1. DL manuals
  2. Legend
  3. Indoor Fireplace
  4. 738JLN
  5. Installation & Owner's Manual

Legend 738JLN Installation & Owner's Manual

Manual is about: Gravity Vent Gas Insert

Summary of 738JLN

  • Page 1

    This manual contains instructions to install the engine only. A front is also required to complete this installation. A barrier screen is pro- vided with the front. Refer to the manual sup- plied with the front for installation. — do not store or use gasoline or other fl ammable vapors and liquids i...

  • Page 2

    Table of content designed and manufactured by / for miles industries ltd. 190–2255 dollarton highway, north vancouver, bc, canada v7h 3b1 tel. 604-984-3496 fax 604-984-0246 www.Valorfi replaces.Com © copyright miles industries ltd., 2015 the information contained in this installation manual is belie...

  • Page 3: Safety Precautions

    Safety precautions ! Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be su...

  • Page 4: Safety And Your Fireplace

    Safety and your fireplace please follow these important child safety precautions and recommendations, • parts of your valor fireplace become extremely hot while in operation. • the glass viewing window temperature can exceed 500 f at full capacity. Momentary contact with a hot glass surface can caus...

  • Page 5: Do Not Put

    Operating your fireplace for the first time when operating your new fi replace for the fi rst time, some vapors may be released due to the burning of curing compounds used in the manufacture of the appliance. They may cause a slight odor and could cause the fl ames to be the full height of the fi re...

  • Page 6

    Bottom of window (wider frame) owner’s information cleaning your fireplace important - glass cleaning - mineral deposits one of the by-products of the combustion process in a gas appliance is a mineral which can show up as a white fi lm on the ceramic glass of the viewing door. The composition of th...

  • Page 7

    Owner’s information 5. Replace the front or trim with the barrier screen attached. Checking pilot and burner flames a periodic check of the pilot and burner fl ames should be made. Check after the fi re has been on for at least 30 minutes. The pilot fl ame must cover the tip of the thermocouple prob...

  • Page 8

    Owner’s information your fireplace’s vent safety switch this appliance is equipped with a vent safety switch which, when activated, will turn off the burner and pilot if the vent is blocked, disconnected, or if there is excessive down draught. If the safety switch is activated, wait for it to cool o...

  • Page 9

    Remote control operation your fi replace remote control helps you get the comfort, convenience and aesthetics you want from your gas fi replace. The remote controls your fi replace in different ways. Important: before you begin, please note that on this system, the settings of time, temperature and ...

  • Page 10

    Remote control operation setting the fl ame use this setting when you want a particular fl ame level. For instance, you want to watch fl ames burn at their highest level and you don’t mind if the room is too hot. 1. To raise the fl ame, press and hold the ▲ button until the flame gets to the desired...

  • Page 11

    Options required kits* venting approved venting accessories as per local codes. Inner fronts (choose one) 741—contemporary front with barrier screen 4003360 742—traditional cast front with barrier screen 4003293 743—fenderfire double door front 744—fenderfire single door front 745—clearview front wi...

  • Page 12

    Lighting instructions for your safety read before lighting warning: if you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow ...

  • Page 13

    X x ratings model ng lpg gas natural propane altitude (ft.)* 0-4,500 feet* input maximum (btu/h) 24,000 24,000 input minimum (btu/h) 6,500 13,000 manifold pressure (in w.C.) 3.95 9.5 minimum supply pressure (in w.C.) 5.0 11.0 maximum supply pressure (in w.C.) 10.5 14.0 main burner injector marking 8...

  • Page 14

    Overview this appliance, as supplied, may only be installed in an existing unal- tered, functioning solid-fuel burning fi replace with a working fl ue and con- structed of non-combustible material. This appliance is approved for installation into combustible type con- struction only when using the 7...

  • Page 15

    28-5/8” (727 mm) 19-1/2” (495 mm) 7-7/8” - 9-7/8“ (200 - 251 mm) varies with outer trim options 20” (508 mm) gas inlet gas connection optional outer trim or surround sold separately 12 - 14” (305 - 357 mm) varies with outer trim options x y dimensions cavity check that masonry step does not interfer...

  • Page 16

    9” (229 mm) a b do not put furniture or objects within 36” (914 mm) of the front of appliance combustible mantel clearances *measure taken from the underside of the mantel to fi nished hearth or surface that the unit is sitting on. Finishing materials combustible materials: material such as wood, co...

