Summary of M9000
Page 1
# installation guide m9000 by youngshin electronics co., ltd. M9000 controllers installation guide m9000 www.Magicar.Com.
Page 2
Table of contents 2 1. Installation tips & recommendations 2. M-9000 wiring digram 3. Cn 1 4. Cn 2 5. Cn 3 6. Cn 4 7. Cn 5 8. Cn 6 9. Cn 7 10. Cn 8 11. Transmitter learning routine 12. Option programming for four button remotes 13. Option programming for six button(one way) remotes 14. Diagnosing pr...
Page 3
4 installation tips & recommendations 3 1-1. Please be careful not to lock yourself out. Please lower the glass windows before you starting the installation in case the door locks with the key inside. Also, learn the remote to the brain module after the installation has been completed. 1-2. Use digi...
Page 4
6 m9000 wiring diagram 5.
Page 5
8 cn1 7 no 1 (white) : (+12v)accessory output this wire will read (using your digital multi-meter) 0v with the key off, and 12v with the key in the accessory or ‘on’ position. The accessory wire will usually drop out during cranking. This wire supplies 12v to climate control and other accessories in...
Page 6
10 cn2 9 no 1, no 2 (violet) : positive signal light output connect this wire to the (+) signal light wire on the vehicle. This wire will read (using your digital multi-meter) either open or ground before the signal light circuit is turned on and then it will read (+)12v after the signal light circu...
Page 7
12 cn3 11 no 5 (white) : (+)12v siren output the black wire at the siren is to be chassis grounded. The siren volume can be reduced by cutting the volume wire attached to the siren. No 6 (black) : (+)12v trunk output if the vehicle is equipped with electrical trunk release, the trunk out is connecte...
Page 8
14 13 no 3 (red/black) : negative trigger door open sense no 4 (red) : positive trigger door open sense please make sure you have found a correct door sensing wire that monitors all doors. +12v cn3-3(-) door trigger dome light door trigger sw door trigger sw +12v cn3-4(+) door trigger dome light b. ...
Page 9
Cn4 cn5 cn6 16 15 no 5 (white/black) : negative glow plug input no 6 (white) : positive glow plug input if you doníft connect one of these wires(negative or positive glow sensing), the system will act as gasoline vehicles. Only when one of these wires are connected, your system will know the diesel ...
Page 10
Transmitter learning routine 18 17 cn7 cn8 no 1 (yellow) : rx no 2 (white) : tx no 3 (red) : (+) no 4 (net wire) : (-) the antenna have been calibrated for horizontal installation at the top corner of the windshield. Different installation may affect the transmitting distance quite seriously. ｝ ante...
Page 11
20 19 2 . Benz types of vehicles that have vacuum hose underneath the ignition key box. ● follow the same steps of the above 1, except that you use button i i i instead of button i . The vehicle has a programming of automatic self-unlock when you turn off the engine with a key. So, in this case you ...
Page 12
22 21 option programming for six button(one way) remotes the procedures will be same as the 4 button remotes except the use of the different buttons. Programming programming menu 1 programming menu 2 option selection factory setting option selection default setting selection 6 button remote (trunk+s...
Page 13
Diagnosing problems with auto-start 23 if there is a problem in auto-starting your car, you will hear three chirps when you attempt to auto-start the car. Wait for 2 seconds and the cause for the error will be indicated by the number of times parking lights flash error number (# of times parking lig...