- DL manuals
- MACROZA
- Power Tool
- SC 100
- Instructions For Use And Maintenance Manual
MACROZA SC 100 Instructions For Use And Maintenance Manual
Summary of SC 100
Page 1
Instructions instructions for use and maintenance made in spain sc100 “portable electrical chaser machine”.
Page 2: General Safety Rules
The term “power tool”, “machine”, and “chaser machine” in all warnings below refers to mains- operated macroza sc-100 wall chaser. 1. Keep your work area clean, tidy and well lit. Dirty, untidy and dark work areas increase the risk of accidents. 2. Do not operate macroza sc-100 in explosive atmosphe...
Page 3
3 12. Do not overreach. Keep a proper footing balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Follow instructions in this book of proper chasing positions. 13. Store idle macroza sc-100 in a dry safe place under lock and key and out of re...
Page 4
Warning! To reduce risk of injury, user must read instruction manual. Electrical safety the installation voltage must be as stated on the macroza sc-100 specifications plate equipment 1 macroza sc-100 chaser machine 1 special fixed wrench for loosening the milling cutter 1 fixed spanner for tighteni...
Page 5
5 starting job with macroza sc100 • plug macroza sc-100 in the mains socket. • switch on macroza sc-100 before contact with the surface to verify its rotating direction. Teeth must rotate forward as shown in figure 1. • lean macroza sc-100 lateral to the wall. Slowly insert the milling cutter into t...
Page 6
6 horizontal chases • horizontal chases are done from right to left. • the right hand holds the wall chaser by the right side of the milling cutter cover and pushes leftwards (figure 6). • right arm will lean on to the machine and push also leftward from the left hand side (figure 7). • the left han...
Page 7: Milling Cutters
7 the macroza sc100 chaser machine’s cutting attachment is a widia-tipped (carbide tungsten) milling cutter. It is used with seven different types of milling cutters depending on the measure of chase required (depth x width): notes: cut width and depth might vary depending on milling cutter’s level ...
Page 8
Afilado de la fresa antes de afilar la fresa, emplearemos el comprobador de afilado para verificar si sus dientes necesitan ser afilados. Comprobador de afilado do not use this kind of machine for sharpening. Carbide sharpness tester 8 sharpening must be done with this grinding stone..
Page 9
Installing the milling cutter • there are several sizes of macroza milling cutter depending on the width and depth of the chase. • only original macroza milling cutters should be used as they are designed specifically for the macroza sc-100. • make sure that the macroza sc-100 is switched off and un...
Page 10
To sharpen a milling cutter use an emery or grinding stone with the following specifications: carborundum, grain 80, and grade jk. Milling cutter sharpening angle must be 5° (cutting angle a), as shown in figure 9. Aproximate milling cutter duration the macroza sc100 chaser machine has been designed...
Page 11
11 repairing the milling cutter (plate replacement): keep your milling cutter sharpened at all times and without any missing carbide widia tooth. A milling cutter with a missing or broken widia tooth will be useless within a few hours of work and may be a potential hazard. Repair immediately. Widia ...
Page 12: Ref.
S11 milling cutter cover s12 motor casing x13 intermediate cover x14 complete rear handle s15 switch cover (handle) x16 intermediate cover seal x18 front skid x20 coil isolation cap 21 cutter attachment shaft 23 cutter attachment washer 24 shaft dust-guard 25 shaft grease retainer x26 shaft cover se...
Page 13: Ref.
47 o-ring 48 motor bearing cover 49 casing lower insulator 50 interior insulator s51 complete armature s52 stator 53-54 fan spacer & fan s58 auto switch-off brush 59 brush plug s61 brush tube 62 insulated bushing m65 switch 66 cable exit rubber grommet 67 cable with mains plug ref. Descripción 69 ca...