Magenta MultiView II AK600 Quick Start Manual - page 3
© 1998-2012 by Magenta Research, LTD., All rights reserved.
Magenta Research, LTD, 128 Litchfield Road New Milford, CT 06776 USA
USA: (800) 805-0944
INT: (+1) 860-210-0546
www.magenta-research.com
Document # 5310269-01 Rev-01 (10/8/2012)
Page 3 of 4
Configuration Mode-1, 4
th
Pair Options:
The MVII-AK600 provides several options for using the 4
th
-pair signals (pairs 1-3 are
generally used for video). The factory-default settings support analog audio (L+R summed) on the 4
th
-pair. Note that the connected
MultiView transmitter and any daisy-chained receivers must be configured with a matching 4
th
-pair operating mode. Otherwise, the
desired 4
th
-pair signal will not work as expected
– but the video will not be affected.
(starting in normal-mode)
Press and hold the CFG button until the CFG indictor is ON. Release the CFG button.
o
LEDs 1-8 will show the current value for all Mode-1 configuration settings as bright/off.
Press and release the SKEW/SEL button twice.
LED indicators 4-6 should be illuminated (either DIM or ON); all others (indicators 1-3, 7 and 8) should be off.
Press the UP and DOWN buttons to step through the available 4
th
-pair settings as shown below.
To leave configuration-mode, leave the buttons untouched for 10 seconds or press the CFG button.
LED4
LED5
LED6
Front Panel View
4
th
-pair Operating Mode
dim
dim
dim
(THP: Need new photo.)
If option-module is installed: 4
th
-pair operating mode is defined by the presence
of the option-module (232/SA/SAP) and this setting cannot be changed.
If the option-module is not installed: 4
th
-pair signals are disabled. This effectively
“mutes” anything being sent on the 4
th
pair. This can be useful for diagnostic
purposes.
dim
dim
ON
Direct pass-through of 4
th
-pair wires (custom applications).
dim
ON
dim
External analog (L+R summed) audio
(“-A” mode).
This is the factory-default mode if no daughterboard option is installed.
(Remember to also check 4
th
-pair termination setting)
dim
ON
ON
External S/PDIF digital audio. Output-impedance = 75-ohms.
(Remember to also check 4
th
-pair termination setting)
ON
dim
dim
Simplex-serial
(“-S” mode)
(Remember to also check 4
th
-pair termination setting)
Configuration Mode-1, Vsync Polarity:
The MVII-AK600 provides settings for Vsync polarity: (+) or (-).
(starting in normal mode)
Press and hold the CFG button until the CFG indictor is ON. Release the CFG button.
o
LEDs 1-8 will show the current value for all Mode-1 configuration settings as bright/off.
Press and release the SKEW/SEL button three times.
LED indicator 7 should be illuminated (either DIM or ON); all others (indicators 1-6 and 8) should be off.
Press the UP and DOWN buttons to change Vsync polarity from Positive (bright) to Negative (dim).
To leave configuration-mode, leave the buttons untouched for 10 seconds or press the CFG button.
Note: This setting only has an effect if the sync-
mode is set to “Fixed”.
Configuration Mode-1, Hsync Polarity:
The MVII-AK600 provides settings for Hsync polarity: (+) or (-).
(starting in normal mode)
Press and hold the CFG button until the CFG indictor is ON. Release the CFG button.
o
LEDs 1-8 will show the current value for all Mode-1 configuration settings as bright/off.
Press and release the SKEW/SEL button four times.
LED indicator 8 should be illuminated (either DIM or ON); all others (indicators 1-7) should be off.
Press the UP and DOWN buttons to change Hsync polarity from Positive (bright) to Negative (dim).
To leave configuration-mode, leave the buttons untouched for 10 seconds or press the CFG button.
Note: This setting only has an effect if the sync-
mode is set to “Fixed”.