Macurco CM-6 User instructions - page 10
10
the second selection “PUt” or Power Up Test setting. Push Enter. If the testis “On” push Next to turn it “OFF”
(flashing) then push Enter to confirm the change (solid) and push Enter again to return to “PUt” in the Con
menu. Push Nextuntil “End” is displayed then push Enter to get back to normal operation.
Selecting Display Option – “dSP”
To select the Display Configuration, in normal mode, push the Next button to get to “Con” or the Configuration
menu. Then push the Enter button to enter the Con menu. Then push the Next button to get to the third
selection “dSP” or Display setting. Push Enter. If the display is “On” push Next to turn it “OFF” (flashing) then
push Enter to confirm the change (solid) and push Enter again to return to “dSP” in the Con menu. Push Next
until “End” is displayed then push Enter to get back to normal operation.
Selecting Buzzer Option – “bUZ”
To select the Buzzer Configuration, in normal mode, push the Next button to get to “Con” or the Configuration
menu. Then push the Enter button to enter the Con menu. The forth selection is the “bUZ” or Buzzer setting.
Push Next twice to get to “bUZ” then Enter. If the display is “On” push Next to turn it “OFF” (flashing) then push
Enter to confirm the change (solid) and push Enter again to return to “bUZ” in the Con menu. Push Nextuntil
“End” is displayed then push Enter to get back to normal operation.
Selecting Alarm Relay Setting – “ArS”
To select the Alarm Relay Setting, in normal mode, push the Next button to get to “Con” or the Configuration
menu. Then push the Enter button to enter the Con menu. The fifth selection is the “ArS” or Alarm Relay
Setting. Push Next three times to get to “ArS” then Enter. If the display is “OFF” (disabled) push Next to
change it to 50, 100, 150 or 200 ppm (flashing) then push Enter to confirm the change (solid) and push Enter
again to return to “ArS” in the Con menu. Push Nextuntil “End” is displayed then push Enter to get back to
normal operation.
Selecting Alarm Relay Configuration – “Arc”
To select the Alarm Relay Configuration, in normal mode, push the Next button to get to “Con” or the
Configuration menu. Then push the Enter button to enter the Con menu. The sixth selection is the “Arc” or
Alarm Relay Configuration. Push Next four times to get to “Arc” then Enter. If the relay is “nO” (normally open)
push Next to turn it to “nC” (flashing) then push Enter to confirm the change (solid) and push Enter again to
return to “Arc” in the Con menu. Push Nextuntil “End” is displayed then push Enter to get back to normal
operation.
Selecting Fan Relay Settings – “FrS”
To select the Fan Relay setting, in normal mode, push the Next button to get to “Con” or the Configuration
menu. Then push the Enter button to enter the Con menu. The seventh selection is the “FrS” or Fan Relay
setting. Push Next five times to get to “FrS” then Enter. If the fan relay is “OFF” (disabled) push Next to change
it to 25, 35, 50 or 100 ppm (flashing) then push Enter to confirm the change (solid) and push Enter again to
return to “run” in the Con menu. Push Nextuntil “End” is displayed then push Enter to get back to normal
operation.
Selecting Fan Relay Delay – “FrD”
To select the Fan Relay Delay setting, in normal mode, push the Next button to get to “Con” or the
Configuration menu. Then push the Enter button to enter the Con menu. The eighth selection is the “FrD” or
Fan Relay Delay. Push Next six times to get to “FrD” then Enter. If the delay is “OFF” (disabled) push Next to
change it to 1, 3, 5, or 10 minutes (flashing) then push Enter to confirm the change (solid) and push Enter
again to return to “FrD” in the Con menu. Push Nextuntil “End” is displayed then push Enter to get back to
normal operation.