1. DL manuals
  2. Lectrosonics
  3. Transmitter
  4. D4
  5. Instruction Manual

Lectrosonics D4 Instruction Manual

Other manuals for D4: Instruction Manual
Manual is about: Digital Wireless System

Summary of D4

  • Page 1

    D4 digital wireless system instruction manual rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date:.

  • Page 2

    D4t/d4r lectrosonics, inc. 2.

  • Page 3

    4-channel digital wireless system rio rancho, nm, usa 3 introduction the d4 digital wireless system was designed as a special purpose system for location production in film and television. A typical application for this system is in television production as part of what is commonly called a “bag sys...

  • Page 4

    D4t/d4r lectrosonics, inc. 4 general technical description d4t transmitter the transmitter can accept up to four inputs from digi- tal or analog sources. The inputs can be configured as follows: • four analog inputs using all four jacks • two digital inputs using jack 1 and two balanced analog input...

  • Page 5

    4-channel digital wireless system rio rancho, nm, usa 5 d4r receiver the receiver employs two complete rf sections for true diversity reception. The signals from both anten- nas are independently decoded and error-corrected, and the diversity system uses all digital data and tim- ing reference infor...

  • Page 6

    D4t/d4r lectrosonics, inc. 6 front and rear panels on both the d4t and the d4r, the front panel interface contains a power switch, an lcd display and eight push buttons. The d4t has one antenna jack and the d4r has two. The d4r front panel also contains a jack for headphones. When the units are powe...

  • Page 7

    4-channel digital wireless system rio rancho, nm, usa 7 navigating the lcd navigation through setup screens is the same on the transmitter and receiver. The main window will display audio levels for all active channels while the system is operating. Press the func button to enter the setup menu. Fun...

  • Page 8

    D4t/d4r lectrosonics, inc. 8 transmitter general settings tuning menu use up/down arrows to select menu item and press func to enter setup use up/down arrows to select frequency, then press func to return to menu audio trim use up/down arrows to select menu item and press func to enter setup note: t...

  • Page 9

    4-channel digital wireless system rio rancho, nm, usa 9 transmitter audio trim setup from the main window, press func and then select the menu item “audio trim” and press func again. The setup screen will vary slightly depending upon which aes3 mode has been selected and whether the 2-channel or 4-c...

  • Page 10

    D4t/d4r lectrosonics, inc. 10 receiver general settings tuning selection use up/down arrows to select menu item and press func to enter setup use up/down arrows to select frequency, then press func to return to menu audio level use up/down arrows to select menu item and press func to enter setup not...

  • Page 11

    4-channel digital wireless system rio rancho, nm, usa 11 receiver audio level setup from the main window, press func and then select the menu item audio lev. And press func again. The setup screen will vary slightly depending upon which aes3 mode has been selected and whether the 2-channel or 4-chan...

  • Page 12

    D4t/d4r lectrosonics, inc. 12 transmitter aes3 modes the transmitter can be set up in three different con- figurations with the aes3 modes menu for 4-channel operation: analog analog analog analog digital digital analog analog not used ch 1 digital digital not used not used ch 2 digital digital ch 3...

  • Page 13

    4-channel digital wireless system rio rancho, nm, usa 13 finding clear frequencies it is best to check for interference before selecting a frequency. Turn the receiver on and leave the trans- mitter off. Observe the rf level indicator in the main window to see if signal is present. Weak rf level str...

  • Page 14

    D4t/d4r lectrosonics, inc. 14 parts and accessories transmitter power supples • lectrosonics dcr12/a8u (replacement power supply) power supply for d4t & d4r; 100-240 vac, 50/60 hz input; 12 vdc (regulated), 800 ma max. Output. • lectrosonics dcr15/1a6u switching power supply with a universal socket ...

  • Page 15

    4-channel digital wireless system rio rancho, nm, usa 15 antenna • amjr-915 adjustable antenna for d4r and d4t. Supplied with transmitter and receiver (reverse gender sma connector). Audio cables • mcsrxlr receiver output cable; ta3f to male xlr 3-pin; 12 in. Length • mcsrxlrf transmitter input cabl...

  • Page 16

    D4t/d4r lectrosonics, inc. 16 firmware updates as new versions of the firmware become available, updates are accomplished with a software utility and simple procedure. In many cases, updates must be made to both transmitter and receiver to ensure com- patibility and provide the latest feature set. T...

  • Page 17

    4-channel digital wireless system rio rancho, nm, usa 17 fcc notice note: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in ...

  • Page 18

    D4t/d4r lectrosonics, inc. 18 service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equip- ment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the inter- connecting cables and t...

  • Page 20: Limited One Year Warranty

    28 october 2011 581 laser road ne • rio rancho, nm 87124 usa • www.Lectrosonics.Com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.Com limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provid...