Summary of mr5mk2
Page 1
O w n e r ’ s m a n u a l high resolution powered studio monitor mr5mk2.
Page 2
2 mr5mk2 mr5mk2 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. ...
Page 3: Contents
Part no. Sw0893 rev. B 05/11 ©2011 loud technologies inc. All rights reserved. 3 owner’s manual owner’ s manual don’t forget to visit our website at www.Mackie.Com for more information about this and other mackie products. Important safety instructions ..................................................
Page 4: Introduction
4 mr5mk2 mr5mk2 introduction • in addition, the amplifiers’ gain and frequency responses are individually hand-trimmed to compensate for typical manufacturing tolerances between the drivers and produce a smooth frequency response from 50 hz to 20 khz. • the connecting wires between the amplifier out...
Page 5: Quick Start
5 owner’s manual owner’ s manual quick start we realize that you can’t wait to hook up your new mackie mr5mk2 studio monitors and try them out. Nevertheless, please take the time to read this page now, and the rest can wait until you’re good and ready. 1. Turn the input level [2] control on the back...
Page 6: Rear Panel Description
6 mr5mk2 mr5mk2 rear panel description 2. Input level the mr5mk2 expects a line-level signal at its input. Use this control to adjust the sensitivity of the input section according to the signal strength at its input. • the mr5mk2 is designed to operate with a +4 dbu sig - nal when the input level c...
Page 7: Front Panel Description
7 owner’s manual owner’ s manual 5. Power switch switch up to turn the mr5mk2 on. Make sure the level control is down before you turn it on. When the power switch is turned on and the mr5mk2 is plugged into an ac outlet, the power led on the front of the monitor lights up to let you know the mr5mk2 ...
Page 8: Protection Circuits
8 mr5mk2 mr5mk2 protection circuits input signal wiring you should use high-quality, shielded cable to connect the signal source to the signal input jack [1] on the mr5mk2. • for balanced signals, foil shielded cables, such as belden 8451, 8761, or 9501 are commonly used for studio wiring. • microph...
Page 9: No Sound
9 owner’s manual owner’ s manual appendix a: service information no sound • is the power indicator [8] on the front panel illuminated? If not, refer to “no power” above. • is the input level [2] control turned up? • is the signal source turned up? Make sure the signal level from the mixing console (...
Page 10: Repair
10 mr5mk2 mr5mk2 repair for warranty service, please refer to the warranty information on page 15. Non-warranty service for mackie products is available at a factory-authorized service center. To locate your nearest service center, visit www.Mackie.Com, click “support” and select “locate a service c...
Page 11: Xlr Connectors
11 owner’s manual owner’ s manual xlr connectors xlr connectors are used to make balanced connections to the mr5mk2. They are wired as follows, according to standards specified by the aes (audio engineering society). Xlr hot (+) pin 2 cold (–)pin 3 shield (ground) pin 1 1/4" trs phone plugs and jack...
Page 12: Mr5Mk2 Specifications
12 mr5mk2 mr5mk2 appendix c: technical information ac power requirements us: 120 vac, 60 hz europe: 240 vac, 50 hz korea: 220 vac, 60 hz japan: 100 vac, 50/60 hz note: the mr5mk2 does not support multiple voltage configurations. Make sure the voltage rating for your particular model (as indicated on...
Page 13: Mr5Mk2 Block Diagram
13 owner’s manual owner’ s manual the following are trademarks or registered trademarks of loud technologies inc.: the mackie logo, mr series and the running man. This manual also contains names and marks of other companies which belong to those respective companies, and are hereby acknowledged. Mr5...
Page 14
14 mr5mk2 mr5mk2 low freq filter high freq filter 0 –2db +2db +2db +4db caution: replace with the same fuse and rating. Disconnect supply cord before changing fuse. (normal) 0 (normal) level input off max this device complies with part 15 of the fcc rules for the u.S. And ices-003, for canada. Opera...
Page 15: Mackie Limited Warranty
15 owner’s manual owner’ s manual mackie limited warranty please keep your sales receipt in a safe place. This limited product warranty (“product warranty”) is provided by loud technologies inc. (“loud”) and is applicable to products purchased in the united states or canada through a loud-authorized...
Page 16
16220 wood-red road ne • woodinville, wa 98072 • usa united states and canada: 800.898.3211 europe, asia, central and south america: 425.487.4333 middle east and africa: 31.20.654.4000 fax: 425.487.4337 • www.Mackie.Com e-mail: sales@mackie.Com.