Magnavox MFX-450 User Manual

Manual is about: DIGITAL SURROUND SOUND RECEIVER

Summary of MFX-450

  • Page 1

    Home threater set in a box for model mmx450/17 item list consist of: 1. Receiver mfx 450/17 2. Satellite speakers mcs 990/17 3. Sub-woofer msw 990/17 for dfu of mfx450/17, please refer to the next page..

  • Page 2

    S m a r t . V e r y s m a r t . User guide digital surround sound receiver read this manual first! Congratulations on purchasing this magnavox product. We’ve included everything you need to get started. If you have any problems, magnavox representatives can help you get the most from your new produc...

  • Page 3: Warranty

    This “bolt of lightning” indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The “exclamation point” calls attention to features for which you should read the enclosed literature closely t...

  • Page 4

    3 english ....................................................2 español .................................................29 english español english: this digital apparatus does not exceed the class b limits for radio noise emissions from digital apparatus as set out in the radio interference regulat...

  • Page 5

    4 english 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer´s instructions. 8. Do not i...

  • Page 6

    5 english general information this receiver is supplied including: – a remote control – 2 batteries for the remote control, size aa – a coaxial cable for audio connection with a dvd player – a coaxial cable for the cinema link connection – a loop antenna – a wire antenna – this instruction booklet i...

  • Page 7

    6 english controls 1 power / standby.......Switches the receiver on and off. 2 cinema link ................Switches on and off the system control bus between the receiver and the tv. 3 ..........................................Sensor for the infrared remote control. 4 virtual...........................

  • Page 8

    7 english remote control open the battery compartment of the remote control and insert 2 alkaline batteries, type aa (r06, um-3). Remove batteries if they are dead or if the remote control will not be used for a long time. Batteries contain chemical substances, so they should be disposed of properly...

  • Page 9

    8 english remote control h mute .....................Mutes the sound of the receiver in all modes, except tv. Mutes the sound of your philips tv set if your remote control is in tv mode. 2 ................................Switches the source selected on your remote control (e.G. Vcr, tv) to standby. ...

  • Page 10

    9 english connectors connectors connectors name connect to: 6.3 mm headphone jack 1 phones a headphone with a 6.3 mm plug. At the front. Front speakers 2 r, l right and left front speaker. 3 center center speaker. Surround speakers 4 r, l right and left surround speaker. Audio in/out 6 cdr/tape out ...

  • Page 11

    10 english analog audio connections connectors there are analog and digital connectors available on some appliances. If possible use the digital connection; usually this will result in better sound quality. See “reassigning a source selection” on how to use the digital connectors of the receiver. Be...

  • Page 12

    11 english connections digital audio connections digital audio in/out phono vcr tv sat audio in/out in in in play out rec in phono gnd. Am loop dvd mon vcr sat coax 1 in coax 2 in r l surr. Center subw. Front optical in fm 300 Ω coax out video in/out antenna cd recorder cd player dvd player in out i...

  • Page 13

    12 english connections system control bus, cinema link video connections antenna digital audio in/out phono vcr tv sat cd cdr/tape audio in/out in in in play out rec in in in play out rec pre-out center caution risk of electric shock do not open avis risque de choc electrique ne pas ouvrir designed ...

  • Page 14

    13 english connections the type plate is located on the rear of the receiver. 1 check whether the power voltage as shown on the type plate corresponds to your local power voltage. If it does not, consult your dealer or service organization. 2 connect the power cord to the power outlet. To disconnect...

  • Page 15

    General hints for positioning avoid positioning the speakers in a corner or on the floor as this will boost the bass tones too much. Placing the speakers behind curtains, furniture, etc. Will reduce the treble response. The listener should always be able to ”see” the speakers. Each room has differen...

  • Page 16

    15 english system setup once the number and position of loudspeakers has been fixed, you can adjust the initial receiver settings for optimum surround sound with the actual setup: 1 set which speakers have been connected to the receiver (see “menus / speakr setup”). Note: the initial setting of your...

  • Page 17

    16 english display the display of the receiver is divided into 4 sections, which are to be used for the following: speaker diagram a rectangle with a letter in it shows that a speaker has been selected in the setup menu. However, the subwoofer indicator will only light when a subwoofer signal is ava...

  • Page 18

    17 english menus the receiver is equipped with a menu system. The menu is used for the setup of the receiver. The different menu options are related to each other in a logical way. Let’s assume you have no center speaker connected, and so you switched center speakr to no. If you try to use vol cente...

  • Page 19

    18 english menus * select input assigns the audio input connectors to the different source selections chosen with source select (see “source selection” for details). Coax1 digital coaxial input 1, coax 1 in coax2 digital coaxial input 2, coax 2 in opt digital optical input, optical in sat in analog ...

  • Page 20

    19 english source selection when selecting a source by turning source select, the audio and video inputs with the corresponding name are activated. The incoming signal is reproduced by all audio and – if the source includes a video signal – video outputs of the receiver. It is possible to reassign a...

