1. DL manuals
  2. Lectrosonics
  3. Transceiver
  4. DR Receiver/DB Transmitter
  5. Instruction Manual

Lectrosonics DR Receiver/DB Transmitter Instruction Manual

Manual is about: Digital Secure Wireless System

Summary of DR Receiver/DB Transmitter

  • Page 1

    Dsw system dr receiver/db transmitter instruction manual rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date: essential setup steps 1) install receiver modules, antennas and connect to a power supply (see page 6) 2) install transmitter batteries and antenn...

  • Page 2

    Dsw digital wireless system lectrosonics, inc. 2 fcc notice for dr receiver note: this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interfer...

  • Page 3

    Dsw digital wireless system rio rancho, nm 3 introduction dsw (digital secure wireless) is designed for no-com- promise applications where performance and security are the highest priority. A completely new digital architecture was developed for the dsw wireless system. Extended operating range riva...

  • Page 4

    Dsw digital wireless system lectrosonics, inc. 4 receiver front panel headphone output a standard 1/4 inch jack and retractable volume control knob allows monitoring of individual channels or a mix of all channels. Lcd and control interface all settings for the receiver and transmitter can be adjust...

  • Page 5

    Dsw digital wireless system rio rancho, nm 5 receiver rear panel antenna connections standard 50 ohm bnc jacks accept input from the an- tennas. A built-in multi-coupler distributes the antenna signal to the six receiver modules, and also to the out jack to deliver the signal to an additional receiv...

  • Page 6

    Dsw digital wireless system lectrosonics, inc. 6 removing receiver modules 1. Turn the mainframe power off. 2. Remove the retaining clip by pressing the top side- ways to release it from the slot in the side panel. Then pull upward to remove it. 3. Pull outward on the module to release the connec- t...

  • Page 7

    Dsw digital wireless system rio rancho, nm 7 audio output wiring - analog the analog audio output wiring is as follows: (+) 1 (-) shield shield (+) (-) 2 3 (+) 1 (-) shield shield (+) 2 3 (+) 1 (-) shield shield (+) 2 3 dr output audio input balanced with 3-wire cable unbalanced with 3-wire cable un...

  • Page 8

    Dsw digital wireless system lectrosonics, inc. 8 receiver lcd interface all settings can be made from the front panel keypad and lcd interface, including transmitter settings if it is connected to the receiver with the key cable. The con- trol interface consists of membrane switches, a rotary encode...

  • Page 9

    Dsw digital wireless system rio rancho, nm 9 navigating the menus from the main window, press the encoder to open the menu select screen. Lower bar describes the highlighted menu top bar lists active menu the menu selections includes links to the rx and tx menus and system level choices. Rotate the ...

  • Page 10

    Dsw digital wireless system lectrosonics, inc. 10 menu map and icons receiver and transmitter setup or adjustments to settings can be completed using the receiver lcd interface. The menus are organized into three groups, as shown here. The top menu includes system setup and connec- tions, frequency ...

  • Page 11

    Dsw digital wireless system rio rancho, nm 11 the tx menu (transmitter menu) is used to config- ure and store the settings for all transmitters that will be used in the system. These settings, stored in the receiver memory, can be transferred from the receiver to the transmitter during setup with th...

  • Page 12

    Dsw digital wireless system lectrosonics, inc. 12 (tx menu cont’d) lf rolloff adjusts the point at which the low frequency audio in the transmitter begins to roll off. This “knee” can be set at 35, 50, 70, 100, 120 or 150 hz. Tx phase reverses the polarity of the audio signal in the transmitter to m...

  • Page 13

    Dsw digital wireless system rio rancho, nm 13 software installation the supplied software for the dsw system is available on disk or downloaded from the web site at: www.Lectrosonics.Com/wdsupport the software will run on windows or mac computers. The procedure for installing it varies between down-...

  • Page 14

    Dsw digital wireless system lectrosonics, inc. 14 mac installation launch your browser and go to: http://lectrosonics.Com/wdsupport/xap/wirelessdesigner.Html when the wireless designer introductory screen ap- pears, right click and choose install wireless design- er onto this computer... You may nee...

  • Page 15

    Dsw digital wireless system rio rancho, nm 15 db transmitter steve 494.500 -40 -20 0 mute battery status led key verification led power button menu navigation buttons return to previous screen usb port for firmware updates programmable function switch antenna port microphone/line input jack db trans...

  • Page 16

    Dsw digital wireless system lectrosonics, inc. 16 powering on in operating mode press and hold the power button until a counter on the lcd progresses from 1 to 3. When you release the button, the unit will be operational with the rf output turned on and the main window displayed. Hold for rf on ...3...

  • Page 17

    Dsw digital wireless system rio rancho, nm 17 navigating menus the lcd/keypad interface makes it easy to browse the menus and make the selections for the setup you need. When the unit is powered up in either the operat- ing or the standby mode, press menu/sel on the keypad to enter a menu structure ...

  • Page 18

    Dsw digital wireless system lectrosonics, inc. 18 db transmitter menu map from the main window, navigate with the arrow buttons to the desired menu item and press menu/sel to enter the setup screen. Sel back freq. Select option with arrow buttons use arrow buttons to select value 22 gain sel back ga...

  • Page 19

    Dsw digital wireless system rio rancho, nm 19 copying transmitter settings to and from the receiver connect the key cable from the jack labeled key on the front of the receiver to the micro usb port on the side of the transmitter. If transmitter settings are defined in the receiver, they can be tran...

  • Page 20

    Dsw digital wireless system lectrosonics, inc. 20 system setup these instructions apply to setup using the front panel lcd. If you will be using wireless designer for setup, instructions are in the help files supplied with the soft- ware. Install receiver modules turn power off on the dr mainframe. ...

  • Page 21

    Dsw digital wireless system rio rancho, nm 21 frequency selection manual selection may be necessary if frequencies are mandated by an authority, such as a major sporting event. You can manually set the frequencies and set- tings for the transmitters in the receiver, then connect a transmitter and tr...

  • Page 22

    Dsw digital wireless system lectrosonics, inc. 22 select begin in the setup screen and press the en- coder to start the process. Scanning will proceed one at a time on each receiver, from the lowest numbered one to the next higher numbered one. Each scan pass takes about 20 seconds. After the scan o...

  • Page 23

    Dsw digital wireless system rio rancho, nm 23 adjust receiver analog audio output level the analog audio output of the receiver is set at maxi- mum, and lower levels are achieved with an attenuator to reduce the signal level to match the level require- ments of other equipment. This means that there...

  • Page 24

    Dsw digital wireless system lectrosonics, inc. 24 accessories drkeycable encryption/settings transfer cable dcr15/4au power supply .475” o.D . Locking collar with 5/16”-32 thread input: 100-240 vac, 50/60hz,1.8a output: 15 vdc 4000ma, 60 watt cable length: 48 inches 21499 ac power cord for dcr15/4au...

  • Page 25

    Dsw digital wireless system rio rancho, nm 25 specifications system operating frequencies: 470.100 - 691.175 mhz in 25 khz steps sampling size and rate: 24-bit, 48 khz digital modulation: 8psk symbol rate: 128 k data compression: proprietary adpcm encryption: aes 256-ctr (per fips 197 and fips 140-2...

  • Page 26

    Dsw digital wireless system lectrosonics, inc. 26 service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equip- ment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the inter- con...

  • Page 27

    Dsw digital wireless system rio rancho, nm 27.

  • Page 28: Limited One Year Warranty

    17 june 2015 581 laser road ne • rio rancho, nm 87124 usa • www.Lectrosonics.Com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.Com limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided ...