- DL manuals
- M.T.H.
- Toy
- RAILKING N&W J WITHPROTO-SOUND 2.0READY-TO-RUN TRAIN SET
- Operating instructions manual
M.T.H. RAILKING N&W J WITHPROTO-SOUND 2.0READY-TO-RUN TRAIN SET Operating instructions manual - page 15
15
RailKing N&W J Steam Engine
The locomotive’s internal gearing was greased at the factory and should not
need additional grease until after 50 hours of operation or one year, whichever
comes first. To access the gear box, do the following:
1. Turn the engine upside down.
2. Remove the Phillips screw (marked “GREASE”) located at the fourth set of
drivers (counting from the front of the engine).
3. Use a grease tube dispenser to put a small amount (approx. 1-2 ml.) of
lithium-based grease into the gearbox.
4. Replace the screw.
You should also grease the leading and trailing locomotive truck tongues to
enhance their ability to slide on the chassis. Follow the grease points shown on
Fig. 10.
Grease Screw (G)
Body Mounting Screws
Body Mounting Screws
Lubricate Pivot Point (G)
Figure 10. Greasing Points on the Engine and Body Mounting Screws
Summary of RAILKING N&W J WITHPROTO-SOUND 2.0READY-TO-RUN TRAIN SET
Page 1
Railking n&w j with proto-sound 2.0 ready-to-run train set operating instructions your railking ® ready-to-run train set is complete with everything you need to get your model railroad up and running. This set includes a n&w j 4-8-4 steam locomotive, a set of three passenger cars, a transformer, a l...
Page 2
2 railking n&w j steam engine table of contents set up assembling realtrax ® 3 plugging in the transformer 4 lubricating the engine 4 priming the smoke unit 4 coupling the engine and car 5 remote control 6 basic operation operation buttons 7 volume control 8 proto-sound 2.0 operation activating prot...
Page 3: Set Up Checklist
3 railking n&w j steam engine set up checklist • assemble realtrax ® • connect the transformer • lubricate the train • place the engine and cars on the track and couple them together • apply power to run as described in the basic operation section of these instructions. Assembling realtrax ® unlike ...
Page 4: Connecting The Transformer
4 railking n&w j steam engine connecting the transformer the z-750 ® power supply included with this set provides an easy-to-use, safe power source for ac-powered trains and accessories. Plug the wire from the transformer into the remote lock-on’s center port, then plug the transformer into the wall...
Page 5: Coupling The Engine and Cars
5 railking n&w j steam engine if you choose not to prime the unit with fluid, turn the smoke unit switch located under the engine to the off position (see figure 5). Running the engine without a primed smoke unit may cause damage. See the “protosmoke unit operation” section of this book for more inf...
Page 6: Remote Control
6 railking n&w j steam engine remote control the railking ® remote control system included with this set uses wireless infrared technology, much like a television remote control, to allow users remote control of their trains from up to 15 feet away. The remote and lock-on replace the control box fou...
Page 7: Basic Operation
7 railking n&w j steam engine basic operation throttle up the power to your track. Give your train enough power so that the head light shines brightly. Then put the engine into motion by firmly pressing the direction button on your remote once. Operation buttons use the operation buttons on your rem...
Page 8: Volume Control
8 railking n&w j steam engine volume control – to adjust the volume of all sounds made by this engine, turn the master volume control knob located under the tender clockwise to increase the volume and counter-clockwise to decrease the volume (see fig. 8). Proto-sound 2.0 volume adjustment knob figur...
Page 9
9 railking n&w j steam engine proto-sound 2.0 operating instructions this manual contains the operating instructions for proto-sound 2.0 in conventional mode only. Instructions for accessing dcs command mode features accompany the dcs remote control system equipment. Because proto-sound 2.0 is an al...
Page 10
10 railking n&w j steam engine passenger station announcements (psa): your engine is equipped with a sound package of passenger station announcements that you can play when you pull into a passenger station. Each sequence described below will play as long as it is left on, randomly generating sounds...
Page 11: Tips On Using Psa
11 railking n&w j steam engine tips on using psa • you can terminate psa at anytime by turning off power to the track for 15 seconds. • you do not have to be in forward to use psa. At the conclusion of the full sequence, the train will pull away from the station in whatever direction you were going ...
Page 12: Proto-Coupler
12 railking n&w j steam engine proto-coupler ® operation this locomotive is equipped with a coil-wound proto-coupler for remote uncoupling action. Because the proto-coupler is controlled through the proto-sound 2.0 microprocessor, it does not require an uncoupling track section or modification to yo...
Page 13: Reset to Factory Defaults:
13 railking n&w j steam engine horn blasts will indicate that the engine has made the change. The engine will not change direction (including going into neutral) until you repeat the 1 whistle, 3 bells code to return the engine to its normal state, even if the engine is kept without power for extend...
