- DL manuals
- Lectronics
- Computer Hardware
- DM84
- Hardware And Software Installation Manual
Lectronics DM84 Hardware And Software Installation Manual
Summary of DM84
Page 1
Dm84 digital audio processor hardware and software installation guide rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date:.
Page 2
Dm84 installation guide lectrosonics, inc. 2.
Page 3
Dm84 installation guide rio rancho, nm 3 important safety instructions this symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure -- voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to i...
Page 4
Dm84 installation guide lectrosonics, inc. 4 introduction the purpose of this guide is to assist in the setup and operation of a typical dm84 system. This guide as- sumes familiarity with the dm84 digital audio proces- sor, its components and software menus and setup screens. To get the most out of ...
Page 5
Dm84 installation guide rio rancho, nm 5 table of contents important safety instructions................................................ 3 introduction ............................................................................. 4 unpacking the unit ....................................................
Page 6
Dm84 installation guide lectrosonics, inc. 6 audio inputs unbalanced sources unbalanced audio sources (positive and ground) include items such as consumer vcr’s, dvd players, etc., and may use both two wire and three wire cables. In either case, the positive output from the source should be connecte...
Page 7
Dm84 installation guide rio rancho, nm 7 microphone number 2: from specification sheet: v ph (min) = 9 v i mic (max.) = 2 ma v ph = 15 v - (1k)(.002a) v ph = 15 v - 2v = 13 v since the calculated vph is greater than the vph from the microphone specification sheet, this is an accept- able situation. ...
Page 8
Dm84 installation guide lectrosonics, inc. 8 when the dm84 output is connected to a balanced input, wire it as shown here. Dm out + - destination + - dm out to balanced input (3-wire) shield programmable inputs programmable inputs are provided to enable external control over a variety of parameters....
Page 9
Dm84 installation guide rio rancho, nm 9 expansion i/o ports the four rj45 connectors on the rear panel are used to interconnect lecnet2™ units together. These ports are only used to transfer digital audio information via the digital audio network interface (dani) between the units. Warning: the exp...
Page 10
Dm84 installation guide lectrosonics, inc. 10 dani bus expansion i/o ports the four rj45 connectors on the rear panel are used to interconnect lecnet2™ units together. These ports are only used to transfer digital audio information via the digital audio network interface (dani) between the dm series...
Page 11
Dm84 installation guide rio rancho, nm 11 control system interconnections in addition to a windows ® based computer system, the dm84 can be controlled by external serial control system using the rs-232 interface, such as those from crestron ® and amx ® . 1: gnd 2: in 1 3: in 3 4: in 5 5: in 7 25 13 ...
Page 12
Dm84 installation guide lectrosonics, inc. 12 installing lecnet2 ™ software and usb driver software installer - windows installation the example shown her illustrates the installation pro- cedure using a windows operating system. The screens that appear at each step using another operating sys- tem ...
Page 13
Dm84 installation guide rio rancho, nm 13 3. The end user license agreement screen appears. Click on i agree to continue. 4. The installer will automatically download to a folder on your pc, or you can choose which folder it should be stored in. 5. Click on next to complete the installation. When th...
Page 14
Dm84 installation guide lectrosonics, inc. 14 usb driver installer - windows installation the example shown her illustrates the installation pro- cedure using a windows operating system. The screens that appear at each step using another operating sys- tem will vary, but the general steps are very s...
Page 15
Dm84 installation guide rio rancho, nm 15 4. The end user license agreement screen appears. Click on i agree to continue. 5. The installer will walk you through installation. When complete, the final screen will appear. Click on finish to close the installation..
Page 16
Dm84 installation guide lectrosonics, inc. 16 initial setup the initial setup of a dm84 system is a relatively simple three step process: connect the unit to the computer, turn on the computer and select the appropriate control panel, preset the input, matrix and output. This process assumes that le...
Page 17
Dm84 installation guide rio rancho, nm 17 the dm84 can be configured in the installation or a configuration file can be created off line in advance. The minimum required setup to pass audio includes: inputs, matrix and outputs. Input and output filters, compressors and delays are used to tailor the ...
Page 18
Dm84 installation guide lectrosonics, inc. 18 service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnect- in...
Page 19
Dm84 installation guide rio rancho, nm 19.
Page 20: Limited One Year Warranty
Dm84 installation guide lectrosonics, inc. 20 28 february 2018 limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has bee...