1. DL manuals
  2. Loctite
  3. Dispenser
  4. SD10
  5. Operation Manual

Loctite SD10 Operation Manual

Manual is about: SD10 Digital Syringe Dispenser

Summary of SD10

  • Page 1

    Equipment operation manual vacuum pressure psi psi shot set exit teach program cycle timer manual dispense mode sd10 digital syringe dispenser loctite® sd10 digital syringe dispenser part number 1514629.

  • Page 2

    Table of contents 1 please observe the following.......................................................................................... 3 1.1 emphasized sections ............................................................................................ 3 1.2 items supplied ........................

  • Page 3

    1 please observe the following 1.1 emphasized sections danger! Refers to safety regulations and required safety measures that protect the equipment, operator, or other persons from injury. Caution! Emphasizes what must be done or avoided so that the unit or other property shall not to be damaged. No...

  • Page 4

    1.3 for your safety for safe and successful operation of the unit, read these instructions completely. If the instructions are not observed, the manufacturer can assume no responsibility. Damage to the power cord or the housing can result in live voltage.  check the power cord and the unit before e...

  • Page 5

    2 description - typical system set-up vacuum pressure psi psi shot set exit teach program cycle timer manual dispense mode sd10 digital syringe dispenser 4 5 3 2 1 front panel for service, spare parts, & repairs usa - (1) 860-571-5174 germany - (49) 89-9268-0 singapore - (65) 6266-0100 china - (86) ...

  • Page 6

    2.1 operating elements 1 control panel 2 adjustable air regulator 3 digital air output/vacuum display 4 suck back regulator 5 air output for syringe air line adapter 6 air input 7 xs-1, foot switch connector 8 power switch 9 power input (24vdc) 10 foot switch 11 power supply 12 syringe air line adap...

  • Page 7: 3 Technical Data

    3 technical data 3.1 energy requirements 3.1.1 electrical power supply 110 –240 vac; 50 –60 hz power consumption approx. 40 w internal control voltages 5 vdc; 24 vdc 3.1.2 pneumatics pneumatic supply min. 2 bar (29 psi); max. 12 bar (174 psi) quality filtered 10 μm, oil-free, non-condensing if the r...

  • Page 8: 4 Installations

    4 installations 4.1 environmental conditions – no condensing humidity – no splashing water 4.2 placement when the syringe piston is missing and the syringe is handled in an improper manner, the product can enter and contaminate the dispenser.  place the control unit in an elevated position above th...

  • Page 9

    5.2 set up 5.2.1 purging air from the syringe to avoid air bubbles during dispensing, the tip of the syringe must be purged of air. Hold the syringe over a container since product will flow out! Press the power switch to the position i (on). Using the pressure regulator (2), set the dispensing press...

  • Page 10

    If the dispense quantity is achieved too slowly, increase the dispense pressure and check the dispense quantity again. Repeat this sequence until the desired dispense quantity is achieved in an acceptable amount of time. 5.2.3 programs this mode of operation is used for precise repeatable dispensing...

  • Page 11

    Using the teach mode to set the dispense time. Press the button until the led above timer is lit. Press the button until the light above it flashes. Pressure the button or foot switch for the desired amount of time. Press the button to save the data. Press the button or foot switch to dispense. 5.2....

  • Page 12: 6 Cares And Maintenance

    6 cares and maintenance 6.1 care occasionally the o-ring of the syringe adaptor (12) should be lubricated with silicone grease. This will prolong the life of the o-ring. Clean hands after application of grease to assure surfaces to be bonded are clean. Otherwise bonding might fail. Failure to proper...

  • Page 13: 7 Troubleshooting

    7 troubleshooting type of malfunction possible causes correction –no power voltage present. Check the power voltage. –power switch (8) is in position o (off). Switch power switch (8) to position i (on). –power fuse has failed. Check/replace fuse. The digital display does not light. –control unit is ...

  • Page 14: 9 Warranty

    8 replacement parts and accessories description loctite item no. 10 ml clear syringe package 97207 30 ml clear syringe package 97244 10 ml air line adapters 97208 30 ml air line adapters 97245 foot switch 97201 filter regulator 985397 9 warranty warranty henkel expressly warrants that all products r...

  • Page 15

    Henkel corporation one henkel way rocky hill, ct 06067-3910 usa henkel canada corporation 2225 meadowpine boulevard mississauga, ontario l5n 7p2 canada henkel corporation automotive/ metals h.Q. 32100 stephenson hwy, madison heights 48071 usa henkel capital, s.A. De c.V. Calzada de la viga s/n fracc...