Page 14: Maintenance:
14 railking n&w j steam engine maintenance: care of the remote control your railking remote control system should offer years of trouble-free service. There are a few things you can do to ensure trouble-free operation: • if your train responds inconsistently, replace old batteries with fresh ones. D...
Page 15
15 railking n&w j steam engine the locomotive’s internal gearing was greased at the factory and should not need additional grease until after 50 hours of operation or one year, whichever comes first. To access the gear box, do the following: 1. Turn the engine upside down. 2. Remove the phillips scr...
Page 16
16 railking n&w j steam engine cleaning the wheels, tires and track periodically check the locomotive wheels and pickups for dirt and buildup, which can cause poor electrical contact and traction and prematurely wear out the neoprene traction tires. Wheels and tires can be cleaned using denatured (n...
Page 17: Protosmoke
17 railking n&w j steam engine protosmoke ® unit operation this steam locomotive contains a smoke unit that outputs smoke through the smokestack on the boiler of the engine. The smoke unit is essentially a small heating element and wick that soaks up and then heats a mineral oil-based fluid that emi...
Page 18
18 railking n&w j steam engine locomotive light bulb replacement to replace the light bulb in the locomotive, follow these instructions and see the diagrams below: remove the locomotive boiler from its chassis as shown in figure 10. Once the body has been removed, rotate the headlight bulb counter-c...
Page 19
19 railking n&w j steam engine passenger car light bulb replacement to replace the interior light bulbs follow these instructions and see the diagrams below: 1. Turn the car over and remove the two mounting screws (as seen in figure 13-1) attaching the roof to the chassis. 2. Turn the car back over ...
Page 20
20 railking n&w j steam engine self-charging battery back-up the special nicad 7-cell 8.4v self-charging battery in this engine improves performance at any speed. It ensures that power to the sound system will remain on during directional changes, or when travelling over dirty track or switches. The...
Page 21: Railware Interactive Cd-Rom
21 railking n&w j steam engine railware interactive cd-rom m.T.H. Provides a free railware cd-rom in each ready-to-run set. It is full of helpful information on m.T.H. Product history, track planning software, a dealer finder, and information and video clips on loco-sound and proto-sound 2.0. Follow...
Page 22
22 railking n&w j steam engine installing adobe acrobat software to read some of the electronic documents included on the cd-rom, you will need to install the adobe acrobat reader ® if it is not already on your computer. To install the software: 1. On the desktop, click on the icon that says my comp...
Page 23: Troubleshooting Proto-Sound
23 railking n&w j steam engine troubleshooting proto-sound ® 2.0 problems although proto-sound 2.0 has been designed and engineered for ease of use, you may have some questions during initial operation. The following table should answer most questions. If your problem cannot be resolved with this ta...
Page 24
24 railking n&w j steam engine cab chatter lock-out volume battery psa remedy remedy remedy remedy remedy sometimes the cab chatter sounds don’t play. I can’t get the engine to run after i power up the transformer. It sits still with the engine sounds running. The engine won’t lock into forward, neu...
Page 25: Compatibility
25 railking n&w j steam engine psa remedy once in psa, the engine doesn’t go into reverse. When the psa enters its last sequence the bell automatically comes on. When psa is enabled, pressing the whistle and bell buttons has no effect. I push the direction button but the next sound clip in the seque...
Page 26
26 railking n&w j steam engine transformer compatibility and wiring chart note that many of the operational commands described in these instructions require a bell button, so if you are using a transformer other than the one included in this set and your transformer does not have its own bell button...
Page 27: Remote Control System:
27 railking n&w j steam engine additional features accessible with the dcs remote control system: while conventional mode operation of a proto-sound 2.0 engine yields wonderfully realistic sound and several train control features, command mode operation allows the user to access a world of command f...
Page 28
28 railking n&w j steam engine • proto-effects™ set up-user can select individual proto-effects™ operations to be active or inactive, including cab chatter, train wreck sounds, coupler sounds, and wheel clickety-clack sounds • direction control set up-user can set initial individual start-up directi...
Page 29
29 railking n&w j steam engine caution: electrically operated product: not recommended for children under 10 years of age. M.T.H. Recommends adult supervision with children ages 10 - 16. As with all electric products, precautions should be observed during handling and use to reduce the risk of elect...
Page 30
30 railking n&w j steam engine notes:______________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ________...
Page 31
31 railking n&w j steam engine notes:______________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ___________________________________________________ ________...
Page 32: Limited One-Year Warranty
Service & warranty information how to get service under the terms of the limited one-year warranty for warranty repair, do not return your product to the place of purchase. Instead, follow the instructions below to obtain warranty service as our dealer network is not prepared to service the product ...