- DL manuals
- Lectrosonics
- Recording Equipment
- DM84
- Hardware And Software Installation Manual
Lectrosonics DM84 Hardware And Software Installation Manual
Summary of DM84
Page 1
Dm84 digital audio processor hardware and software installation guide rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date:.
Page 2
Dm84 installation guide lectrosonics, inc. 2 important safety instructions this symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure -- voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you ...
Page 3
Dm84 installation guide rio rancho, nm 3 table of contents important safety instructions .................................................................................................................................................................. 2 table of contents ...............................
Page 4
Dm84 installation guide lectrosonics, inc. 4.
Page 5
Dm84 installation guide rio rancho, nm 5 introduction the purpose of this guide is to assist in the setup and operation of a typical dm84 system. This guide as- sumes familiarity with the dm84 digital audio proces- sor, its components and software menus and setup screens. To get the most out of the ...
Page 6
Dm84 installation guide lectrosonics, inc. 6 installing the dm84 system into a rack the dm84 occupies a single rack space and there are no special ventilation requirements. Mount with 4 rack screws using the appropriate mounting holes. It is recommended to use nylon washers to prevent damage to the ...
Page 7
Dm84 installation guide rio rancho, nm 7 examples: microphone number 1; from specification sheet: v ph (min) = 11 v i mic (typical) = 4 ma v ph = 15 v - (1k)(.004a) v ph = 15 v - 4v = 11 v since the calculated vph is equal to vph from the microphone specification sheet, this is a marginal situation....
Page 8
Dm84 installation guide lectrosonics, inc. 8 led is on when the programmable output is active 380 ohms programmable output pin 380 ohms led is off when the programmable output is active programmable output pin gnd (from programmable i/o pins 1, 8, 13) 1n4001 or equiv. External dc voltage source ( re...
Page 9
Dm84 installation guide rio rancho, nm 9 programmable inputs and outputs wiring diagram example dm84 rear panel expansion i/o ports the four rj45 connectors on the rear panel are used to interconnect lecnet2™ units together. These ports are only used to transfer digital audio information via the dig...
Page 10
Dm84 installation guide lectrosonics, inc. 10 1: gnd 2: in 1 3: in 3 4: in 5 5: in 7 25 13 14 1 6: in 9 7: in 11 8: gnd 9: out 1 10: out 3 11: out 5 12: out 7 13: gnd 14: +5v 15: in 2 16: in 4 17: in 6 18: in 8 19: in 10 20: +5v 21: out 2 22: out 4 23: out 6 24: out 8 25: +5v programmable inputs / o...
Page 11
Dm84 installation guide rio rancho, nm 11 installing lecnet2 ™ software and usb driver lecnet2™ is a graphic user interface (gui) designed to allow easy setup and monitoring of dm84 compo- nents using windows ® 2000 or xp computer systems. Lecnet2™ includes the necessary control panels to configure ...
Page 12
Dm84 installation guide lectrosonics, inc. 12 5. When the driver installation is complete, the final page of the wizard appears. Click finish to complete the lecnet2™ usb driver installation. Installation of additional units (or lecnet 2™ devices) the windows xp operating system regards all lecnet2™...
Page 13
Dm84 installation guide rio rancho, nm 13 usb driver installation (windows 2000) first time installation when a lecnet2™ device is connected to a comptuer system running the windows ® 2000/xp operating system for the very first time, the windows found new hardware wizard automatically opens. Use the...
Page 14
Dm84 installation guide lectrosonics, inc. 14 initial setup the initial setup of a dm84 system is a relatively simple three step process: connect the unit to the computer, turn on the computer and select the appropriate control panel, preset the input, matrix and output. This process assumes that le...
Page 15
Dm84 installation guide rio rancho, nm 15 the dm84 can be configured in the installation or a configuration file can be created off line in advance. The minimum required setup to pass audio includes: inputs, matrix and outputs. Input and output filters, compressors and delays are used to tailor the ...
Page 16: Limited One Year Warranty
Dm84installationguide.Pmd 15 march 2007 581 laser road ne • rio rancho, nm 87124 usa • www.Lectrosonics.Com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.Com limited one year warranty the equipment is warranted for one year from date of purchase against defects in materia...