  • Page 17

    Approved termination required max. 36” offset at 10’-0” min. Vertical 3” liner 3” min. Bend radius m in. 10 f eet (with off set) m in. 8 f eet (without off set) minimum vent liner radius allowable vent configurations minimum vent lengths. For other allowable configurations, refer to the venting tabl...

  • Page 18

    Installation planning installer—read this first 1. You need to know from the homeowner what accessories (surround, door, etc.) will be installed with this fi replace; 2. Unpack the appliance. 3. Check that you have everything. 4. Clean cavity, chimney, ash dumps, clean-outs. 5. Install venting pipe....

  • Page 19

    Unpack the appliance beware of sharp edges! Wear gloves! 1. Unpack the appliance. 2. Unpack any loose items from around the appliance and check against the pack content list provided in the documentation package. 3. Remove the window and set aside in a safe place to avoid damage. 4. Verify that you ...

  • Page 20: Option 2B

    Connect vent important: this appliance’s venting system requires room air to be used in the combustion process. 1. Rough-in one 3” diameter vent liner into the existing chimney system from the roof. Be careful not to tear or damage the liner in the process. Leave plenty of liner at the bottom to fac...

  • Page 21

    Supply pressure test tapping manifold pressure test tapping installation connect gas supply the gas supply inlet connection is a 3/8” npt female connector and is located on the left hand side of the control valve. Use only new black iron or steel pipes or copper tubing if acceptable—check local code...

  • Page 22

    Push-on connector connect remote control receiver 1. Connect the wiring harness to the receiver box, by pushing the wire connector on to the receiver circuit board. The plug will only go on one way so please ensure that the wires are pointing up and the slot in the board is in line with the tab on t...

  • Page 23

    Port cover installed install ceramic bricks the following guidelines apply for all brick liners. 1. Inside the fi rebox, on the top of each side, release the screw of the side brick anchors (one per side) just enough to allow them to rotate. 2. Place the rear panel against the back of the fi rebox, ...

  • Page 24

    Install ceramic logs unpack the ceramic logs very carefully to avoid damaging the fragile material. Install the logs as shown below. Please note that the position of the logs is critical to ensure proper performance of the appliance. 1. Place the rear log on the sheet metal support centering it side...

  • Page 25

    6. Place the lower end of the center right log onto the pin on the front right log. Rest the narrow end in the notch into the rear log. 7. Pour some ceramic loose coals on each side of the logs to hide the sheet metal work. Do not put any coal into the pilot area. Notch in rear log pin in front righ...

  • Page 26

    Bottom of window (wider frame) open open close close ng flashback shield (for lpg only) lpg air shutter slider open close lpg ng air shutter slider & cover hot glass warning plate re-install and check window 1. To refi t the window, hook its top part to the fi rebox’s opening frame. Make sure that t...

  • Page 27

    Packing contents: 1 wall bracket a 2 screws b 1 screw c 2 wall anchor d 1 spacer e (detach before assembly) 1 wall bracket f switch plate alternative 1 alternative 2 alternative 3 install handset wall holder the remote control kit for this fi replace comes complete with a wall-mounted holder. This h...

  • Page 28: Lor

    Warranty 1. Extended warranty coverage for a period of up to ten (10) years, miles industries ltd., (the “company”) or its appointed distributor will at its option pay the initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in mater...

  • Page 29

    Spare parts code description part number 1 exhaust slide assembly 4000127 2 port cover 4001820ah 3 log support 4004353 4 side bricks anchors (2) 4001283 5 top mounting bracket 4000136az 6 side mounting brackets (2) 4000135az 7 window assembly 4001378 8 burner assembly ng 4001180 burner assembly lpg ...

  • Page 30

    Spare parts ng lpg 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 24 27 26 25 30 28 29 49 50 51 52 48 41 42 43 44 45 46 47 12a ng lpg 11a 32 35a, 35b 36 37 38 39 40 53 18 23 19 20 21 22 17 31 30 owner’s information.

  • Page 31

    Thank you ... For purchasing a valor by miles industries. Your new radiant gas heater is a technical appliance that must be installed by a qualifi ed installer. Please fi ll in the information below. The information provided will be used for customer records only. Online warranty registration at www...

  • Page 32

    Tape shut thank you for choosing a valor product postage needed miles industries ltd. 190 - 2255 dollarton highway north vancouver, bc v7h 3b1 canada fold here online warranty registration at www.Valorfi replaces.Com.