Ifbr1a/e01 uhf multi-frequency belt-pack ifb receiver instruction manual rio rancho, nm, usa www.Lectrosonics.Com fill in for your records: serial number: purchase date:.
Ifbr1a/e01 lectrosonics, inc. 2 introduction thank you for selecting the lectrosonics frequency agile, r1a ifb receiver. The design is the result of extensive engineering experience with the most up to date components for demanding professional applica- tions. The receiver will operate with any lect...
Ifb receiver rio rancho, nm 3 table of contents safety notes ............................................................................................................................................................................................2 introduction .......................................
Ifbr1a/e01 lectrosonics, inc. 4 the ifbr1 was upgraded to the ifbr1a by adding a number of important and useful features: (1) two rotary hex switches to manually set the operating frequency, (2) automatic sensing/control of a mono phone plug to eliminate the mono/binaural switch, and (3) a multi- co...
Ifb receiver rio rancho, nm 5 figure 4 - r1a block diagram 0 1 2 3 4 5 6 7 8 9 a b c d e f 0 1 2 3 4 5 6 7 8 9 a b c d e f figure 3 - frequency adjustment figure 2 - headphone cord strain relief headphone jack (fig. 1 & fig. 2) on the front panel is a 3.5mm mini phone jack to ac- commodate a standar...
Ifbr1a/e01 lectrosonics, inc. 6 receiver normal operation (already programmed) 1. Set the frequency of the receiver to match the frequency of the transmitter by using the two hex rotary switches located on the side of the receiver under the sliding door. The 1.6m switch is for “coarse” adjustment (1...
Ifb receiver rio rancho, nm 7 to open the battery compartment door, push the door up and away from the case with your thumb, then swing open. 1 2 figure 5 - battery replacement the battery you use in the r1a receiver should be a 9 volt alkaline or lipolymer rechargeable type. Lithium batteries can a...
Ifbr1a/e01 lectrosonics, inc. 8 troubleshooting led not lit • battery not installed or depleted • power switch not on. No sound in headphone • audio level turned all the way down. • headphone plug not inserted fully. • defective headphone • transmitter not operating. (see separate transmitter manual...
Ifb receiver rio rancho, nm 9 replacement parts and accessories bezelkitr1a (full kit) belt clip, bezel, sliding door, belt clip bumper, mounting screws individual parts: 26377-1 bezel 25901 sliding door ifbr1-m000r belt clip assembly 35747 bumper for belt clip 28528 belt clip screw, 4-40 x 1/4 (1 r...
Ifbr1a/e01 lectrosonics, inc. 10 operating frequencies: block 470 470.100 - 495.600 block 19 486.400 - 511.900 block 20 512.000 - 537.500 block 21 537.600 - 563.100 block 22 563.200 - 588.700 block 23 588.800 - 607.900 and 614.100 - 614.300 block 24 614.400 - 639.900 block 25 640.000 - 665.500 block...
Ifb receiver rio rancho, nm 11 service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnect- ing cables and th...
24 june, 2010 581 laser road ne • rio rancho, nm 87124 usa • www.Lectrosonics.Com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.Com limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided...
