1. DL manuals
  2. MA
  3. Cash Counter
  4. NC-6000
  5. Service Manual

MA NC-6000 Service Manual

Manual is about: Compact Two Pockets Currency Discriminator

Summary of NC-6000

  • Page 1

    Nc-6000 compact two pockets currency discriminator service manual document version 1.0 oct 1 st , 2012 masterwork automodules tech corp ltd. 11f-3, 3, park st., nangang, 11503, taipei, taiwan support@automodules.Com copyright © 2011 masterwork automodules tech corp ltd. All rights reserved. This doc...

  • Page 2

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 2 - content chapter 1 introduction ................................................................................................. 5 1.1 a bout nc-6000 s ervice m anual ................

  • Page 3

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 3 - 4.5.1 ir status ....................................................................................................................................... 23 4.5.3 burn in ..............

  • Page 4

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 4 - 5.3.2.2 keypads ........................................................................................................................ 56 5.3.2.3 lcd display .......................

  • Page 5

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 5 - chapter 1 introduction 1.1 about nc-6000 service manual this manual is for the maintenance of nc6000 and it includes the disassembly process, spare part replacement, basic inspecti...

  • Page 6

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 6 - 1.4 contact information masterwork automodules tech corp ltd. Www.Automodules.Com address: 11f-3, 3, park st, nangang, 11503, taipei, taiwan tel: +886 2 2655 7997 fax: +886 2 2655 ...

  • Page 7

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 7 - chapter 2 nc-6000 outline 2.1 nc-6000 at a glance 3.5 inch color tft lcd display hopper guide top bill path open hopper control panel reject pocket stacker pocket bottom bill path ...

  • Page 8

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 8 - 2.2 specification 2.2.1 functional and mechanical specification sensors: ir array, mr, uv denomination detection: ir transmission dual user operation: yes available currencies usd,...

  • Page 9

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 9 - 2.2.3 interface specification 2.2.3.1 thermal printer (rs-232) (a) communication conditions item specification standard: eia rs-232c baud rate: 9600bps ,38400bps ,115200bps synchro...

  • Page 10

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 10 - 2.2.3.2 remote display (a) communication conditions item specification standard: uart baud rate: 115200bps synchronous method: asynchronous data format: start data parity stop 1 b...

  • Page 11

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 11 - 2.3 system overview.

  • Page 12

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 12 - chapter 3 maintenance 3.1 cleaning the cover of nc-6000 prepare a mixture of a gentle kitchen-use detergent (one that does not contain abrasive powder or strong chemicals such as ...

  • Page 13

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 13 - chapter 4 maintenance mode maintenance mode is for testing and maintaining nc-6000 only. Please follow the instruction as below when operating under the mode, or there is a risk t...

  • Page 14

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 14 - 4.1 test run – simple mode to test the feeding process with the four sets of ir trigger sensors in the bill path. 4.1.1 run – value list to check the gap adjustment by using the r...

  • Page 15

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 15 - 4.1.2 run – wavform to check the gap adjustment by using the graphic wave formed by the retrieved value. 1. Enter “run – wavform” by press the “ ” after selecting on the item. 2. ...

  • Page 16

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 16 - the machine counts and the solenoid toggles between reject pocket and stacker. Check the two pockets to make sure that banknote are separated equally in both pockets. *note: if th...

  • Page 17

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 17 - 5. Once notes proceed, sensors retrieve value and they are showed on the list. • max: value of tilt shall not over 4. • ave: value of tilt shall not over 2. • qty: value of l shal...

  • Page 18

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 18 - 1. Place a bundle of 50 pcs test notes (denomination: 1usd) on the hopper and pull the hopper guide to fix the size of test note. The machine starts running once it detects notes ...

  • Page 19

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 19 - 4.3.1 sd upgrade before upgrade the sd card. 1. Get a folder with upgrading firmware and database from ma. 2. Put the folder into sd card with the folder name “_sd_upgrade”. *note...

  • Page 20

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 20 - 4.4 calibration mode before calibrating sensors. 1. Highlight the option and press “ ” 2. Use “f1” and “f2” key to adjust the dimension value of calibration paper. Note: dimension...

  • Page 21

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 21 - 4. Close the lid, check if the cal tool is placed properly, no bending. 5. Move cursor to “2.Ver2-[a] dark paper” and double press “ ”. After the screen shows a black arrow beside...

  • Page 22

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 22 - 4. Close the lid, check if the cal tool is placed properly, no bending. 5. Move cursor to “3. Ver2-[b] bright paper” and double press “ ”. After the screen shows a black arrow bes...

