LED Lighting FOLLOWSPOT 1200 HMI User Manual - page 3
fig. 4
Before connecting the unit to the mains, make sure that the working voltage and frequency correspond to the values
indicated on the label (fig. 4).
The FOLLOWSPOT 1200 HMI is made to work at a working voltage of 230V 50Hz; 10 A.
Connect the projector to the power supply through the feed box placed on the ballast (fig. 4).
For the power supply connection, do as follows:
1) open the feed box using a thin screw-driver and gently force the two lateral little tongues (fig. 4/a);
2) the connections from the unit to the power supply source are described in fig. 4/a;
3) close the feed box pressing on its cover;
4) at the end, connect the plug of the projector to the ILME socket of the ballast (fig. 4/a).
!
The plug of the projector must be used only for the connection to the ballast.
Any other use could damage the lamp.
To start on the projector there is a green switch ON / OFF (fig. 4).
2
COL
COL
COL
COL
COLOURS CHANGER SYSTEM ASSEMBLING
OURS CHANGER SYSTEM ASSEMBLING
OURS CHANGER SYSTEM ASSEMBLING
OURS CHANGER SYSTEM ASSEMBLING
OURS CHANGER SYSTEM ASSEMBLING
FOLLOWSPOT 1200 HMI
CODE 991223
ON / OFF
SWITCH
PROFILE SYSTEM AND BLA
PROFILE SYSTEM AND BLA
PROFILE SYSTEM AND BLA
PROFILE SYSTEM AND BLA
PROFILE SYSTEM AND BLACK OUT
CK OUT
CK OUT
CK OUT
CK OUT
fig. 3
fig. 3a
The FOLLOWSPOT 1200 HMI comes with a colours changer system (fig. 6), to assamble it, do as follows:
At the front of the projector there are 4 support connections where to mount the colours changer system (fig. 6).
At the back of the colours changer system, there are 4 guide-eyes.
Pull the safety spring at the front of the colours changer system (fig. 6) and precisely connect the 4 guide-eyes to
the 4 support connections, leave free the safety spring making sure that the colours changer system is well stable.
The colours changer system is able to be equipped with No. 5 coloured filters (gelatine).
To insert the gelatines, do as follows:
1) unfasten the three screws of the filter-holder (fig. 6);
2) insert the gelatine;
3) fasten the three screws.
PLUG
FUSE
HANDLE
ILME SOCKET
LABEL
It is recommended to use
only filters with an high
temperature resistance.
ZOOM AND FOCUS
ZOOM AND FOCUS
ZOOM AND FOCUS
ZOOM AND FOCUS
ZOOM AND FOCUS
To regulate the zoom and focus use the two knobs (fig. 6) placed on the right side of the projector. The light beam
amplitude can be regulated from a minimum of 8° to a maximum of 17° (fig. 2).
The FOLLOWSPOT 1200 HMI is provided with a profile system of 4 profile blades.
Insert the profile blades (fig. 3) in their appropriate side slots (fig. 6) to cut the beam to the required shape.
In the upper part of the projector has been made an appropriate room with a track to insert the Iris and the
Gobo-holder (fig. 6), available on request (ref. to standard package and fig. 3/a).
The FOLLOWSPOT 1200 HMI is provided with the black out function. It is possible to cut out the entire light beam
using the lever placed at the right side of the projector (fig. 6).
Profile blades
Iris
Gobo-holder
SLOT SIDE
CONNECTION T
CONNECTION T
CONNECTION T
CONNECTION T
CONNECTION TO THE POWER SUPPL
O THE POWER SUPPL
O THE POWER SUPPL
O THE POWER SUPPL
O THE POWER SUPPLY
Y
Y
Y
Y
HANDLE
The unit must be connected to the earth. The inobservance of these instructions automatically makes
the guarantee expiring.
IMPORTANT
!
FEED BOX
fig. 4/a
THIN SCREW-DRIVER
CABLE CLAMP
L = PHASE (Brown)
N = NEUTRAL (Blue)
= EARTH (Green - Yellow)