Summary of Monostick 160i
Page 2
1 contents monostick 160i safety rules 1. Technical information 1.1 general explanations 1.2 components of monostick 160i 1.3 data plate 1.4 technical specifications 1.5 accessorries 2. Installation and operation 2.1 upon receipt and claims 2.2 installing and working recommendations 2.3 connections ...
Page 3
2 monostick 160i identifying safety information these symbols are being used to identify potential risks. When seen a safety symbol in the manual, it must be understood that there is an injury risk and following instructions must be read carefully to avoid potential risks. While welding, keep the th...
Page 4
3 monostick 160i safety rules breathing welding fumes can be hazardous to your health inhaling fumes and gases over a long period of time, generated during welding is dangerous and forbidden . Irritation of the eyes, nose and throat are symptoms of inadequate ventilation. Take immediate steps to imp...
Page 5
4 monostick 160i safety rules noise can damage hearing noise from certain industrial processes or equipments can damage hearing. Wear approved ear protection if noise level is high. Working in small and confined places can be dangerous while welding and cutting in small, confined places, always have...
Page 6
5 monostick 160i safety rules falling unit can cause injury wrong positioned power source or other equipment may cause serious injury to persons or damage to objects. While repositioning the power source always carry by using the lifting eye. Never pull cable, hose or torch. Always carry the gas cyl...
Page 7
1.2 components of monostick 160i technical information 1. Technical information 1.1 general explanations monostick 160i is an inverter type portable, mono-phase dc mma welding machine designed to weld stick electrodes up to 4 mm. This unit can also be used as a dc tig power source for touch-start ap...
Page 8
Technical information 1.3 data plate manual metal arc welding direct current descending characteristics line input-1 phase alternating current appropriate to operate in dangerous work area x :duty cycle* u :open circuit voltage u :line voltage and frequency u :rated welding voltage i :input current ...
Page 9
2.1 upon receipt and claims be sure that you have received all the items that you have ordered. In case of any item is missing or damaged, contact your supplier immediately. In the event of damaged or missing delivery, it to the shipping agency and magma mekatronik with the photocopy of shipping bil...
Page 10
Installation and operation figure 2: tig welding connections diameter of electrode (mm) diameter of nozzle (mm) welding current (a ) dc gas debit (lt/min) 1.0 1.6 6.3 9.5 15 - 70 30 - 150 6 - 8 6 - 8 install the argon gas regulator onto the argon gas cylinder. C gas hose of the torch the regulator o...
Page 11
3.2 nonperiodic maintenance contact tip and nozzle on the torch have to be cleaned regularly and changed if required. Contact tips must be in good condition, longer tips generally give better results. Note: the above recommended maintenence periods are indicative, these may vary according to the wor...
Page 12
Spare parts list appendix 1 upper electronic card middle underside current adjustment potentiometer fan filter card power led - green thermic / error led - red electronic card electronic card power switch designation e201b-03 e201b-02 e201b-01 current 1k m1 e201b-flt led-green power led-red th-err i...
Page 13
Electrical diagram appendix 2 f n earth f n j4 j1 j2 j3 e art h j7 j8 j2 j1 6 p5 j5 p8 2 2 p4 t h 1 - n.O . +7 5° c 1k current led -green power led -red ı t h -e rr t 1 power t ransformer 1 2 earth + - 1 2 p3 s 1 16a e 20 1b -f lt e 20 1b -0 1 e 20 1b -0 3 e 20 1b -0 2 m 1 24vd c 1 2 3 p1 1 2 3 4 p2...
Page 14
+90 236 226 27 00 +90 236 226 27 28 organize sanayi bölgesi 5.K ısım 5503. Sokak no:1 manİsa www.Magmaweld.Com made in tÜrk İye owm 06.21.2011.