  • Page 21

    20 english playback, recording 1 press power / standby to switch on the receiver. 2 turn source select to select a source. Y the name of the source is displayed. 3 start playback of the source as usual. • turn volume to adjust the volume. Y volume and the volume level between 0 and 50 is displayed. ...

  • Page 22

    21 english surround sound surround sound gives you a completely new listening sensation. You will have the feeling of being in the middle of the action, because sound is coming from everywhere around you. Look out for tv broadcasts, audio and video tapes and discs with the 3, 1 or marks which are en...

  • Page 23

    Surround sound 22 hall the sound reproduction is enhanced and a slight echo is added. This gives the impression of being in a large room. Can only be used in stereo mode. Surround the surround mode enables normal surround sound reproduction with 4 or 5 speakers. Depending on the source material, dol...

  • Page 24

    23 english tuner you can search for radio stations by scanning the frequency band. You can also key in the frequency of a known radio station. If an fm station is being broadcast and received in stereo, stereo is shown. Searching for radio stations 1 turn source select to select the tuner. Y tuner i...

  • Page 25

    24 english tuner 1 turn source select to tuner to select the tuner. Y tuner is displayed. 2 turn tuner preset x to select a preset radio station. Y preset , the preset number and station are displayed. After programming radio stations, you might want to change their sequence. Reshuffle allows you to...

  • Page 26

    25 english technical data subject to modification without notice. General power consumption .........................................................260 w standby power consumption ............................................ Dimensions, w × h × d ............................435 × 135 × 350 mm weigh...

  • Page 27

    26 english troubleshooting problem possible cause solution set does not work the overheating safety circuit switch the set off and let it cool down. After and is in standby mode has been activated. Having let the set cool down switch it on again and select a source by rotating source select or press...

  • Page 28

    Magnavox audio system one year free exchange this product must be carried in for an exchange. Limited warranty who is covered? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. What i...

  • Page 29

    28 mfx450_eng 11/26/02 3:21 am page 28.

  • Page 30: Verificación

    El símbolo del «rayo» indica que algún material no aislado dentro de su unidad podría resultar en una sacudida eléctrica. Para la seguridad de todos, favor de no remover la cubierta del producto. El «signo de exclamación» le llama la atención a características sobre las que ud. Debe leer la informac...

  • Page 31

    30 español 1. Lea estas instrucciones. 2. Conserve estas instrucciones. 3. Lea todos los avisos. 4. Siga todas las instrucciones. 5. No utilice este aparato cerca del agua. 6. Para limpiar el aparato utilice sólo un trapo seco. 7. No tape las aperturas de ventilación. Proceda a su instalación de acu...

  • Page 32

    31 español informaciÓn general este receptor viene acompañado de los siguientes componentes: – un mando a distancia – 2 pilas para el mando a distancia, tamaño aa – un cable coaxial para conexión de audio con un reproductor de dvd – un cable coaxial para la conexión de cinema link – una antena de cu...

  • Page 33

    32 español controles 1 power / standby.......Enciende/apaga el receptor. 2 cinema link ................Activa/desactiva el sistema de control en bus entre el receptor y el televisor. 3 ..........................................Detector para el mando a distancia de infrarrojos. 4 virtual................

  • Page 34

    33 español mando a distancia abra el compartimento de las pilas del mando a distancia e introduzca 2 pilas alcalinas, tipo aa (r06, um-3). Si las pilas están desgastadas o no va a utilizar el mando a distancia durante un largo período, extráigalas del compartimento. Las pilas contienen sustancias qu...

  • Page 35

    34 español mando a distancia h mute .....................Anula el sonido del receptor en todos los modos, excepto el de tv. Anula el sonido del equipo de tv philips, si el mando a distancia está en modo tv. 2 ................................Cambia el origen seleccionado en el mando a distancia (p. E...

  • Page 36

    35 español conectores nombre del conector conexiones toma de auriculares de 1 phones para la toma de auriculares de 6,3 mm en la parte frontal. 6,3 mm en la parte frontal. Front speakers 2 r, l para los altavoces frontales izquierdo y derecho. 3 center para el altavoz central. Surround speakers 4 r,...

  • Page 37

    36 español conexiones de audio analógicas conexiones algunos aparatos poseen conectores analógicos y digitales. Siempre que sea posible utilice la conexión digital; obtendrá una calidad mejor de sonido. Para aprender a utilizar los conectores digitales del receptor vea «para reasignar una selección ...

  • Page 38

    37 español conexiones conexiones de audio digitales digital audio in/out phono vcr tv sat audio in/out in in in play out rec in phono gnd. Am loop dvd mon vcr sat coax 1 in coax 2 in r l surr. Center subw. Front optical in fm 300 Ω coax out video in/out antenna cd recorder cd player dvd player in ou...

  • Page 39

    38 español conexiones sistema de control en bus, cinema link conexiones de vídeo antenna digital audio in/out phono vcr tv sat cd cdr/tape audio in/out in in in play out rec in in in play out rec pre-out center caution risk of electric shock do not open avis risque de choc electrique ne pas ouvrir d...

