1. DL manuals
  2. Magicard
  3. Laminator
  4. MAGICARD Sicura Laminator
  5. Quick Start Manual

Magicard MAGICARD Sicura Laminator Quick Start Manual

Manual is about: Ultra Electronics Sicura Laminator Quick Start Guide

Summary of MAGICARD Sicura Laminator

  • Page 1

    Ultra electronics card systems quick start guide magicard sicura laminator page 1 magicard sicura laminator quick start guide laminator setup iss. 09 january 03 3504-22-01 stock no. M9004-593 dcr 27634 refers.

  • Page 2: Setting Up Your

    Quick start guide ultra electronics card systems page 2 magicard sicura laminator setting up your sicura laminator takes just two easy steps: 1. Unpack and install the laminator a preparing a location for the laminator b removing the laminator from the box c check the package contents d install the ...

  • Page 3: Preparing A Location For The

    Ultra electronics card systems quick start guide magicard sicura laminator page 3 location requirements for your laminator/printer: preparing a location for the sicura laminator and printer a • an adequate power supply. • ambient temperature +10 to +30 deg c. • relative humidity 20/70% rh. • protect...

  • Page 4: Removing The Laminator

    Quick start guide ultra electronics card systems page 4 magicard sicura laminator removing the laminator from the box carefully open the box and remove any accessories. Place on a smooth, level surface and remove the polyethylene container. B.

  • Page 5: Checking The

    Ultra electronics card systems quick start guide magicard sicura laminator page 5 checking the package contents c the magicard sicura card laminator envelope containing this quick-start guide a roll of lamination film and a take-up core (only supplied when ordered with the laminator) a power cord wi...

  • Page 6

    Quick start guide ultra electronics card systems page 6 magicard sicura laminator check that the mains supply voltage is correct for your country. (different models are manufactured for each supply voltage.).

  • Page 7: Install The

    Ultra electronics card systems quick start guide magicard sicura laminator page 7 install the lamination film d lift the transparent cover and move the roller lever to the open position. Gently install the roll of film between the rollers. The black alignment marks on the film should be innermost. T...

  • Page 8

    Quick start guide ultra electronics card systems page 8 magicard sicura laminator gently turn both rolls, to ensure that there is no slack film. Close the transparent cover. Replace and fasten the film retaining plate, and close the lever..

  • Page 9: Connect The Laminator

    Ultra electronics card systems quick start guide magicard sicura laminator page 9 connect the laminator to a power supply e check that the laminator operating voltage is correct for your supply voltage. (units cannot be changed from one voltage to another.) check that the temperature controller’s le...

  • Page 10

    Quick start guide ultra electronics card systems page 10 magicard sicura laminator the temperature will achieve the set point level after a delay of 4 minutes, and the ready indicator will illuminate. Notes: 1. When switched on, the laminating roller and take-up roll turn for 30 seconds or until a b...

  • Page 11

    Ultra electronics card systems quick start guide magicard sicura laminator page 11 note: the optimum roller temperature is best determined by trial and error, using your own cards and laminating film. The following notes are for your guidance only. • cards with large, unprinted white areas require a...

  • Page 12

    Quick start guide ultra electronics card systems page 12 magicard sicura laminator insert a card into the slot, side to be laminated uppermost. Cards should be clean, dust-free and not already overcoated. Adjust the in/out position of the laminate on the card by screwing the core in or out, if neces...

  • Page 13

    Ultra electronics card systems quick start guide magicard sicura laminator page 13 adjust the roller temperature for good laminate adhesion as required (up to 200 ° c max). The display normally shows the roller core temperature in ° c. Adjust the setpoint temperature with the ↑ and ↓ keys as desired...

  • Page 14

    Quick start guide ultra electronics card systems page 14 magicard sicura laminator important note for setting up your rio/tango printer driver to work with the sicura laminator – please select the appropriate option in your printer driver for best results. It is necessary to make the correct setting...

  • Page 15

    Ultra electronics card systems quick start guide magicard sicura laminator page 15 note: the rio/tango printer can print cards faster than the sicura can laminate them. There is a hopper capacity of about 12 cards, but to reduce the speed discrepancy, it is recommended that the printer is operated i...

  • Page 16: Printer

    Quick start guide ultra electronics card systems page 16 magicard sicura laminator notes: 1. If the magicard card printer prints a card before the laminator is ready (ie not fully armed up, or still laminating the previous card), the card is held within the body of the printer until the laminator is...

  • Page 17: Stand Alone Mode

    Ultra electronics card systems quick start guide magicard sicura laminator page 17 i operating the hopper/sicura in stand alone mode clip the card feed hopper to the end of the sicura card laminator and remove the card deflection plate. Load the hopper with cards to be laminated (100 cards maximum)....

  • Page 18: Adjusting The Hopper

    Quick start guide ultra electronics card systems page 18 magicard sicura laminator the card feed hopper has been factory set for use with 30 thou cards. Should it require adjustment, carry out the following procedure: adjusting the hopper j remove the hopper from the laminator, remove the interface ...

  • Page 19: Error Indicators

    Ultra electronics card systems quick start guide magicard sicura laminator page 19 the sicura card laminator has three indicators to tell you what is happening: ready (green) - when lit, indicates that it is ready to laminate a card. When flashing, indicates that it is still warming up. When off, ei...

  • Page 20

    Quick start guide ultra electronics card systems page 20 magicard sicura laminator correction operation depends on clean rollers to transport cards, an undamaged laminating roller, and a dust-free environment. It is recommended that the laminator be cleaned after every roll of lamination film (250 c...

  • Page 21: In Case of Difficulty

    Ultra electronics card systems quick start guide magicard sicura laminator page 21 check the installation: • repeat the installation steps in this guide. • check that the laminator mains voltage is correct. • check that the laminating film is the right way round and passes through the optical sensor...

  • Page 22

    Quick start guide ultra electronics card systems page 22 magicard sicura laminator notice the information contained in this document is subject to change without notice. Ultra electronics limited shall not be liable for errors contained herein or for incidental consequential damages in connection wi...

  • Page 23

    Ultra electronics card systems quick start guide magicard sicura laminator page 23 limited warranty information 1) coverage: ultra electronics ltd warrants that the magicard sicura card laminator shipped with this warranty statement will conform to the manufacturers specifications and be free from d...

  • Page 24

    Quick start guide ultra electronics card systems page 24 magicard sicura laminator ec declaration of conformity manufacturer's name: ultra electronics limited. Manufacturer's address: waverley house, hampshire road, granby estate, weymouth, dorset dt4 9xd england. Declares that the products product ...