Summary of SUPER-HERO 440
Page 1
Super-hero 440 keep this manual for future needs.
Page 2: Contents
Contents 1. Introduction…………………………..……………………………………………………………..….03 2. General guidelines…………….………………………………………………………………….…03 3. Safety instructions……………………………………………………….....………………………04 4. Cleaning and maintenance………………………………………………...……………………05 5. Technical parameters…………………..…………………………………..………………………06...
Page 3: Introduction:
Thank you for your patronage! We are confident that our excellent products and service can satisfy you. For your own safety, please read this user manual carefully before installing the device. In order to install, operate, and maintain the lighting safety correctly. We suggest that the installation...
Page 4: Safety Instructions
To extreme heat, moisture or dust. Please don’t project the beam onto combustible substances. The minimum distance between light-output from the projector and the illuminated surface must be more than 0,5 meter. If you use the quick lock cam in hanging up the fixture, please make sure the quick lock...
Page 5: Cleaning And Maintenance
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out the plug by tugging the power cord. During initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the dev...
Page 6
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to the lights. 1) clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust. 2) clean the fan each week. 3) a detailed electric check by approved el...
Page 7: Fixed Gobo Wheel
Fixed gobo wheel : amimation disc ： rotating gobo wheel ： 25.9mm*25mm.
Page 8
Functions of buttons.
Page 9
Reversal of the display to activate this function, press up and down keys simultaneously while the display is in the rest mode.This status will be memorised and maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again. Using the me...
Page 12: Dmx Channels
Dmx channels channel st 30 channel ， extended 34 channel. 1 cyan colour wheel 2 magenta colour wheel 3 yellow colour wheel 4 colour 1 5 colour 2 6 colour 3 7 stopper / strobe 8 dimmer 9 dimmer fine 10 static gobo change 11 animation disk insertion 12 animation disk rotation 13 rotating gobo select 1...
Page 13
1 cyan colour wheel 0-255 linear cyan movement 2 magenta colour wheel 0-255 linear magenta movement 3 yellow colour wheel 0-255 linear yellow movement 4 colour 1 0 empty position 28 empty + soft filter 50 soft filter 80 soft filter + lavender 100 lavender 129 lavender + cto 3200k 150 cto 3200k 181 c...
Page 14
7 stopper / strobe 0-3 light off 4-103 strobe at linearly variable frequency from low (1 flash/sec) to high (12 flashes/sec) 104-107 light on 108-207 pulsation at linearly variable speed from slow (0.5 flash/sec) to fast (12 flashes/sec) 208-212 light on 213-225 random strobe at low frequency 226-23...
Page 15
Fast (600 bpm) 166 - 170 gobo 2 shakes at variable speed from slow (24 bpm) to fast (600 bpm) 171 - 175 gobo 3 shakes at variable speed from slow (24 bpm) to fast (600 bpm) 176 - 181 gobo 4 shakes … 182 - 186 gobo 5 shakes … 187 - 191 gobo 6 shakes … 192 - 197 gobo 7 shakes … 198 - 202 gobo 8 shakes...
Page 16
93 - 111 gobo 5 112 - 129 gobo 6 130 - 150 gobo 1 shakes at variable speed from slow to fast 151 - 171 gobo 2 shakes at variable speed from slow to fast 172 - 192 gobo 3 shakes … 193 - 213 gobo 4 shakes … 214 - 234 gobo 5 shakes … 235 - 255 gobo 6 shakes … rotating gobo effect disabled if beam mode ...
Page 17
Diffusion in 0.02 seconds at maximum speed. 19 zoom 0-225 zoom linearly moves from narrow to wide beam 20 frost 0-255 focus moves linearly from far to near position. Focus lenses move from farthest to nearest position in 1.11 seconds at maximum speed. 21 focus fine 0-255 fine focus positioning 22 be...
Page 18: Important
Levels range and staying in this range for 5 seconds. 128-255 complete reset all-effects reset sequence passing through the unused levels range and staying in this range for 5 seconds. 29 lamp control 0 - 25 unused range 26-100 lamp off lamp switch-off passing through the unused levels range and sta...
Page 19: Vector More Time Table
Vector more time table remark the product has perfect performance and integrity packaging. All users should be strictly comply with the warning and operating instructions as stated. Or we aren’t in charge of any result by misusing. Any damage resulting by misuse is not within the company’s warranty....