  • Page 40

    39 espa ñ ol conexiones la placa tipo está situada en la parte posterior del receptor. 1 compruebe que la tensión indicada en la placa tipo corresponde con el voltaje de la red local. De lo contrario, consulte con su distribuidor u organización de servicio 2 conecte el cable de alimentación al enchu...

  • Page 41

    40 espa ñ ol configuraciÓn del sistema indicaciones generales sobre el emplazamiento evite la colocación de los altavoces en una esquina o en el suelo, ya que esto reforzará demasiado los tonos graves. La respuesta de los agudos disminuirá si coloca los altavoces detrás de cortinas, muebles etc. La ...

  • Page 42

    41 espa ñ ol configuraciÓn del sistema una vez establecidos el número de altavoces y su colocación, puede ajustar la configuración inicial del receptor para obtener un sonido ambiental óptimo con la configuración real: 1 defina qué altavoces se han conectado al receptor (consulte «menús / speakr set...

  • Page 43

    42 espa ñ ol pantalla la pantalla del receptor está dividida en 4 secciones que se utilizan para lo siguiente: dibujo de los altavoces en el menú de ajustes, un rectángulo con una letra es indicación de que se ha seleccionado un altavoz. De cualquier forma, el indicador del subwoofer se encenderá só...

  • Page 44

    43 espa ñ ol menÚs el receptor está equipado con un sistema de menú. El menú se utiliza para la configuración del receptor. Las diferentes opciones del menú están interrelacionadas unas con otras siguiendo una lógica. Supongamos que no tiene un altavoz central conectado, y por consiguiente center sp...

  • Page 45

    44 espa ñ ol menÚs * select input (selección de entrada) asigna los conectores de entrada audio a las diferentes selecciones de fuente elegidas con source select (vea «selección de fuente» para obtener más detalles). Coax1 entrada coaxial digital 1, coax 1 in coax2 entrada coaxial digital 2, coax 2 ...

  • Page 46

    45 espa ñ ol selecciÓn de fuente cuando seleccione una fuente dando vueltas a source select, se activan las entradas de audio y vídeo correspondientes a ese nombre. Todas las salidas de audio y vídeo (si la fuente incluye una señal de vídeo) del receptor, reproducen la señal de entrada. Es posible r...

  • Page 47

    46 espa ñ ol reproducciÓn, grabaciÓn 1 pulse power / standby para encender el receptor. 2 gire source select para seleccionar la fuente. Y el nombre de la fuente aparece en pantalla. 3 inicie la reproducción normal de la fuente. • gire volume para ajustar el volumen. Y aparece en pantalla volume jun...

  • Page 48

    47 espa ñ ol sonido envolvente el sonido envolvente le ofrece una calidad de sonido innovadora. Le dará la sensación de hallarse en medio de la acción, ya que el sonido se reproduce a su alrededor. Procure utilizar programas de tv, cintas de vídeo o audio y discos con los símbolos 3, 1 o que estén c...

  • Page 49

    48 espa ñ ol sonido envolvente hall esta modalidad realza la reproducción del sonido y añade un ligero eco. Esto produce la sensación de estar en una habitación grande. Sólo puede utilizarse en la modalidad de estéreo. Surround la modalidad de sonido envolvente permite la reproducción de sonido con ...

  • Page 50

    49 espa ñ ol sintonizador se pueden buscar las emisoras de radio efectuando un barrido por la banda de frecuencias. También se puede teclear la frecuencia de una emisora conocida. Si se emite una emisora fm y se recibe en estéreo, aparece stereo . Búsqueda de emisoras de radio 1 gire source select p...

  • Page 51

    50 espa ñ ol sintonizador 1 gire source select y elija tuner para seleccionar el sintonizador. Y aparece en pantalla tuner. 2 gire tuner preset x para seleccionar la emisora preseleccionada. Y aparecen en pantalla preset , el número de preselección y la emisora. Quizá desee cambiar el orden de las e...

  • Page 52

    51 espa ñ ol datos tÉcnicos sujeto a modificaciones sin previo aviso. General consumo de energía .......................................................260 w consumo de energía en espera........................................ Dimensiones, anch. × alt. × profun.........435 × 135 × 350 mm peso .........

  • Page 53

    52 espa ñ ol soluciÓn de problemas problema causa posible soluciÓn no funciona y está en el circuito de seguridad para apague el aparato y déjelo enfriar. Después de modo de espera sobrecalentamiento ha sido activado. Dejar que el aparato se enfríe, enciéndalo de nuevo y seleccione una fuente girand...

  • Page 54

    Sistema de audio cambio gratis por un año se necesita presentarse en persona con este producto para cambiarlo. Garantia limitada ¿quien tiene proteccion? Usted debe tener su comprobante de venta para recibir servicio bajo la garantía. Una nota de venta u otro documento mostrando que usted compró el ...

  • Page 55

    Espa ñ ol 3140 115 3000.2 printed in china ib8387t001/hk0241 meet magnavox at the internet http://www.Magnavox.Com w english mfx450_spa 11/26/02 3:23 am page 54.