Summary of M80
Page 1
Portable electric wall chasers wall chasers original user guide made in spain.
Page 2: Portable
2 portable electric wall chaser macroza sscc200 macroza m80 macroza m95.
Page 3
3.
Page 4
G geenneerraall ssaaffeettyy rruulleess 1. Keep your work area clean, tidy and well lit. Dirty, untidy and dark work areas increase the risk of accidents. 2. Do not operate your macroza wall chaser in explosive atmospheres such as in the presence of flammable liquids or gasses. Power tools create sp...
Page 5
12. Do not overreach. Keep a proper footing balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Follow instructions in this book of proper chasing positions. 13. Store idle your macroza wall chaser in a dry safe place under lock and key and o...
Page 6
Electrical safety the installation voltage must be as stated on the macroza wall chasers’ specifications plate warning! To reduce risk of injury, end-user must read instruction manual carefully. Equipment description 1. On/off switch 2. Rear handle 3. Motor casing 4. Front handle/milling cutter cove...
Page 7
7 “direction of thrust” “support the shaft on the casing fixed spanner” installing the milling cutter • there are several sizes of macroza milling cutter depending on desired width and depth of the chase. • only original macroza milling cutters should be used as they are specifically designed for ma...
Page 8
8 figure. 5 figure. 4 “correct” “left hand incorrect” vertical chases • vertical chases are done from top to bottom. • right hand should hold on to handle and switch while the left hand firmly grips on the milling cutter cover (figure 5). • left hand guides the chaser machine bearing most of the for...
Page 9
9 figure. 6 figura. 7 horizontal chases • horizontal chases are done from right to left. • the right hand holds the wall chaser by the right side of the milling cutter cover and pushes leftwards (figure 6). • right arm will lean on to the machine and push also leftward from the left hand side (figur...
Page 10
10 horizontal chases close to the floor • horizontal chases close to the floor are done from left to right. (figure 8) • right hand holds the machine by the rear handle and operates the switch. Left hand holds the milling cutter cover from the left hand side and pushes to the right (figure 8) overlo...
Page 11
11 dust collection option for macroza m95 & sc200 macroza m95 and sc200 come with optional dust collection outlet if needed. • remove milling cutter cover cap as shown on figure 9 • insert dust collector adaptor. Figure 10 • attach dust collector adaptor on dust collection system as shown on figure ...
Page 12
Macroza wall chasers’ cutting device is a tungsten carbide tipped milling cutter. There are seven different types of milling cutters depending on required cutting measure (depth x width): 12 notes cutting width and depth might vary depending on milling cutter’s level of wear. • for cuts wider than 5...
Page 13
Milling cutter sharpening use the macroza carbide tester before sharpening the milling cutter to check whether the carbide teeth need to be sharpened. “do not use this kind of machine for sharpening.”.” “sharpening must be done with this kind of grinding stone machine.” sharpening must be carried ou...
Page 14
Only the milling cutter upper side should be sharpened. Do not sharpen the front part. Milling cutter perfromance table macroza wall chasers machine has been designed to work on the following materials: do not use the macroza chaser machines on concrete, pre-cast concrete, stone or any other extreme...
Page 15
15 milling cutter tungsten plate replacement keep your milling cutter sharpened at all times and without any missing tungsten carbide plate. A milling cutter with a missing or broken tungsten carbide plate will be useless within a few hours of work and may be a potential hazard. Repair immediately. ...
Page 16: Ón
E0 2 fa n e0 3 fa n sp ac er e0 8 ca rb on b ru sh e0 9 br us h pl ug e1 1 br us h ho ld er tu be e1 4 in su la te d so ck et e1 5 sw itc h e1 7 ca pa cit or e1 9 sw itc h in su la to r e2 1 ru bb er c ab le b us hi ng e2 2 ca bl e w ith p lu g (3 m .) e2 5 bo tto m c as e in su la to r e3 01 ar m a...
Page 17
17.
Page 18: Ón
E0 2 fa n e0 3 fa n sp ac er e0 6 st at or in su la tio n tu be e0 8 ca rb on b ru sh e0 9 br us h pl ug e1 1 br us h ho ld er tu be e1 4 in su la te d so ck et e1 5 sw itc h e1 6 pr ot ec tio n ch ip e1 7 ca pa cit or e1 9 sw itc h in su la to r e2 1 ru bb er c ab le b us hi ng e2 2 ca bl e w ith p...
Page 19
19.
Page 20: Ón
E0 1 ar m at ur e e0 2 fa n e0 3 fa n sp ac er e0 4 st at or e0 6 st at or in su la tio n tu be e0 8 ca rb on b ru sh e0 9 br us h pl ug e1 1 br us h ho ld er tu be e1 4 in su la te d so ck et e1 5 sw itc h e1 6 pr ot ec tio n ch ip e1 7 ca pa cit or e1 9 sw itc h in su la to r e2 1 ru bb er c ab le...
Page 21
21.
Page 22: Macroza M80
22 angel fernandez responsable de calidad ec declaration of conformity (2006/42/ce) the company macro s.L., wall chaser machines manufacturer with official address at: calle leñeros, 15 - 28039 madrid - (spain) declares under its own responsibility that the portable wall chaser machine: brand: macro...
Page 23: Macroza M95
Ec declaration of conformity (2006/42/ce) the company macro s.L., wall chaser machines manufacturer with official address at: calle leñeros, 15 - 28039 madrid - (spain) declares under its own responsibility that the portable wall chaser machine: brand: macroza model: m95 voltage: 110v / 130v a.C. ó ...
Page 24: Macroza Sc200
24 ec declaration of conformity (2006/42/ce) the company macroza s.L., wall chaser machines manufacturer with official address at: calle leñeros, 15 - 28039 madrid - (spain) declares under its own responsibility that the portable wall chaser machine: brand: macroza model: sc200 voltage: 110 v / 130v...