M2 KT36XA Assembly Manual

Summary of KT36XA

  • Page 1

    Specifications model number ................................................ Kt36xa freq. Range..................................................... 14.0 - 14.35 mhz 21.0 - 21.45 mhz 28.0 - 29.0 mhz gain (free space) .............................................. See charts front to back ..............

  • Page 2: Kt36Xa Assembly Manual

    Tools: phillips head screw driver, ‘green’, 11/32” nutdriver, 7/16” wrench, 7/16” socket, socket wrench, tape measure, and a friend. Note: to prevent galling of the stainless steel hardware, apply a light coating of penetrox to all bolts and screws. The term ‘swage’ refers to a physical reduction ma...

  • Page 3: Kt36Xa Assembly Manual

    3. Capacitor assemblies onto longer 3/8” tubes locate the ten longer 3/8” diameter tubes. Upon inspecting the tubes, you’ll notice there are two holes drilled on one side only. The holes are to prevent moisture build up inside the capacitor tubes and to provide pressure equalization. Denote the hole...

  • Page 4: Kt36Xa Assembly Manual

    4. General assembly of half element sections we recommend assembling the half element sections on a clean, flat surface. There is an assembly drawing for each of the six elements with both the right and left halves shown on each page. We also recommend briefing yourself with the general directions b...

  • Page 5: Kt36Xa Assembly Manual

    5. Hf clamp plate pair assembly locate the 11 element clamp plates, the balun ‘l’-bracket, 2-1/2” u-bolt & saddle, and element clamp cap. Assemble the plates into six pairs with the radii facing each other using four 1/4-20 x 2” bolts. On one of the ‘alike’-pair combinations, attach the balun ‘l’-br...

  • Page 6: Kt36Xa Assembly Manual

    10. Element installation we advise that you elevate the antenna boom onto a couple of sawhorses or bucks for the remaining assembly steps. Use the dimension sheet as a guide to properly install the six elements onto the boom. If you have not labeled which side of the element faces towards the front ...

  • Page 7: Kt36Xa Assembly Manual

    15. Overhead guy support to prepare the overhead guy system, begin by temporarily installing a 2” u-bolt through the turnbuckle plate and into the top set of 2” u-bolt holes on the boom to mast plate. Add a couple of 5/16” nuts to hold it in place. Unscrew the turnbuckle eyes / hooks until only a th...

  • Page 8

    Kt36xa-half elemen-general assembly.

  • Page 9: Kt36Xa Assembly Manual

    Kt36xa assembly manual.

  • Page 10

    Rear driven element dimensions.

  • Page 11

    Front driven element dimensions.

  • Page 12

    1st director element dimension.

  • Page 13

    2nd director element dimension.

  • Page 14

    3rd director element dimensions.

  • Page 15

    Dual driven and t-match assemblies.

  • Page 16: Kt36Xa Dimension Sheet

    Kt36xa dimension sheet.

  • Page 17: Kt36Xa Parts & Hardware

    Description ..................................................................... Qty boom sections, 3" x .065” x 95” swaged .............................. 4 boom section, 3” x .065” x 28” straight ................................. 1 center sleeve, 7/8” x .058” x 36” str ...............................

  • Page 18: Kt36Xa Parts & Hardware

    In bag #6 clamp block, 3/8” ................................................................. 8 phasing line insulator .......................................................... 1 turnbuckle plate, 1/8” x 2” x 5" ............................................. 1 balun ‘l’-bracket, 1” x 1” x 4” ..........

  • Page 19: Box #1 Parts & Hardware

    Boom sec. 3” w/ eyebolt holes .................. 2 1 x 72" soe ........................................................... 10 bundle, 3/4 x 23" (6) & 3/4 x 21” (4) soe ........ 1 bundle, 3/4 x 12” sbe ....................................... 1 bundle, all 1/2” tubes .....................................

  • Page 20: Box #2 Parts & Hardware

    Boom sec. 3” soe, no holes ......................... 2 boom sec. 3” x 28” straight ......................... 1 oddball tube bundle ................................... 1 element, 3/4 x 48” soe ..................................... 2 capacitor tube bundle ................................ 1 short 3/8” ...