■ＣＡＮＣＥＬ １．ＧＥＮＬＯＣＫ ＭＯＤＥ...

  • Page 103

    14. Appendix 93 14.2.4 system menu ＯＵＴＰＵＴ ＣＨＡＮＧＥ ？ □ＯＫ ■ＣＡＮＣＥＬ ＯＵＴＰＵＴ ＣＨＡＮＧＥ ？ □ＯＫ ■ＣＡＮＣＥＬ ２．ＳＤＩ １ ＊ＨＤ／ＳＤ－ＳＤＩ ( 3g-sdi-lva / hd/sd-sdi ) １．ＳＤＩ ＯＵＴＰＵＴ ＳＥＬＥＣＴ ＳＤＩ ２ ↵ ０．ＳＹＳＴＥＭ ＳＥＴＴＩＮＧ ＳＤＩ ＯＵＴＰＵＴ ＳＥＬＥＣＴ １．ＳＤＩ ＯＵＴＰＵＴ ＳＥＬＥＣＴ ＭＯＤＥ ＳＥＬＥＣＴ ↵ ２．ＭＯＤＥ ＳＥＬＥＣＴ ＊ＳＤＩ １ ／ ２ ＣＨＡＮＧＥ ＳＹＳＴＥＭ ？ □ＯＫ ■ＣＡＮＣＥＬ １．ＳＹＳＴＥＭ ＳＥＬＥ...

  • Page 104

    14. Appendix 94 14.2.5 black menu ( ± 5 ) ２．ＢＬＫ１ ＴＩＭＩＮＧ ＢＬＫ１ Ｈ－ＰＨＡＳＥ［μｓ］ ↵ ０．ＢＬＡＣＫ ＳＥＴＴＩＮＧ ＢＬＡＣＫ１ ＳＩＧＮＡＬ ２．ＢＬＫ１ ＴＩＭＩＮＧ ＢＬＫ１ Ｈ－ＰＨＡＳＥ［ｄｏｔ］ ↵ ３．ＢＬＫ１ Ｖ－ＰＨＡＳＥ ０ ｌｉｎｅ ２．ＢＬＫ１ ＴＩＭＩＮＧ ＢＬＫ１ Ｖ－ＰＨＡＳＥ ↵ ( ± 1 1 2 4 ) ( ± 4 1 2 4 ) ３．ＢＬＫ１ Ｈ－ＰＨＡＳＥ［μｓ］ ＋０．００００ μｓ n t s c * 、 5 2 5 i / 5 9 . 9 4 、 p a l * 、 6 2 5 i ...

  • Page 105

    14. Appendix 95 14.2.6 sdi menu ３．Ｖ－ＰＨＡＳＥ ０ ｌｉｎｅ ( ± 1 1 2 4 ) ( ± 8 2 4 9 ) ３．Ｈ－ＰＨＡＳＥ ［μｓ］ ＋０．００００ μｓｅｃ ３．Ｈ－ＰＨＡＳＥ ［ｄｏｔ］ ０ ｄｏｔ ２．ＴＩＭＩＮＧ Ｈ－ＰＨＡＳＥ ［μｓ］ ↵ ２．ＴＩＭＩＮＧ Ｈ－ＰＨＡＳＥ ［ｄｏｔ］ ↵ ２．ＦＯＲＭＡＴ ＊１０８０ｉ／５９．９４ ( ± 6 3 . 9 6 2 9 ) h d ( d l ) 、 h d 、 s d の と き ２．ＴＩＭＩＮＧ Ｖ－ＰＨＡＳＥ ↵ １．ＳＤＩ １（３Ｇ－ＳＤＩ－ＬｖＡ） ＦＯＲＭＡＴ ↵ ０．ＳＤ...

  • Page 106

    14. Appendix 96 ch2と 同 様 ( -60 - 0 ) ６．ＧＲＯＵＰ１ ＣＨ２ ＣＬＩＣＫ ↵ ７．ＣＬＩＣＫ ＊ＯＦＦ ↵ ( off / 1sec / 2sec / 3sec / 4sec ) ch2と 同 様 ４．ＧＲＯＵＰ １ ＳＥＴ ＥＭＰＨＡＳＩＳ ↵ ４．ＡＵＤＩＯ ＯＮ／ＯＦＦ ＊■Ｇ１ ■Ｇ２ ■Ｇ３ ■Ｇ４ ３．ＬＩＮＫ－Ｂ ＥＱＵＡＬ ＴＯ ＬＩＮＫ－Ａ ↵ ２．ＥＭＢＥＤＤＥＤ ＡＵＤＩＯ ＬＩＮＫ－Ａ ３．ＬＩＮＫ－Ａ ＡＵＤＩＯ ＯＮ／ＯＦＦ ↵ ４．ＥＱＵＡＬ ＴＯ ＬＩＮＫ－Ａ □ＯＮ ■ＯＦＦ ３．ＬＩＮＫ－Ａ ＧＲＯＵＰ １ ＳＥＴ １．...

  • Page 107

    14. Appendix 97 group 1と 同 様 group 1と 同 様 ５．ＥＱＵＡＬ ＴＯ Ｇ３ □ＯＮ ■ＯＦＦ ４．ＧＲＯＵＰ ４ ＳＥＴ ＲＥＳＯＬＵＴＩＯＮ ↵ ４．ＧＲＯＵＰ ２ ＳＥＴ ＲＥＳＯＬＵＴＩＯＮ ↵ ５．ＲＥＳＯＬＵＴＩＯＮ ■２０ｂｉｔ □２４ｂｉｔ ５．ＥＱＵＡＬ ＴＯ Ｇ１ □ＯＮ ■ＯＦＦ ５．ＲＥＳＯＬＵＴＩＯＮ ■２０ｂｉｔ □２４ｂｉｔ ３．ＬＩＮＫ－Ａ ＧＲＯＵＰ ３ ＳＥＴ group 1と 同 様 ３．ＬＩＮＫ－Ａ ＧＲＯＵＰ ４ ＳＥＴ ４．ＧＲＯＵＰ ４ ＳＥＴ ＥＱＵＡＬ ＴＯ Ｇ３ ↵ ３．ＬＩＮＫ－Ａ ＧＲＯＵＰ ２ ＳＥＴ ...

