Q uick s tart g uide fill in for your records: serial number: purchase date: this guide is intended to assist with initial setup and operation of your lectrosonics product. For a detailed user manual, down- load the most current version at: www.Lectrosonics.Com l-series wireless microphone system lr...
Lectrosonics, inc. 2 fccid:dbzlmbc1 lectrosonics, inc. Made in u.S.A. Ic: 8024a-lmbc1 614.4 - 691.1 mhz model: lmbc1 s/n xxxxx ir 5 623.400 -40 -20 0 a ir port -2 0 -1 0 ba t pwr/func -10 -20 audio 5 623.400 -40 -20 0 a controls and features.
Www.Lectrosonics.Com 3 ir port audio out this device complies with part 15 of the fcc rules. Operation is subject to the condition that this device does not cause harmful interference. Can rss-gen/cnr-gen can ices-3 (b)/nmb-3(b) model: lr-xx made in the usa serial no. Xxxxx frequency block xxx (xxx....
Lectrosonics, inc. 4 keypad and lcd interface 5 623.400 -40 -20 0 a rf link led glows blue when a valid rf signal is being received. Batt led glows green when the batteries are good. As the batteries are drained, the led will turn to a steady red at a mid-point during their life, then begin to blink...
Www.Lectrosonics.Com 5 smart tune frequency ir sync tx block b1 b1 na 23 na 21 22 23 sel back use arrow keys to select desired scanning range sel ir sync press sel back frequency block 21 b1 555.300 mhz press sel to select desired adjustment step b1 use arrow keys to select desired frequency ir sync...
Lectrosonics, inc. 6 system setup procedures summary of steps 1) install receiver batteries and select the battery type in the setup screen or connect power. 2) select frequency step size in the receiver. 3) select the compatibility mode in the receiver. 4) find a clear operating frequency (two meth...
Www.Lectrosonics.Com 7 mode 3 is a special compatibility mode for use with another brand of wireless. Contact the factory for details. 200 series works with legacy lectrosonics models such as all um200, uh200 and ut200 series transmitters. 100 series works with lectrosonics um100 transmitters. Eu di...
Lectrosonics, inc. 8 cursor scrolls across screen during scanning when the scan is complete a screen will appear briefly to display the frequen- cy chosen by smart tune, and then it will change to ir sync. If you are using a lectrosonics transmitter that has an ir ports, the settings can be transfer...
Www.Lectrosonics.Com 9 press menu/sel to zoom in on the image. Scroll using the buttons as de- scribed above. Rf energy clear spectrum after scrolling the marker to a spot in the clear spectrum in the display, press back open a menu with three options. Use the arrow keys to select the option, then p...
Lectrosonics, inc. 10 5) adjust transmitter input gain note: this adjustment is very important, since it will determine the signal to noise ratio and dynamic range that the system will deliver. Lectrosonics l-series transmitters: the two bicolor modulation leds on the transmitter control panel provi...
Www.Lectrosonics.Com 11 input gain control some transmitters from brands other than lectrosonics can also be used if the appropriate compatibility mode set is set in the receiver. Observe the audio level meter on the lr receiver lcd as you adjust the input gain on the transmitter to see the modulati...
Limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warr...
