Summary of M870AS
Page 1
Magicar m870as en car alarm with two-way remote and remote - start system installation guide.
Page 2: English
English en.
Page 3
En table of contents i. Introduction............................................................................................................................ 4 ii. Placing.................................................................................................................................
Page 4: I. Introduction
En i. Introduction magicar m870as is a safety device with the highest level of security. Thanks to the 2-way remote with pager you will be immediately informed about possible car intrusion, as well as the manner of the intrusion even though you are too far from the car to hear the siren. Magicar m87...
Page 5
En warning! ¾ when installing the alarm into a manual transmission car, you must not cut off the remote starting loop located in the alarm control unit. ¾ in case the remote starting loop is cut off, you must reconnect it or install the alarm into an automatic transmission car ¾ in case of an automa...
Page 6: IV. Wiring Arrangement
En 6 if you want to change the signal polarity (-) to (+) 87 30 87a 85 86 +12v output (+) impuls (-) e.G.: when aux is installed, a relevant device is operating on (+). If you want to disconnect two wires by a (-) signal +12v e.G.: with a (-) signal, lines a and b are cut off. Use this when a starte...
Page 7
En connector 3 – cn3 on this connector the complete relay outputs for control of central locking are located. 7 1 – yellow/black - door unlocking relay output (nc) 2 – yellow - common wire (com) of unlocking relay 3 – yellow/white - switch wire (no) of door unlock relay 1 – blue - wire grounded when...
Page 8
En 10 – brown/black - negative hood switch input (-) 11 –black/white - foot brake input reacting on (+) 12 – light blue/black - emergency brake input reacting on (-) 8 - additional outputs connector 5 - red additional outputs controlled by the remote control. For settings see programming menu 2-08, ...
Page 9
En 9 - uart connector 6 - black - antenna connector 7 - blue - temperature sensor connection 8 - blue connector 9 - white - led indication connector 10 - white - rps sensor - shock sensor connector 11 - red 1 – black - grounding 2 – white - shock sensor input – second level (-) - additional sensor 1...
Page 10: VI. Remote Start Loop
En vi. Remote start loop the remote start loop is located under the cover of the main unit of the car alarm: loop cut off: automatic transmission not cut off: manual transmission attention! When the loop is cut off, you can start remotely at anytime. Therefore, the loop can only be disconnected in c...
Page 11
En en programming menu no. 1 when the door is open and ignition is on keep buttons i and ii pressed simultaneously for 2 sec. Options no. Function button i button ii button iii button iv 1-01 turbo mode off 2 min 1 min - 1-02 regular starting off on - - 1-03 engine running time 10 min 25 min 3 min...
Page 12
12 1-13 it allows you to deactivate the ultrasonic sensor port by using remote start function. After cancel remote start the input is activated again. 1-14 this function is available with can bus module. In case you are using read only mode > magicar will only read data from can (trunk, door, hood)....
Page 13
En programming menu reset in case you wish to set all the function back to the pre-set, you can do so by the following way. All the functions will be set to option 1. Procedure: 1. Turn the ignition on and open the door. 2. For resetting the programming menu no.1, keep buttons l+ll pressed for 2 sec...
Page 14: Ix. Valet Mode
En 6. Calibration is successfully completed. Turn the hazard light button off, turn the ignition off and release the brake pedal. 7. Connect the light output wire (cn2-1) to the hazard light switch wire (figure no.1). Check the polarity of common wire cn1-6. After this connection the alarm will cont...
Page 15: Remote Control Programming
En valet mode deactivation. You can deactivate valet mode only by using the remote control: • push together shortly buttons i and iii. • siren will beep once and lights will flash twice. X. Remote controls programming remote control programming 1. Disarmed. 2. Within 3 seconds turn the ignition on/o...
Page 16
En changing pin code pin code is set as the factory default code (11). Pin code must be inserted to enter valet mode after turning key on/off 3 times if you have already selected “pin code on” from optional table. Procedures of change pin code from the factory default code 11 to owner’s own code 1. ...
Page 17
En +12v signal light wire + - + - common wire - + magicar 9 grey/black 8 orange 7 orange/black 6 white 5 white/black 4 red 3 red/black 2 yellow/black 1 blue cn 1 rps sensor shock sensor led signaling output toaccessory output to ignition trunk trigger input (-) output to starter 12v siren fuse 40a p...
Page 18
- the car alarm system is designed for fitting into all kinds of cars with petrol and diesel engines with +12v volatge finished by a negative pole. - car alarm must be fitted following manufacturer‘s recommendation. - the alarm installation to be carried out only by authorised service centre. - cons...