  • Page 108

    14. Appendix 98 ２．ＩＤ ＣＨＡＲＡＣＴＥＲ ＩＤ ＯＮ／ＯＦＦ ↵ ３．ＩＤ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ ３．ＩＤ ＳＣＲＯＬＬ ＳＰＥＥＤ ↵ ４．ＳＰＥＥＤ ０ ｄｏｔ ( 0 - +256 ) ３．ＩＤ ＳＣＲＯＬＬ ＳＣＲＯＬＬ ＯＮ／ＯＦＦ ↵ ４．ＳＣＲＯＬＬ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ ２．ＩＤ ＣＨＡＲＡＣＴＥＲ ＩＤ ＳＣＲＯＬＬ ３．ＩＤ ＳＣＲＯＬＬ ＤＩＲＥＣＴＩＯＮ ↵ ( +1 - +9 ) ３．ＩＤ ＢＬＩＮＫ ＩＤ ＢＬＩＮＫ ＯＮ／ＯＦＦ ↵ ４．ＩＤ ＢＬＩＮＫ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ ４．ＤＩＲＥＣＴＩＯＮ □ＬＥＦＴ ■...

  • Page 109

    14. Appendix 99 ０．ＳＤＩ ＳＥＴＴＩＮＧ ＳＤＩ ２（３Ｇ－ＳＤＩ－ＬｖＡ） s d i 1 と 同 様 ３．ＬＯＧＯ ＬＥＶＥＬ ＬＥＶＥＬ ０ ↵ ４．ＬＥＶＥＬ ０ １００ｈ （ ０％） ( 1 0 0 h - e b 0 h ) ２．ＬＯＧＯ ＬＯＧＯ ＯＮ／ＯＦＦ ↵ ３．ＬＯＧＯ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ ２．ＬＯＧＯ ＬＯＧＯ ＢＡＣＫＧＲＯＵＮＤ ↵ ３．ＬＯＧＯ ＢＡＣＫＧＲＯＵＮＤ □ＯＮ ■ＯＦＦ ( 1 0 0 h - e b 0 h ) ３．ＬＯＧＯ ＬＥＶＥＬ ＬＥＶＥＬ １ ↵ ４．ＬＥＶＥＬ １ ５９０ｈ （ ３３％） ( 1 0 0 h...

  • Page 110

    14. Appendix 100 14.2.7 aes/ebu menu ０．ＡＥＳ／ＥＢＵ ＳＥＴＴＩＮＧ ＡＥＳ／ＥＢＵ １ １．ＡＥＳ／ＥＢＵ １ ＡＥＳ／ＥＢＵ ＴＩＭＩＮＧ ↵ ２．ＡＥＳ／ＥＢＵ ＴＩＭＩＮＧ ０ （５１２ｆｓ） ( ± 5 1 1 ) １．ＡＥＳ／ＥＢＵ １ ＡＵＤＩＯ ＯＮ／ＯＦＦ ↵ ２．ＡＵＤＩＯ ＯＮ／ＯＦＦ □ＯＮ ■ＯＦＦ １．ＡＥＳ／ＥＢＵ １ ＲＥＳＯＬＵＴＩＯＮ ↵ ２．ＲＥＳＯＬＵＴＩＯＮ ■２０ｂｉｔ □２４ｂｉｔ １．ＡＥＳ／ＥＢＵ １ ＥＭＰＨＡＳＩＳ ↵ ２．ＥＭＰＨＡＳＩＳ □５０／１５ □ＣＣＩＴＴ ■ＯＦＦ １．ＡＥＳ／ＥＢＵ １...

  • Page 111

    14. Appendix 101 14.2.8 wclk menu ( ± 511 ) １．ＷＣＬＫ ＴＩＭＩＮＧ ０ （５１２ｆｓ） ０．ＷＣＬＫ ＳＥＴＴＩＮＧ ＷＣＬＫ ＴＩＭＩＮＧ ↵.

  • Page 112

    14. Appendix 102 14.3 firmware update history this manual is written for firmware version 1.1. To view the firmware version, select utility setting → version display → sys . Ver. 1.1 • [utility] snmp community has been added to the ethernet item. • [utility] the display format of version display has...

  • Page 113

    Lt 4600a 此标志适用于在中国销售的电子信息产品,依据2006年2月28日公布的 《电子信息产品污染控制管理办法》以及sj/t11364-2006《电子信息产品污染 控制标识要求》，表示该产品在使用完结后可再利用。数字表示的是环境保护使 用期限，只要遵守与本产品有关的安全和使用上的注意事项，从制造日算起在数 字所表示的年限内，产品不会产生环境污染和对人体、财产的影响。 产品适当使用后报废的方法请遵从电子信息产品的回收、再利用相关法令。 详细请咨询各级政府主管部门。 产品中有毒有害物质或元素的名称及含量 部件名称 有毒有害物质或元素 hazardous substances in each...

  • Page 114

    Leader electronics corp. 2-6-33 tsunashima-higashi, kohoku-ku, yokohama 223-8505, japan phone:81-45-541-2123 fax:81-45-541-2823 http://www.Leader.Co.Jp feb. 2, 2017 ver. 2 (fw ver. 1.1).