  • Page 23

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 23 - *note: initialization shall only be executed with indication from ma. 1. Press the “ ” key for the initialization and the display shows “wait…”. Do not touch any button and wait u...

  • Page 24

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 24 - 2. Once a ir sensor is covered, the curve on the display reacts. Users may use hand or supporting items to cover sensors and test the status of ir sensors. 3. The following are th...

  • Page 25

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 25 - 4.5.4 calibraiton of hopper sensor to calibrate the ir hopper sensor. 1. Highlight the option and press “ ” to enter the burn in mode. 2. Press “ ” to calibrate the hopper sensor....

  • Page 26

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 26 - 4.6.2 machine running status testing the machine for basic running status under different speeds. 1. Set a preferred speed for testing the device. 2. Different speed can be set by...

  • Page 27

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 27 - 4.6.3 test lcd testing the functionality of lcd display. 1. Highlight the option and press “ ” key. 2. The display shows red , green and blue continually, then it goes back to the...

  • Page 28

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 28 - 4.6.13 test encoder testing the functionality of encoder. 1. Highlight the option and press “ ” key. The motor starts running a certain time. 2. A number of encoder is shown on th...

  • Page 29

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 29 - 0: sd card is not inserted. 1: sd card is detected. 2: sd card is not detected well. * in case of 2, please check if the sd card is completely inserted. 4.7 machinery info to look...

  • Page 30

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 30 - *note: it’s suggested to use default setting on the device. 4.8.1 capacity of pockets to change the default capacity of pockets. 1. To change the maximum capacity of banknote for ...

  • Page 31

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 31 - 4.8.3 detection level 1. Highlight the “count mode-light intensity” and change the level of intensity 0(low) to 3(high) in count mode by pressing “ ”. Note: it’s suggested to use ...

  • Page 32

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 32 - chapter 5 nc-6000 part list and disassembly 5.1 tool preparation screwdriver (+) screwdriver (-) long nose plier 7 mm wrench 3 mm hex key 1.5 mm hex key.

  • Page 33

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 33 - 5.2 housing no part name accessory code picture q’ty 1 top cover-one 3pp02100130041 1 paper-guide (holder) 3pp52500100170 1 paper-guide-l 3ge40008171010 1 paper-guide-r 3ge4000817...

  • Page 34

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 34 - 2 banknote guide- l 3pp92110100010 1 banknote guide- r 3pp92110100020 1 3 side panel l 3pp32100040060 1 4 side panel r 3pp42100040060 1 5 back cover 3pp12100040010 1 6 lid back-fr...

  • Page 35

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 35 - 5.2.1 side panel left and right 1. Prepare the machine and all the necessary tools. 2. Turn the machine to rear side and loosen the two screws (m3x5-countersunk) on right hand. 3....

  • Page 36

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 36 - 5. Disassemble the side panel-r from the machine. *note: when assembling the side cover, please make sure the plastic cover and metal plate fitted to each other. 6. Repeat the ste...

  • Page 37

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 37 - 5.2.3 lid back-frame 1. Loosen the two screws (m3x5-countersunk) on the lid back-frame of right sides. 2. Loosen the another two screws (m3x5-countersunk) on the left side. *note:...

  • Page 38

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 38 - 2. Disassemble back cover from the machine..

  • Page 39

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 39 - 5.3 total assembly.

  • Page 40

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 40 - 5.3.1 upper bill path module no. Part number part name in english picture unit 1 3tp00012030011 feed shaft (12) 1 3nc51500120010 feed bk frame 1 3sc00040100200 m4x10-round head (w...

  • Page 41

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 41 - 3nc00800120020 top frame 1 3tp20000030020 feed adjustment fixed 1 3sc00030100200 m3x10-round head (w/ spring washer) 2 3sp31140210010 compression adjustment (1.4-21) 1 3tp20000030...

  • Page 42

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 42 - 3rpa3100220010 retarding wheel 2 3sc86030061000 m3x6 hex socket set screw (nyloc) 5 3pp52600100180 feed idler wheel arm holder 1 3tp00005030030 metal idler wheel 1 3tp19916010000 ...

  • Page 43

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 43 - sc30006m05nw00 m3x6-round head (w/ spring washer) 1 4 s-bnc6000a06 nc6000-m134 1 3sc52030050200 Ø3×5-pan 4 5 3pp02500100051 upper bill path plate 1 3pp82400000140 led lens (top as...

  • Page 44

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 44 - 3sc02030080200 Ø3×8-round head 7.

