Service manual dvd player mwd200fa mwd200g open/close play stop standby-on open/close play stop ir standby-on.
Important safety notice proper service and repair is important to the safe, reliable operation of all funai equipment. The service procedures recommended by funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should b...
1-1-1 e6a60sp specifications notes: 1. All items are measured without pre-emphasis unless otherwise specified. 2. Power supply: ac 120 v, 60 hz 3. Load impedance: 100 k Ω load (audio output) 4. Room ambient: +25 °c item conditions unit nominal limit 1. Video output 75 Ω load vpp 1.0 ± 0.1 2. Coaxial...
1-2-1 e7nlsp laser beam safety precautions this dvd player uses a pickup that emits a laser beam. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not loo...
1-3-1 dvdn_isp important safety precautions product safety notice some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for ...
1-3-2 dvdn_isp safety check after servicing examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance w...
1-4-1 dvdn_sn standard notes for servicing circuit board indications 1. The output pin of the 3 pin regulator ics is indicated as shown. 2. For other ics, pin 1 and every fifth pin are indicated as shown. 3. The 1st pin of every male connector is indicated as shown. Instructions for connectors 1. Wh...
1-4-2 dvdn_sn 3. The flat pack-ic on the cba is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the ic when removing it. With soldering iron: 1. Using desoldering braid, remove the solder from all pins of the flat pack-ic. When you use solder fl...
1-4-3 dvdn_sn with iron wire: 1. Using desoldering braid, remove the solder from all pins of the flat pack-ic. When you use solder flux which is applied to all pins of the flat pack-ic, you can remove it easily. (fig. S-1-3) 2. Affix the wire to a workbench or solid mounting point, as shown in fig. ...
1-4-4 dvdn_sn instructions for handling semi- conductors electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for human body be sure to wear a grounding band (1 m Ω) that is properly grounded ...
1-5-1 e6a60dc cabinet disassembly instructions 1. Disassembly flowchart this flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally. 2. Disassembly method note...
1-5-2 e6a60dc [2] front assembly (l-2) (l-1) (l-1) fig. D2 [3] reinforce plate (s-2) (s-2) fig. D3 [4] dvd main cba unit (s-3) cn201 cn301 cn401 cn601 a fig. D4 view for a short the three short lands by soldering. (either of two places.) fpc cable.
1-5-3 e6a60dc 3. How to eject manually 1. Turn the unit over. 2. Insert the shaft less than a diameter of 3 mm (e.G. Screwdriver) straightly into the opening as shown. 3. Turn the shaft along with the opening clockwise. 4. Repeat steps 2 and 3 until the tray will open. 5. Pull the tray slowly manual...
1-6-1 e6a60int how to initialize the dvd player to put the program back at the factory-default, initialize the dvd player as the following procedure. 1. Press [1], [2], [3], [4], and [display] buttons on the remote control unit in that order. Fig. A appears on the screen. 2. Press [clear] button on ...
1-7-1 e6a60fw firmware renewal mode 1. Turn the power on and remove the disc on the tray. 2. To put the dvd player into version up mode, press [9], [8], [7], [6], and [search mode] buttons on the remote control unit in that order. The tray will open automatically. Fig. A appears on the screen. The d...
1-8-1 block diagrams system control / servo block diagram e6a60bls ic301 (ser v o drive) cn301 m sled motor m spindle motor ic101 (micr o contr oller) + - + - + - + - + - + - + - sled mo t o r drive focus a ctu a t or drive spindle mo t o r drive tra cking a ctu a t or drive 126 tra y -in sld 67 spd...
1-8-2 digital signal process block diagram e6a60bld c1 6 d1 8 a1 7 b1 5 d vd-ld 8 cd-ld 10 pd-moni 7 fs(+) 2 fs(-) 3 ts(+) 1 ts(-) 4 cn201 cn201 cn201 ic201 (sw) ic101 (micr o contr oller) fs fs(+) cd/d vd fs(-) ts(+) ts(-) ts detect or cd/d vd 19 q251,q252 cd d v d amp q253,q254 amp 4 1 3 6 gnd(d v...
1-8-3 video / audio block diagram e6a60blv jk1202 jk1201 amp q1351 ic1201 q1201 q1202 +5v (amp) cn601 cn1601 12 11 a udio(l) 14 13 a udio(r) 13 12 a udio(l)-mute a udio(l)- out 1 6 7 5 a udio(r)- out 16 15 spdif +3.3v q1204 3 2 wf6 wf4 wf5 a udio signal video signal d vd main cb a unit a v cb a cn60...
1-8-4 e6a60blp power supply block diagram 3 ic1006 (shunt regulator) reg ac1001 ac cord f1001 1a 250v line filter l1001 d1001, d1002 d1004, d1005 q1003 q1031 2 4 7 3 4 ic1001 error voltage det t1001 11 12 13 15 14 16 17 18 switching switching control 1 2 6 bridge rectifier ho t a v f hot circuit. Be...
1-9-1 e7n_sc schematic diagrams / cba’s and test points standard notes warning many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement compone...
