1. DL manuals
  2. Loctite
  3. Controller
  4. CL10
  5. Operation Manual

Loctite CL10 Operation Manual

Manual is about: LED Controller

Summary of CL10

  • Page 1

    Equipment operation manual intensity % time s cl10 single led controller item no. 1514636 set loctite cl10 single led controller item # 1514636.

  • Page 2

    2 contents ............................................................................................................................................................................ 1 contents ............................................................................................................

  • Page 3

    3 1 caution info: warning instructions in this manual and on labels are classified and described below. Warning: this means that possible death or serious injury to the operator may result if these instructions are ignored and the equipment handled incorrectly. Forbidden ： this symbol means that the...

  • Page 4

    4 1.1 safety instruction forbidden  disassembly and modification is prohibited.  discontinue use if power cable is frayed or damaged.  should an abnormal condition occur such as smoking, abnormal smell or noise, turn off the power immediately and disconnect the power cable from the ac outlet. Whe...

  • Page 5

    5 2 overview loctite® cl10 single led controller is a uv light source that emits a spot of light at a wavelength of 365 or 405nm for use in adhesive light cure bonding applications. Advantage ： 1. Over 20,000 working hours. 2. No ir emission resulting in low temperature curing. Will not damage parts...

  • Page 6

    6 4 installation 4.1 capacity min .Space required for the equipment 4.2 dimension intensity % time s cl10 single led controller item no. 1514636 set xs -1 ac 10 0~ 24 0v 50 /6 0h z fu se :2 am p 25 0v ac please check the unit for any mechanical defects. If there is any shipping damage do not install...

  • Page 7

    7 4.3 caution to prevent heat damage, set the unit horizontally on a level surface. Failure to position the unit properly may cause damage. Avoid placing next to high voltage equipment or next to a heat source. Make sure nothing is placed on the power cable. 4.4 installation flow 1. Place the contro...

  • Page 8

    8 5 controller button and operating 5.1 component name and function 1. Power switch ：power on/off 2. Led head connector 3. Intensity display ： intensity setting data and information will be shown here, easy to read and edit. 4. Time display ：time setting data and information will be shown here, easy...

  • Page 9

    9 5.2 button and display instruction 5.2.1 button instruction arrow buttons ：edit settings set 5.2.2 display instruction intensity % time s 5.3 operating 5.3.1 startup power power switch ：power on/off. Set button ：confirm or enter menu. Intensity data information time data information warning please...

  • Page 10

    10 5.3.2 starting controller after finishing installation, plug in power cable, then press . The red led light inside the button will turn on when the unit is powered. 5.3.3 working mode if the led head is plugged in, the controller will automatically enter working mode. 5.4 parameter setting 5.4.1 ...

  • Page 11

    11 5.5 working mode setting in working mode, you can switch manual/timer mode by holding set button. In timed mode, the set time will be displayed. In manual mode, "off" will be displayed under time s. 5.6 working temperature press set once while in working mode to show the temperature of the led. 5...

  • Page 12

    12 6 shutdown step 1 ：press power button to turn off controller, red indicator will turn off at same time. Step 2 ：disconnect power cable..

  • Page 13

    13 7 troubleshooting error cause/demonstration action please check if power cable is plugged in properly. Plug in power cable properly. 1 ．display not on when turning on power button please check the fuse fuse type ：2amp, 250vac please check if led head is in working status. Exit working status, ent...

  • Page 14

    14 8 replacement parts name loctite® item no. Controller cl10 single led controller 1514636 cl10 led head, 365nm, 3mm, w/2.7m cable 1540715 cl10 led head, 365nm, 6mm, w/2.7m cable 1538499 cl10 led head, 365nm, 10mm, w/2.7m cable 1538505 cl10 led head, 365nm, 3mm, w/5m cable 1538504 cl10 led head, 36...

  • Page 15

    15 9 warranty henkel expressly warrants that all products referred to in this instruction manual for loctite® cl10 single led controller (hereafter called “products”) shall be free from defects in materials and workmanship. Liability for henkel shall be limited, as its option, to replacing those pro...

  • Page 16

    16 henkel corporation one henkel way rocky hill, ct 06067-3910 usa henkel canada corporation 2515 meadowpine boulevard mississauga, ontario l5n 6c3 canada henkel corporation automotive/ metals h.Q. 32100 stephenson hwy, madison heights 48071 usa henkel capital, s.A. De c.V. Calzada de la viga s/n fr...