1. DL manuals
  2. Magnadyne
  3. Car Alarm
  4. Marksman M4
  5. Installation Manual

Magnadyne Marksman M4 Installation Manual

Other manuals for Marksman M4: Owner's Manual

Summary of Marksman M4

  • Page 1

    For technical assistance (800) 638-3600 for fax on demand technical assistance (800) 994-9977 (must be a registered dealer to use fax on demand system) © copyright 2001 magnadyne corporation installation manual models: m4 m5.

  • Page 2

    Step 1: component installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 step 2: 10-pin main harness installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 step 3: 5-pin power harness installation. . . . . . . . ...

  • Page 3

    First vacant socket: (for use with ala-rpt relay pack only) see optional accessory connection for proper wiring. Gray wire: (pulsed ground for car horn. Applies to m5 only) connect the gray wire to the negative trigger wire on the vehicle’s horn relay. Do not connect the gray wire directly to the ve...

  • Page 4

    Step 3: 5-pin power harness installation the power harness contains 3 wires and two vacant sockets. Follow the wiring recommendations enclosed for each wire. Power harness first socket second socket first vacant socket: (applies to m5 only) the first vacant wire socket is a low current (300ma) groun...

  • Page 5

    3 wire ground trigger door lock system (-) lock out ground input (-) unlock out to door lock control relays to alarm lock control switch black wire: connect to unlock red wire: connect to lock orange wire: no connection 3 pin black plug 5 wire ground at rest door locking systems 87 87a 85 86 30 87 8...

  • Page 6

    Step 4: optional accessory connections (continued) one wire multiplexing door locking systems some vehicle’s (chrysler, mazda, ford,) use one wire to lock and unlock the doors. To properly interface with these one wire systems you must use part # ala-dl1. We have developed patented plug-in fuse resi...

  • Page 7

    Blue wire violet wire to b+ or ground as required white wire no connection brown wire no connection lock fuse 1 unlock fuse 2 black 3-pin housing green wire ala-dl1 to vehicles lock/unlock wire step 4: optional accessory connections (continued) unlock driver's door first wiring for 3-wire positive d...

  • Page 8: Starter Disable Connection

    Step 4: optional accessory connections (continued) starter disable and engine disable using optional ala-rps2 relay pack: using the wiring information to connect the optional starter disable relay as follows: a. Locate the “start only” wire coming from the ignition key switch and cut it. B. Connect ...

  • Page 9: Flashing Lights

    Parking lights only piggyback connection headlight switch red wire with white stripe output from alarm flashing lights step 4: optional accessory connections (continued) starter 87 87a 86 85 30 87 87a 86 85 30 "acc" "start" cut "off" "on" "acc" "start" "off" "on" cut black wire black wire black wire...

  • Page 10

    Step 4: optional accessory connections (continued) white/orange wire optional dome light illumination and lighted pathway illumination (applies to m5 only) output to domelight (+ or - ) input to relay (+ or - ) white/purple wire orange wire purple wire low beam headlights warning! Piggyback connecti...

  • Page 11

    Red wire ala-rpt relay pack orange wire output to trunk switch purple wire input to relay (+ or -) insert red wire into the first socket insert black wire into the eighth socket black wire #2 button power trunk activation using optional ala-rpt relay pack 87 86 85 30 orange wire (spst ala984h relay ...

  • Page 12

    12 step 5: transmitter coding on remote transmitter coding and operation: the supplied transmitters are pre-programmed to the security system alarm module using dedicated buttons mode. Follow the procedures below to add replacement transmitters or to change from dedicated buttons mode to separate ch...

  • Page 13

    Press the lock button 1. The horn/siren chirp 1 time. 2. The led will flash 1 time. 3. The lock button is now programmed. To program additional transmitters at this time, press each transmitters lock button. 4.Flip the valet switch on/off 1 time. Press the unlock button 1.The horn/siren chirp 2 time...

  • Page 14

    14 off on turn on the ignition key flip the valet switch on/off 6 times the led will be on solid. The horn/siren will emit 1 long then 1 short beep) you are now in the “remote feature programming” mode. On “separate channel mode” x6 ☛ step 2 step 3 step 1 step 4 2 1 3 off turn off the ignition the l...

  • Page 15

    15 # button changed function confirmation 3.5 sec. Door lock timing 1-chirp, led parking lights flash 1 lock .8 sec door lock timing (default) 2-chirps, led parking lights flash door lock timing # button changed function confirmation parking lights stay "on" for 30 sec. 1-chirp, led parking lights f...

  • Page 16

    16 about multiple car programming: multiple car (alarm) operation can only operate correctly when all transmitters on all systems are programmed in “b” mode (separate channel mode). You can not mix “a” mode programming and “b” mode programming. Follow the transmitter coding information in this manua...

  • Page 17

    17 to test the basic functions of the alarm system (all models) repeat the following procedures. 1. Turn off the ignition key and exit the vehicle closing all protected entrances. 2. Press the lock button on the transmitter. You will hear a siren/horn chirp, the parking lights will flash one time an...

  • Page 18

    18 starter disable: (also applies if ala-rps2 was installed to interrupt other circuits) 1. Enter the vehicle and close all the entrances. 2. Arm the alarm using the transmitter. 3. Turn the ignition key to the start position. The engine will not crank over. 4. Turn the ignition key to the off posit...

  • Page 19

    19 rf tamper re-arm: note: this feature is activated automatically when the alarm is programmed for automatic arming. See “remote feature programming” for details. (page 14, 15) 1. Alarm must be programmed for automatic arming. 2. Close all protected entrances and arm the alarm with the remote trans...

  • Page 20

    M4, m5 controller pink wire parking lights relay input red wire with white stripe parking lights relay output violet wire positive door pin trigger input green wire negative door pin trigger input blue wire negative aux trigger input brown wire siren output (+) blue wire with white stripe connection...