- DL manuals
- MadgeTech
- GPS
- RFPulse2000A
- User Manual
MadgeTech RFPulse2000A User Manual
Summary of RFPulse2000A
Page 2: Product User Guide
Product user guide rfpulse2000a data logger quick start steps ........................................... 1 product overview .......................................... 2 additional features & operation .................... 3 mounting instructions ................................... 4 product mainten...
Page 3: Quick Start Steps
1 1. Install the madgetech 4 software and usb drivers onto a windows pc. 2. The rfc1000 interface device comes with a usb cable. Plug one end of the cable into an available usb port on the pc and plug the opposite end of the cable into the communication port on the rfc1000. 3. Push and hold the wire...
Page 4: Product User Guide
Product user guide product overview the rfpulse2000a is a wireless data logger that records pulse output signals from various sensors such as flow meters and anemometers. When started, the data logger samples at 100hz and at the user specified reading rate. The rfpulse2000a features a display screen...
Page 5: Rfpulse2000A
Rfpulse2000a additional features and operation alarm settings/rules in madgetech 4, alarms can be created on two levels; in the software itself, and programmed specifically to the data logger. Creating alarm rules in the software allows the user to utilize alarms while real time recording, and have ...
Page 6: Product User Guide
Product user guide the base provided with the rfpulse2000a can be used in two ways. • the bottom of the logger snaps in place to use and mount the unit on a table top or horizontal surface. • the base can also securely snap to the backside of the logger for wall mounting if desired (as shown below)....
Page 7: Rfpulse2000A
Rfpulse2000a product maintenance battery replacement materials: u9vl-j battery 1. On the bottom of the enclosure, open the battery compartment by pulling in on the cover tab. 2. Remove the battery by pulling it from the compartment. 3. Install the new battery, taking note of the polarity. 4. Push th...
Page 8: Product User Guide
Product user guide reading rate 1 reading every second up to 1 reading every 24 hours memory 16,128 readings led functionality • green led blinks every 5 seconds to indicate unit is logging • blue led blinks every 15 seconds to indicate unit is in wireless mode • red led blinks every 1 second to ind...
Page 9: Rfpulse2000A
Rfpulse2000a sensor type channel 1: ambient; pulse detection circuit channel 2: mathematic; phantom total channel response time 10 microseconds input range 0 to 4,294,967,295 pulses rf frequency 2.45ghz ieee 802.15.4 ultra-low power madgenet wireless transceiver with fully bi-directional communicati...
Page 11: Rfc1000
Rfc1000 product overview madgetech has designed the rfc1000, a high powered transceiver that has a substantially long transmission range, providing enhanced performance in occluded environments (ovens, refrigerators, etc.). The rfc1000 also features an external antenna, allowing more flexibility wit...
Page 12: Product User Guide
Product user guide mounting instructions for best wireless performance, both the rfc1000 and the madgetech data loggers should be mounted in the same orientation. This usually means that the external antenna should be pointing straight up. The antenna can pivot to accommodate either a wall mount or ...
Page 13: Rfc1000
Rfc1000 channel 11 channel 12 channel 13 channel 14 channel 15 channel 16 channel 17 channel 18 channel 19 channel 20 channel 21 channel 22 channel 23 channel 24 channel 25 channel 26 (not supported) channel programming the rfc1000 transmits data on the 2.4ghz band and is programmed by default on ch...
Page 14: Product User Guide
Product user guide rfpulse2000a: to program the channel on the rfpulse2000a data logger, start by switching the wireless mode to off by holding down the wireless button on the data logger for 5 seconds. Step 1: use the usb cable, plug the usb end of the cable into an available usb port on the pc. St...
Page 15: Rfc1000
Rfc1000 • “this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” • “to satisf...
Page 16: Troubleshooting Tips
Troubleshooting tips why is the wireless data logger not appearing in the software? If the rfpulse2000a doesn’t appear in the connected devices panel, or an error message is received while using the rfpulse2000a, try the following: • check that the rfc1000 is properly connected. For more information...