1. DL manuals
  2. Logic Controls
  3. Monitor
  4. PD6000
  5. User Manual

Logic Controls PD6000 User Manual

Other manuals for PD6000: Specifications, Specifications
Manual is about: PD3000/PD6000 Series Customer Displays 2 by 20 character display

Summary of PD6000

  • Page 1

    I customer displays 2 by 20 character display user manual models: pd3000/pd6000 series.

  • Page 2

    Ii notice the manufacturer of the pos pole display makes no representations or warranties, either expressed or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties of fitness for a particular purpose or for any indirect, special or consequential ...

  • Page 3: Table of Contents

    Iii table of contents features............................................................................1 model identification.....................................................2 carton contents ...........................................................2 installation...............................

  • Page 4: Features

    1 features the pd3000/pd6000 family of pole displays offers a wide range of high quality features and models to choice from. Listed below are the features incorporated into each pole display. Not all features are available in all models. The model identification chart will assist you in selecting th...

  • Page 5: Model Identification

    2 model identification pd3 or pd6 __ __ __ - __ __ blank = no pass thru pt = pass thru 25 = db25f connector to computer power adapter 0 = 120vac* command set 1 = 220vac 0 = logic controls* 1 = logic controls serial/parallel interface with pass-thru 0 = serial 9600 baud* 2 = special command set 1 (ae...

  • Page 6: Installation

    3 installation your pd3000/pd6000 family of pole displays has been pre- assembled to make the installation as simple as possible. Serial interface non-pass-thru models installation 1. Mount the pole display to the metal base plate using the mounting hardware provided. 2. The pole display can be used...

  • Page 7

    4 serial interface pass-thru models installation 1 mount the pole display to the metal base plate using the mounting hardware provided. 2 the pole display can be used in a freestanding mode or attached to the counter using the remaining mounting hardware. 3 connect the db25m connector to the periphe...

  • Page 8: Functional Test

    5 functional test the following test sequence will verify that your pole display is working properly. Before you start this procedure, you must install the pole display correctly as outlined under the installation section. The functional test should be done under msdos command prompt by booting up t...

  • Page 9

    6 pd3100-pt, pd3300-pt, pd3400-pt, pd3500-pt, pd6100-pt, pd6300-pt, pd6400-pt and pd6500-pt 1. Type “abcdefgh” and press enter key. The display will show “abcdefgh” on the first line. 2. Type “^apassthru” ( ^a represents ctrl-a ) and press enter key. The data will be passed through to the peripheral...

  • Page 10

    7 pd3190-pt, pd3390-pt, pd3490-pt, pd3590-pt, pd6190-pt, pd6390-pt, pd6490-pt and pd6590-pt 1. Type “echo abcdefgh>lpt1” and press enter key. The display will show “abcdefgh” on the first line. 2. Type “echo ^apassthru>lpt1” (^a represents ctrl-a) and press enter key. The data will be passed through...

  • Page 11

    9 parallel interface connector configuration all standard parallel pole displays will have a db25 male connector. It is connected to the printer port of the computer. 1. –strobe 2. Data 0 3. Data 1 4. Data 2 5. Data 3 6. Data 4 7. Data 5 8. Data 6 9. Data 7 10. –ack 11. Busy 12-17 nc 18-25 ground fo...

  • Page 12: Software Commands

    10 software commands logic controls pole displays are controlled by command codes and data from the computer. The model of pole display that you have will determine which command set works with your pole. Refer to the model identification chart for further information. For logic controls command set...

  • Page 13: Hardware Configuration

    11 hardware configuration serial pole displays were factory configured for serial rs232c interface using the following protocol: · 9600 baud rate · 8 data bits · 1 stop bit · no parity other optional baud rates are available with factory settings. Refer to the model identification chart for further ...

  • Page 14: Display Character Codes

    12 display character codes d7 0 0 0 0 0 0 0 0 d6 0 0 0 0 1 1 1 1 d5 0 0 1 1 0 0 1 1 d4 0 1 0 1 0 1 0 1 d3 d2 d1 d0 0 1 2 3 4 5 6 7 0 0 0 0 0 dp sp 0 @ p ‘ p 0 0 0 1 1 dc1 ! 1 a q a q 0 0 1 0 2 dc2 " 2 b r b r 0 0 1 1 3 dl dc3 # 3 c s c s 0 1 0 0 4 dim dc4 $ 4 d t d t 0 1 0 1 5 ms % 5 e u e u 0 1 1 0...

  • Page 15: General Specifications

    13 general specifications pd3000 pd6000 optical: number of rows 2 2 number of digits/row 20 20 dot matrix 5 x 7 plus underline 5x7 plus comma digit height) 0.20in. (5.0mm 0.44in. (11.25mm) digit width 0.14in. (3.5mm) 0.28in. (7.2mm) character format ascii ascii brightness (typical) 690 cd/m 2 700 cd...