DL manuals
Legacy
Tools
L1310
Owner's Instructions Manual

Legacy L1310 Owner's Instructions Manual

Manual is about: Manually Operated Grease Guns

Page of 10

Download

Print this page

Bookmark us

Loading Your Grease Gun

L1320

L1325

L1310

L1350, L1355

L1355FZ

Cartridge Loading

Suction Loadng

Filler Pump Loading

Pull follower rod from barrel

and lock into place.

Pull follower rod from barrel

and lock into place.

WARNING:

Do not load gun with air operated

grease pump. Damage to unit

will occur and warranty

will be voided.

Unscrew barrel from head.

Wipe bulk filler nipple until clean.

Remove cap from end

of grease cartridge

Insert open end of gun barrel

two inches below surface of grease.

Insert bulk filler nipple

into loader pump receptacle.

Insert cartridge into barrel,

open end down.

Slowly pull back follower rod

to draw in grease. Pull follower rod

back all the way and lock into place.

Pump grease until 8 inches of follower rod

is exposed.

(Between the follower rod handle and barrel

cap)

Remove pull tab from top

of grease cartridge.

Make sure cartridge is pushed

down completely.

Screw barrel back into head.

Pump grease until barrel is full.

(When barrel is full, rod can be pulled out

without spring tension)

Screw barrel into head until snug.

Unlock follower rod and push into barrel.

Release follower rod.

Unscrew barrel slightly.

(Approximately two revolutions)

If no bleeder valve is installed,

unscrew barrel slightly.

(Approximately two revolutions)

(Skip this step if bleeder valve is installed)

Push follower rod into barrel.

Release follower rod.

Prime.

(see “Priming Your Grease Gun”)

Push follower rod into barrel.

Screw barrel into head.

Depress bleeder valve to release air.

(If bleeder valve is installed)

Prime.

(see “Priming Your Grease Gun”)

Prime.

(see “Priming Your Grease Gun”)

Begin greasing.

Owner’s Instructions

Manually Operated Grease Guns

Part No. : L1320, L1325, L1310, L1350, L1355, L1355FZ

Legacy Manufacturing Company

Marion, IA, U.S.A.

Ph: 319.373.7305

Fx: 319.373.7309

service@legacymfg.com

legacymfg.com

INS1000

Published 11/15/2013 Revised 5/27/2016

1 2 3 4 5 6 7 Next › »

Summary of L1310

Page 1
Loading your grease gun l1320 l1325 l1310 l1350, l1355 l1355fz cartridge loading suction loadng filler pump loading pull follower rod from barrel and lock into place. Pull follower rod from barrel and lock into place. Warning: do not load gun with air operated grease pump. Damage to unit will occur ...
Page 2
Priming your grease gun re-priming your grease gun greasing a zerk (grease fitting) grease gun terms attachments lever action grease gun pistol grip grease gun point outlet up at least 45 degrees. Using slow, complete strokes, stroke handle repeatedly until grease flows without air. (should require ...
Page 3
Troubleshooting your grease gun warranty problem cause(s) remedy grease does not flow when handle is stroked. Gun needs to be re-primed see “re-priming your grease gun” grease cartridge is still capped • check to ensure caps have been removed from both ends of cartridge grease cartridge or barrel is...
Page 5
Instructivo del propietario pistolas graseras operadas manualmente componente núm. : l1320, l1325, l1310, l1350, l1355, l1355fz legacy manufacturing company marion, ia, ee.Uu. Tel: 319.373.7305 fx: 319.373.7309 service@legacymfg.Com legacymfg.Com ins1000 published 11/15/2013 revisado 5/27/2016 cómo ...
Page 6
Cómo cebar la pistola grasera cómo volver a cebar la pistola grasera cómo engrasar un engrasador zerk terminología de las pistolas graseras accesorios pistola grasera accionada con palanca empuñadura de la pistola pistola grasera apunte la salida hacia arriba al menos 45 grados. Utilizando carreras ...
Page 7
Solución de problemas de la pistola grasera garantía problema causa(s) remedio la grasa no fluye al bombear la empuñadura: es necesario volver a cebar la pistola (consulte "cómo volver a cebar la pistola grasera") no le quitó la tapa al cartucho de grasa. • verifique que haya quitado las tapas de lo...
Page 8
Instructions d’utilisation manually operated grease guns réf.: l1320, l1325, l1310, l1350, l1355, l1355fz legacy manufacturing company marion, ia, États-unis téléphone: 319.373.7305 télécopieur: 319.373.7309 service@legacymfg.Com legacymfg.Com ins1000 publié le 11/15/2013 révisée 5/27/2016 chargemen...
Page 9
Amorçage de la pompe à graisse réamorçage de la pompe à graisse graisser au moyen d'un graisseur terminologie de la pompe à graisse accessoires pompe à graisse à levier pompe à graisse à poignée pistolet pointer la buse vers le haut d'un angle d'au moins 45 degrés. Actionner lentement le levier à fo...
Page 10
Dépannage de la pompe à graisse garantie problème cause(s) mesure corrective il ne s'écoule pas de graisse lorsque la poignée est actionnée. La pompe doit être réamorcée. La cartouche de graisse est encore bouchée • vérifier que les capuchons ont bien été retirés des deux côtés de la cartouche la ca...