Model eh-19pcu electric-hydraulic rebar cutter read safety and instructions carefully before using this tool. Save this owners manual & operating instructions fascut industries inc. 7248 inama rd., sauk city, wi 53583 phone: (608)643-6678 fax: (608)643-2682 www.Fascut.Com specifications and prices s...
Safety requirements for your own safety and protection, do not attempt to operate this tool until it is completely assembled and installed according to the instructions… and until you read and understand all the safety requirements. For power tools warning indicates a potentially hazardous situation...
13. Avoid unintentional starting. Do not carry the tool with finger on the switch. Be sure switch is off when plugging in. Use switch lock behind trigger switch when not in use. 14. Avoid using an extension cord. An extension cord should not be used unless absolutely necessary. Use of an improper ex...
8. If the tool makes an abnormal sound during operation, discontinue use immediately. Return the tool to fascut industries for repair. 9. Do not add hydraulic oil if the tool is warm or immediately after heavy duty operation. Oil will be under a slight pressure when tool is warm. 10. Avoid skin cont...
#3 - is the electrical power supply correct? Use this tool only with a power supply that meets the rating indicated on the tool. #4 - using an extension cord? An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electr...
3. Position the rebar to be cut at a right angle to the tool head and secure by adjusting the adjusting screw. This will hold the rebar at a right angle to the cutting direction. 4. Confirm where the dangerous range is. Cut pieces may fly off with tremendous force within the dangerous range as shown...
Emergency manual release for emergency reasons, it may become necessary to manually retract the moving cutting blade. To do this, loosen the release valve no more than ¼ turn using the m5 hex key wrench. The moving blade will return to its starting position. Securely retighten the valve. Strictly av...
Maintenance 1. Changing the blades. If a blade is dull or damaged, immediately replace with a new blade. Cutting with dull or loose blades will damage the tool. Unplug the tool before starting maintenance of any kind. 2. Check the length of the carbon brushes every six months. Unplug the tool and lo...
Storage method the tool should be stored in a dry, high or locked up place out of reach of children. Clean prior to long term storage. Coat metal parts with a rust inhibitor. Trouble shooting if the remedy listed below does not solve the problem, the tool must be returned to fascut industries for se...
Lobster eh-19pcu fascut industries inc. March 1, 2011 index # description code price ea. Qty. Req. 1 cutter head 40626 $662.61 1 2 washer, spring lock, m6 25592 $0.20 4 3 screw, socket head cap, m6x20 25593 $0.45 2 4 cutting blade w/washers & screws 29044 $37.50 2 5 rod seal 25595 $18.29 2 6 oil pis...
39 screw, support, m12x35 25623 $5.20 1 40 support screw locking nut, m12 25624 $1.30 1 41 key, piston 25628 $5.10 1 42 pump frame (frame only) 25625 $415.50 1 43 steel ball, 4.8 mm (3/16) 12360 $0.20 1 44 o-ring, relief valve, p-3 10333 $0.35 1 45 relief valve 25606 $14.13 1 46 label, name plate 40...
85 cable tie 24316 $0.30 1 86 oil tank case housing 40354 $327.12 1 87 o-ring, oil tank, p-32 25813 $3.20 1 88 oil seal, 12-28-7 28071 $13.28 1 89 washer, m5 28032 $0.10 4 90 screw, socket head cap, m5x30 w/lock 28033 $0.50 4 91 trigger switch spring plate 26698 $8.10 1 92 grab handle 40627 $44.80 1...
