- DL manuals
- Lectrosonics
- Transmitter
- SMa Series
- Instruction Manual
Lectrosonics SMa Series Instruction Manual
Summary of SMa Series
Page 1
Sma series instruction manual super miniature belt-pack transmitters with digital hybrid wireless™ technology sma single battery, 100 mw rm remote control digital hybrid wireless us patent 7,225,135 fill in for your records: serial number: purchase date: rio rancho, nm, usa www.Lectrosonics.Com.
Page 2
Sma series lectrosonics, inc. 2.
Page 3
Super-minature belt pack transmitters thank you for selecting a lectrosonics sm series ultra-miniature transmitter. The unique design provides specialized features for professional applications: • outstanding rf operating range • superb audio quality • ultra-lightweight, corrosion resistant housing ...
Page 4
Sma series general technical description wideband design digital hybrid transmitters use ±75 khz wide deviation for an excellent signal to noise ratio and wide dynamic range. The dsp controlled input limiter features a wide range dual envelope design which cleanly limits input signal peaks over 30 d...
Page 5
Super-minature belt pack transmitters low frequency roll-off the low frequency roll-off can be set for a 3 db down point at 35, 50, 70, 100, 120 and 150 hz to control sub sonic and very low frequency audio content in the au dio. The actual roll-off frequency will vary slightly depend ing upon the...
Page 6
Sma series controls and functions modulation leds battery lcd compartment up arrow cover plate audio input jack battery compartment thumb screw down arrow pwr led audio button freq button lcd screen the lcd is a numeric-type liquid crystal display with several screens that allow settings to be made ...
Page 7
Super-minature belt pack transmitters setup with the lcd six screens are used to set up and operate the sm. These screens are used to set the operating frequency, adjust the audio input level, select the compatibility mode or lock the control panel and power down the transmitter. Audio screen the au...
Page 8
Sma series when the timer reaches zero, the transmitter’s controls are locked. The lcd will display the locked condition as long as the arrow buttons are held, then revert back to the previous screen when either button is released. With the controls locked, the audio and freq buttons can still be us...
Page 9
Super-minature belt pack transmitters operating instructions power up and boot sequence 1) ensure that good batteries are installed in the unit. (see battery installation.) 2) simultaneously press and hold the audio and freq buttons until the power on boot sequence is initiated. (see power on timer....
Page 10
Sma series setting transmitter operating frequency frequency displayed the operating frequency of the in mhz sm can be displayed either in mhz or as a two-digit hexadeci mal number. (see controls and functions, freq button.) the frequency displayed as sm’s operating frequency can two-digit hexadeci...
Page 11
Super-minature belt pack transmitters locking or unlocking the control panel control panel locked the lock mode protects the transmitter from accidental changes to its settings. 1) ensure the sm setup is complete (operating fre quency, audio level, compatibility mode, sensitivity to remote control)...
Page 12
5 4 2 sma series 5-pin input jack wiring the wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro phones may require extra jumpers or a slight variation on the diagrams shown. It is virtually imposs...
Page 13
Super-minature belt pack transmitters microphone cable termination for non-lectrosonics microphones ta5f connector assembly mic cord stripping instructions 1 2 3 4 5 view from solder side of pins 0.3" 0.15" crimping to shield and insulation shield insulation crimp these fingers to contact the shield...
Page 14
Sma series microphone rf bypassing when used on a wireless transmitter, the microphone element is in the proximity of the rf coming from the transmitter. The nature of electret microphones makes them sensitive to rf, which can cause problems with the microphone/transmitter compatibility. If the elec...
Page 15
Super-minature belt pack transmitters rio rancho, nm 15 balanced and floating line level signals *note: if the output is balanced but center tapped to ground, such as on all lectrosonics receivers, do not connect pin 3 of the xlr jack to pin 4 of the ta5f connector. Ta5f plug xlr jack fig. 7 compati...
Page 16
Sma series rm remote control operating instructions important: the remote control (rc) mode must be enabled on your sm series transmitter for the rm to function with it. For instructions, refer to page 8 of this publication. Rm front panel controls the rm unit gives you remote control of sm series t...
Page 17
Super-minature belt pack transmitters operating notes • the sensitivity to the remote control varies with the trans mitter’s audio level setting and the microphone used, but it is always possible to make it work with a sufficiently loud remote signal at close range. • if the sma is configured to re...
Page 18
Sma series troubleshooting before going through the following chart, be sure that you have a good battery in the transmitter. It is important that you follow these steps in the sequence listed. Symptom possible cause transmitter pwr led off 1) battery is inserted backwards or dead. 2) transmitter no...
Page 19
Super-minature belt pack transmitters symptom possible cause hiss and noise -- audible dropouts 1) transmitter gain (audio level) far too low. 2) receiver antenna missing or obstructed. 3) transmitter antenna broken or missing. 4) operating range too great. 5) signal interference. Turn off transmitt...
Page 20
Sma series lectrosonics, inc. 20 smkitta5 connector kit for sma series transmitters, 5-pin ta5f plug with sleeve smbcdn machined, wire belt clip for sma/smv transmitters, antenna down included accessories sma/smv: place thermal insulation pad on back of unit, as pictured. Smbcupsl spring-loaded mach...
Page 21
Super-minature belt pack transmitters specifications and features operating frequencies: block 470 470.100 - 495.600 block 19 486.400 - 511.900 block 20 512.000 - 537.500 block 21 537.600 - 563.100 block 22 563.200 - 588.700 block 23 588.800 - 607.900 and 614.100 - 614.300 block 24 614.400 - 639.900...
Page 22
Sma series service and repair if your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the trou...
Page 23
Super-minature belt pack transmitters rio rancho, nm 23.
Page 24: Limited One Year Warranty
Limited one year warranty the equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warr...