  • Page 45

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 45 - 1. Turn the machine to left side and find the two encoders. 2. Loosen the two screws (m4x6-round head with spring washer) on the encoder. *note1: take off the encoder before proce...

  • Page 46

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 46 - 4. Turn the machine to the left side and release the cable from the cable clamp. 5. Disconnect the two cables which are connected to the pcb-motor board. 6. Turn the machine to th...

  • Page 47

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 47 - 5.3.1.1 upper bill path plate 1. Turn the upper bill path module and have the sensor side down. 2. Loosen the three screws (Ø3x8-round head) to release the ground cables. 3. Loose...

  • Page 48

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 48 - 5.3.1.2 pcb nc6100-s board 1. Release the cables from the connecters. *note: when plugging in the cable on the connecters, please make sure all the pins are well connected on the ...

  • Page 49

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 49 - 2. The led len is under the nc6100-irte board. 5.3.1.4 pcb nc6000-m134 board 1. Loosen the four screws (Ø3×5-pan) on the nc6000-m134 board. 2. The nc6000-m134 board is now free to...

  • Page 50

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 50 - 2. Use a 3mm hex key to loosen the two hex flange (m4×10) 3. Use a 1.5mm hex key to release the screw on the retarding wheel spacer. *note: when assembling the singler spacer, ple...

  • Page 51

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 51 - 5. Remove the bearing from the retarding wheel shaft. 6. The retarding wheel is now free to be removed from the module..

  • Page 52

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 52 - 5.3.2 control panel module no. Part number part name in english picture unit 1 3pp02100130030 top front 1 3sc16030050200 m3x5-countersunk 4 2 s-bnc6000a10 nc6000-irr 1 3pp72100000...

  • Page 53

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 53 - 3 3pp72000080150 front panel 1 3sc02030080200 Ø3×8-round head 2 4 c-l00010 tft lcd panel 1 5 3nc90800120050 lcd holder 1 6 3pp62000080140 14 rubber button 1 3pp62000080170 5 rubbe...

  • Page 54

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 54 - 3st4nc6000g010 metal dome 5 key 1 3sc02030080200 Ø3×8-round head 2 3sc52030050200 Ø3×5-pan 4.

  • Page 55

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 55 - 1. Loosen the two screws (m3x5-countersunk) on the control panel module. 2. Loosen the screws (m3x5-countersunk) on the both sides of the hopper. 3. Release the ground cable by lo...

  • Page 56

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 56 - 3. The control panel assembly is now free to be removed. 4. Turn the control panel to the rear side. 5. Loosen the four screws (Ø3x5-pan) on the nc6100-ui board. 6. Loosen the scr...

  • Page 57

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 57 - 2. The left and right keypad is now removed. 5.3.2.3 lcd display 1. Pull out the lcd display from the control panel. 2. The lcd display and lcd holder are removed from the control...

  • Page 58

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 58 - 5.3.3 stacker module no. Part number part name in english picture unit 1 3pp72100130130 outlet part 2 1 3pp82400000080 led (outlet part 2) 1 3pp82100000020 reject sensor light gui...

  • Page 59

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 59 - 3pp92400020120 reject stopper 1 3sp00050080010 torsion reject (0.5-Ø2.7) 2 3tp00002030010 reject shaft (2) 2 3 3pp72100130140 outlet part 1 1 3oc25390000000 static brush 3 3nc9060...

  • Page 60

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 60 - 1. Lay down the machine and loosen the four screws (Ø3x8-countersunk) on the bottom of the machine. 2. Release the stacker stopper and stacker static plate from the stacker module...

  • Page 61

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 61 - 5.3.3.1 stacker and reject pocket 1. Loosen the two screws (Ø3x8-countersunk) ob the both sides of the stacker module. 2. Release the reject pocket plate from the assembly. 3. The...

  • Page 62

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 62 - 5.3.4 bottom conveyor module no. Part number part name in english picture unit 1 3pp12100130020 back lid 1 2 3pp22500100031 bottom conveyor plate 1 3tp00007030010 idler wheel shaf...

  • Page 63

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 63 - 3rpa3120220070 idler wheel(5-6-35) 3 3wa60500217000 e-ring (Ø5) 10 3sp02060030010 torsion idler (0.6-Ø6.8) 6 3ppa2600100110 idler fixed 6 3sc02030080200 Ø3×8-round head 6 3pp62100...

  • Page 64

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 64 - 1. Open the back lid. 2. Release the back lid connector from the back lid. 3. Release the e-ring (Ø4) from the both side of shaft 4. The back lid is now removed. 5.3.4.1 bottom co...

