1. DL manuals
  2. M2
  3. Controller
  4. MT-3000A
  5. Installation Manual

M2 MT-3000A Installation Manual

Manual is about: Elevation Positioner

Summary of MT-3000A

  • Page 1

    Specifications model number ..................................................... Mt-3000a (elevation positioner) rotating torque ............................................... 4500 inch lbs. (at slowest speed) gear ratio ............................................................ 19200:1 rotation...

  • Page 2: Mt-3000A Pre Assembly Notes

    2 mt-3000a pre assembly notes length of cable terminal 1 & 2 minimum awg terminal 5 & 6 minimum awg 125 feet #18 awg #22-24 awg 125-200 feet #16 awg #22-24 awg 200-300 feet #14 awg #22-24 awg 300-450 feet #12 awg #22-24 awg for a successful installation there are six points that must be considered b...

  • Page 3

    3 mt-3000a pre-installation assembly all installations are unique in some way, which means it's ok to preassemble certain hardware, or rear- range the assembly process to meet specific site requirements. A quick review of the assembly notes and drawings should help firm up the appropriate strategy. ...

  • Page 4

    4 mt-3000a & axis assembly detail note: if you purchase d & are installing the optional limit switch kit. Limit swicth part s must be inst al led during this procedure. Refe r to limit switch kit p a ges be f o re ass e mbling part s & hardwares shown below..

  • Page 5

    5 drive sprocket & axis bearing detail.

  • Page 6: Leveling Bar Assembly

    6 leveling bar assembly the leveling bar is mainly an installation tool to help keep mounting pads parallel during main cross boom installation. Depending on your installation, topography & h-frame type, your leveling bar can be installed in many configurations. The leveling bar can be removed after...

  • Page 7: Mt-3000A Chain Installation

    7 mt-3000a chain installation 4 1 1. Install master link to chain and chain anchor. Note: for installation ease keep bolts on chain achors loose. Untill chain as been routed thru sprokets and secured on other end of d-ring. 2 2. Route chain thru sprokets as shown on picture #2. 4. Make sure and tigh...

  • Page 8

    8 chain & idler sprocket adjustment excessive chain slop or play may develop after using system for some time. We have incorporated in a chain adjustment to keep chain slop or play at a minimum. Please review drawings shown for more detailed information. To adjust system: 1. Remove the chain cover (...

  • Page 9: Gear Box Motor Detail

    9 gear box motor detail the new mt-3000ael has been outfitted with a high performance high efficiency gear box using all roller bearings and gear oil. The gear box has been assembled with a light coat of lubricat- ing oil. No load testing can be performed during ground set up and test before gear bo...

  • Page 10: Lsk-3000 Limit Switch Kit

    10 lsk-3000 limit switch kit note: limit plate must be installed to bearing adjustment body plate with; bolt, 1/4-20 x 1/2” (qty. 2) before it becomes un-accsesible. When installing bearing / adjustment body plate to axis assembly. (see photos for more information) limit stop block bolt, 1/4-20 x 1-...

  • Page 11: Lsk-3000 Limit Switch Kit

    11 lsk-3000 limit switch kit note: install limit switch box to motor. Route cables as shown below & refer to limit switch box picture for wiring details. Install limit switch box cover with screws supplied with cover. Limit switch box wiring detail black or mtr ccw/dwn white or mtr cw/up orange or r...

  • Page 12: Mt-3000A Parts & Hardware

    12 mt-3000a parts & hardware description qty axis assembly (welded) ............................................................................... 1 mast mount plate ......................................................................................... 1 “t” plate, coast side (welded) .............

  • Page 13: Mt-3000A Parts & Hardware

    13 description qty bolt, 1/4-20 x 1”, hex hd, ss ........................................................................ 4 nut, locking 1/4-20, ss ................................................................................ 5 screw, allen head cap 10-32 x 1-1/8”, ss ...............................

  • Page 14: 12 Month Limited Warranty

    14 12 month limited warranty this warranty gives you specific legal rights. You may also have other rights which will vary from state to state or province to province. M2 warrants the mt-3000ael positioner unit against defects in material and workmanship for a period of 12 months from date of purcha...