1-9-2 e7n_sc list of caution, notes, and symbols used in the schematic diagrams on the following pages: 1. Caution: for continued protection against fire hazard, replace only with the same type fuse. Attention: pour une protection continue les risqes d'incele n'utiliser que des fusible de mÊme type....
1-9-3 dvd main 1/3 schematic diagram e6a60scd1 1 note: either ic461 or ic462 is used for dvd main cba unit. Dvd main 1/3 ref no. Position ic201 c-1 ic202 d-4 ic301 d-3 ic461 f-1 ic462 e-1 q251 c-2 q252 b-2 q253 c-2 q254 b-2 cn201 a-3 cn301 a-1 cn401 f-3 connectors ics transistors.
1-9-4 dvd main 2/3 schematic diagram e6a60scd2.
1-9-5 dvd main 3/3 schematic diagram e6a60scd3 dvd main 3/3 ref no. Position ic103 n-3 ic501 o-4 cn601 r-1 ics connector.
1-9-6 av 1/2 schematic diagram e6a60scav1 caution ! Fixed voltage (or auto voltage selectable) power supply circuit is used in this unit. If main fuse (f1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the ac plug to the ac power supp...
1-9-7 av 2/2 schematic diagram e6a60scav2 av 2/2 ref no. Position ic1201 h-1 ic1403 i-4 q1201 j-1 q1202 j-1 q1204 i-1 q1351 j-4 cn1601 g-3 ics transistors connector.
1-9-8 be6a60f01011 av cba top view caution ! Fixed voltage (or auto voltage selectable) power supply circuit is used in this unit. If main fuse (f1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the ac plug to the ac power supply. Oth...
1-9-9 wf2 pin 9 of cn1601 wf1 pin 7 of cn1601 wf3 c1402 plus lead wf4 pin 11 of cn1601 wf5 pin 13 of cn1601 wf6 pin 15 of cn1601 av cba bottom view be6a60f01011 av cba ref no. Position ic1001 d-3 ic1002 c-1 ic1006 d-3 ic1201 d-1 ic1403 d-2 q1002 b-1 q1003 d-3 q1004 b-1 q1008 d-3 q1011 c-1 q1016 c-1 ...
Waveforms e7nwf 1-10-1 wf6 wf1 wf3 wf4 wf5 wf2 pin 15 of cn1601 pin 7 of cn1601 c1402 plus lead pin 11 of cn1601 pin 13 of cn1601 pin 9 of cn1601 20 µs 0.2v video-y video-c 0.2v 20 µs video-cvbs 0.5v 20 µs audio(l) 0.5v 0.5ms 0.5ms audio(r) 0.5v 0.5ms spdif 1v 0.1 µs note: input dvd: color bar signa...
Wiring diagram e6a60wi 1-11-1 cn201 cn301 tray-in ev+1.2v 4 1 ev+1.2v 5 2 ev+3.3v 7 4 ev+3.3v 8 5 p-on+3.3v 9 6 p-on+5v 10 7 ev+10v 11 8 ev+10v 12 9 gnd 13 10 gnd 14 11 gnd 15 12 gnd 16 13 gnd 17 14 gnd 18 15 gnd 19 16 pwrcon 20 17 power 21 18 open/close 22 19 stop 23 20 play 24 21 remote 25 22 cn40...
1-12-1 e7nti system control timing charts tray in (tl221) sled drive (tp303) disc drive (tp301) focus drive (tp304) tracking drive (tp302) 0v 3.3v 0v 1.65v 0v 0v 0v 1.65v 1.65v 1.65v tray close ~ play / play ~ tray open tray close disc rotation play disc stop tray open.
1-13-1 e6a60le lead identifications 1 2 3 g d s 8 5 4 1 1: r 2: a 3: k 1 2 3 1 2 4 3 1: a 2: k 3: e 4: c 8 5 4 1 mm1636xwre 1: gnd 2: vout 3: vin e c b e c b note: a: anode k: cathode e: emitter c: collector b: base r: reference g: gate d: drain s: source kia4558p/p kta1266-y-at/p ktc3203-y-at/p kta...
1-14-1 e6a60cex exploded views cabinet ac1001 f1001 jk1202 jk1401 jk1402 av cba jk1201 see electrical parts list for parts with this mark. Some ref. Numbers are not in sequence. A29 2l041 2l041 2l105 2l021 2l021 dvd main cba unit 2l021 2l011 2l011 1b1 a15 a16 2l031 a1x a22 a23 2l081 2b5 2l081 a21 a ...
1-14-2 e6a60pex packing a22 s1 s2 s4 unit s2 x10 x5 x2 x4 x1.
20051207 1-15-1 e6a60ca mechanical parts list product safety note: products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through imp...
20051207 1-16-1 e6a60el electrical parts list product safety note: products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through imp...
20051207 1-16-2 e6a60el ic1006 shunt regulator tl432a-ta nszba0t2t002 ic1201 ic op amp kia4558p/p nszba0sjy035 ic1403 driver for dvd mm1636xwre qszba0tmm108 coils l1001# line filter 20mh sa-00911 llbg00zsa003 l1007 choke coil 22 µh-k llbd00pkv021 l1009 choke coil 22 µh-k llbd00pkv021 l1060 pcb jumpe...
Mwd200fa/mwd200g e6a60/a0ud 2005-12-27.