  • Page 65

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 65 - 2. Disconnect the indicated cable from the connector. 3. Pull out slowly the bottom conveyor plate. *note: if it results dificulty when pulling out the bottom conveyor plate, plea...

  • Page 66

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 66 - 5.3.5 base module no. Part number part name in english picture unit 1 ospsolrsa32470 solenoid 1 3nc50800120121 solenoid cover 1 3pp62500100160 note toggler 1.

  • Page 67

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 67 - 3tp00306130010 interrupter bar 1 3ppa2600100120 shaft sleeve (interrupter) 1 3nc60800120030 interrupter plate 1 3sc36030060200 m3×6-round washer 2 sc30006m05nw00 m3x6--rround head...

  • Page 68

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 68 - 3sc52030050200 Ø3×5-pan (ph#2) 1 3sc00030100200 m3x10-round head w/ spring washer (ph#2) 2 6 3nca0300190010 encoder wheel 2 3sc00040060200 m4x6-round head w/ spring washer 2 7 3tp...

  • Page 69

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 69 - 3rpa3100220040 singler wheel - driver 1 3wa41050917000 wave washer (Ø10.5) 1 3wa01040209000 flat washer (Ø10.4×Ø21×1.5t) 1 3ppa2600100130 singler wheel fixer 1 9 s-bnc6000a11 nc60...

  • Page 70

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 70 - 3sc00030100200 m3x10-round head (w/ spring washer) 4 11 3nc20800120060 power bk 1 ed000003f002 ac socket emi filter 1 c05mh03nn125 harness - ac_in 1 c-f00003 fan 1 3sc12040120200 ...

  • Page 71

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 71 - 13 3lb0s20m160000 timing belt (160-s2mx6mm) 1 14 3lb0s30m189000 timing belt (189-s3mx6mm) 1.

  • Page 72

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 72 - 5.3.5.1 timing belts 1. Turing the gear (a) and pulling out the timing belt from the gear (b) to release the timing belt 160mm-s2m. 2. Use the same way as the first step to releas...

  • Page 73

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 73 - 2. The reject pocket holder is now removed from the machine. 5.3.5.3 note toggler 1. Loosen the screw (m3×6-round washer) on the solenoid interrupter plate and it’s free to be rem...

  • Page 74

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 74 - 5. Pull out the solenoid to remove it from the machine. 6. Release the plastic e-ring and the bearing from the shaft. 7. The note toggler is now free to be removed from the machin...

  • Page 75

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 75 - 2. Release the bearing (688zz) from the shaft of kicker roller module. 3. The kicker roller module is now free to be removed. 5.3.5.5 pcb nc6000-dte board 1. Loosen the screw (m3x...

  • Page 76

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 76 - 3. Release the cable from the connector. 4. The bill path is now removed from the machine. 5. Loosen the two screws (m3x10-round head with spring washer) on the nc6000-dte board. ...

  • Page 77

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 77 - 5.3.5.6 pcb nc6000-irtr2 board and ir guide box 1. Loosen the four screws (m3x10-round head with spring washer) on the nc6000-irtr2 board. 2. The nc6000-irte2 board is now free to...

  • Page 78

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 78 - 5.3.5.9 pcb nc6000-a board 1. The nc6000-a board is on the left side of the machine. 2. Disconnect the cables from the nc6000-a board. *note: the following are the positions of ca...

  • Page 79

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 79 - 5.3.5.10 pcb nc6000-motor board 1. The nc6000-motor board is on the left side of the machine 2. Disconnect the cables from the nc6000-motor board. *note: the following are the pos...

  • Page 80

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 80 - 5.3.5.11 power tray 1. Loosen the two screws (m3x5-countersunk)on the power tray 2. Pull out the power tray from the machine. *note: please organize the cable on the correct posit...

  • Page 81

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 81 - 2. Release the motor cover from the machine. 3. Loosen the three screws (m3x6-round head w/ spring washer) of the motor. 4. The two motors are new free to be removed from the mach...

  • Page 82

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 82 - 3. Loosen the two screws (m3x6-round head w/ spring washer). 4. The impeller is now removed from the machine..

  • Page 83

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 83 - chapter 6 trouble shooting 6.1 definition of message codes 6.1.1 check bill path 6.1.2 open bill path 6.1.3 remove banknotes  please open the bill path and check no foreign matte...

  • Page 84

    Service manual – nc-6000 date: oct 1 st , 2012 (version 1.0) masterwork automodules tech. Corp., ltd confidential - 84 - 6.1.4 error  the stacker is full. Please remove the banknotes from the stacker.  the counted quantity doesn’t reach preset number. Please check again.  please check if the moto...